Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Air vs Volume  (Read 1463 times)

0 Members and 1 Guest are viewing this topic.

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Air vs Volume
« on: December 11, 2019, 08:25:12 PM »

This is a bit of a two part question but I have two pretty similar Pre-Pokerwork boxes that I play pretty often. One is a total beater with more patches that bellows tape that is loud as could be and another that is a family heirloom that I've mostly restored and tuned but just doesn't have the volume that I'd like. Tight bellows aside am I missing something to make it louder? The second question here is about the bellows on said box. I completely stripped and retaped the bellows and have tried to shine a flashlight through the bellows in a dark room to find obvious holes but I just can't seem to locate where air is escaping. I've also added new bellows foam seal so I didn't really suspect that seal too much. Any help would be appreciated.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Air vs Volume
« Reply #1 on: December 11, 2019, 09:32:08 PM »

Old Hohner bellows can just become porous with so many tiny leaks that it’s possible to identify them.  I had a similar experience with a 1930s Hohner.  A new set off bellows transformed it’s airtightness.

Volume - have you restricted the treble button travel?  Lack of pallet lift will limit volume.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Air vs Volume
« Reply #2 on: December 11, 2019, 09:48:58 PM »

Old Hohner bellows can just become porous with so many tiny leaks that it’s IMpossible to identify them.
FTFY

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Air vs Volume
« Reply #3 on: December 12, 2019, 12:10:39 AM »

Old Hohner bellows can just become porous with so many tiny leaks that it’s possible to identify them.  I had a similar experience with a 1930s Hohner.  A new set off bellows transformed it’s airtightness.

Volume - have you restricted the treble button travel?  Lack of pallet lift will limit volume.

I have limited my button travel and added pallet felt. Is there a general guideline for how much they should open?
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Air vs Volume
« Reply #4 on: December 12, 2019, 12:35:20 AM »

The air holes in a hohner fondo are (I think) 10mm diameter. if the centre of the pallet is then 5+ mm clear of the fondo  the airhole itself is the most restrictive area outside of the reed.

The physics of wave propogation is a bit more complicated than that but pallet opening of half diameter of orifice  will take you into the right ball park.

3.142 x r2= Area of fondo orifice

3.142 x 2 x r x h = area of open cylindrical boundary between fondo orifice and pallet, where h= distance between pallet face and fondo.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Air vs Volume
« Reply #5 on: December 12, 2019, 01:43:12 AM »

Old Hohner bellows can just become porous with so many tiny leaks that it’s possible to identify them.  I had a similar experience with a 1930s Hohner.  A new set off bellows transformed it’s airtightness.

Volume - have you restricted the treble button travel?  Lack of pallet lift will limit volume.

I have limited my button travel and added pallet felt. Is there a general guideline for how much they should open?
After adding new pallet felt did you readjust the button height ? Sometimes its needed to allow pallet to open fully.
Lester’s videos show this.

When working on finding holes in bellows I found holding the bellows close to a strong light while holding them open ( I made a jig to hold them open) and looking though the inside to the outside ( where the light is ) works well. This also makes marking the spot easier. This method requires you to look for light at different angles, so moving the bellows around to inspect corners etc.
I found it dark enough inside the bellows to spot the light outside the bellows.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Air vs Volume
« Reply #6 on: December 12, 2019, 07:52:35 AM »

Moistened lips are usually a very  effective way of detecting and locating leaks in bellows.
Logged

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Air vs Volume
« Reply #7 on: December 14, 2019, 04:37:10 AM »

/quote]
After adding new pallet felt did you readjust the button height ? Sometimes its needed to allow pallet to open fully.
Lester’s videos show this.
[/quote]

Good to know, is there a link to this or is it part of the "hot rod your Hohner" bit? I've been meaning to look that up.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Air vs Volume
« Reply #8 on: December 14, 2019, 08:28:00 AM »

After adding new pallet felt did you readjust the button height ? Sometimes its needed to allow pallet to open fully.
Lester’s videos show this.

Good to know, is there a link to this or is it part of the "hot rod your Hohner" bit? I've been meaning to look that up.

Yes - its on the 'Refacing the Treble Pallets' video, specifically starting here.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal