Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Tuning a Hohner 1040  (Read 950 times)

0 Members and 1 Guest are viewing this topic.

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Tuning a Hohner 1040
« on: December 11, 2019, 08:30:21 PM »

I set to doing a tuning job today, a Hohner 1040 in C. This was my first time working on an instrument without removable reed blocks and it was a bit of an eye opener I have to say. I couldn't use my usual tuning table as it's set up to tune reeds on blocks, not whole treble or bass ends of instruments. I do have a couple of cut out boards for fine tuning boxes with reeds in situ on their own bellows, so I set that up on a workmate (see photo) and it worked well as the task was more like a brush up tuning than a full scale job.

Most of the reeds were sharp, with only a dozen or so that were flat, luckily most of those were push reeds. I found working on flat mounted reeds quite awkward and ended up wishing I had a bit of 'L' shaped spring steel to support the reeds when filing or scratching as the straight one I have was cumbersome to use and I damaged a couple of perfectly good valves when I was flailing around inside.

It's done now though and I'm pretty pleased with the result, but I am pondering whether to change the first button pull G3 to A3. Is that a sensible thing to do or am I missing something?
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Tuning a Hohner 1040
« Reply #1 on: December 11, 2019, 08:48:16 PM »

Irish and Quebec players usually tune that note from G3 to A3 so you're in good company.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Tuning a Hohner 1040
« Reply #2 on: December 11, 2019, 09:17:41 PM »

I use a piece of brass and bend the end and use that as a support. I’ve also got a piece of needle file glued onto an L shaped handle, in order to file the reed tip in situ. It’s v easy to mess up the set of the reed (the gap) esp on the inside reed, in which case I resort to taking it off, resetting and taping it back to tune it and then rewax it when it’s tuned. It’s pretty difficult to get at a small/high inside reed without messing it up in some way when they are mounted flat and down in the case. I’m pretty sure they are pretuned before fitting. If I’m fitting new reeds I tack them in first, get the tuning sorted, then wax them in.

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Tuning a Hohner 1040
« Reply #3 on: December 12, 2019, 12:44:46 AM »

Irish and Quebec players usually tune that note from G3 to A3 so you're in good company.

And that change gives you Peter Wyper's patent keyboad arrangement - so you really are in good company. 
Logged

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Tuning a Hohner 1040
« Reply #4 on: December 12, 2019, 03:19:45 AM »

Tuning a reed up a whole tone is something I wouldn't normally do, are these low reeds chunky enough to take it without running the risk of ruining them? Would it be better to swap them out with 2 x F#3/A3 plates from a D row and take the F#s down a tone with a bit of solder, or even 2 x E3/G#3 plates from an A row then I only have to tune the G#s up a semitone?
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Tuning a Hohner 1040
« Reply #5 on: December 12, 2019, 09:10:24 AM »

Yes, best not to tune the existing reeds up a whole tone.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal