Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Soldering Iron For Reed Waxing  (Read 4604 times)

0 Members and 1 Guest are viewing this topic.

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: Soldering Iron For Reed Waxing
« Reply #20 on: October 27, 2021, 04:16:47 PM »

.
I had a Hanmatek though in my Raspberry Pi days.  Easy to use and very controllable 👍 Much better than my old one

Had a plan to use it for melodeon repairs, but I have now passed it on to a mediaeval armourer
Logged
  _       _    _      _ 

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Soldering Iron For Reed Waxing
« Reply #21 on: November 05, 2021, 04:49:16 PM »

On the back of the ongoing discussion about using a Soldering Iron ( designed to melt 'metal alloy') to melt wax, as against using an Encaustic Tool, designed to melt........'wax' ! I decided to look at some options to improve on the 'stock' 'nibs' that come with 99% of the Encaustic Tools in the packet, which tend to be a 'large' heart shape, a square, a wire brush and a 'split nib', none of which are really suited to reed work.

I ended up buying x3 different 'petal' shaped attachments as part of an 'offer' and used a standard needle file to grind a furrow in them.

https://thecraftstore.com/product/47423/encaustic-art-3-x-pick-n-mix-tips-for-stylus-pro/098806?gclid=Cj0KCQjw8eOLBhC1ARIsAOzx5cF2WyYe9d9LNfnDN66oMT1cQVzTXG8jVi5N5rRKLZ0JTGx_2bUVtNAaAjQ6EALw_wcB

The 'Droplet' is best suited to the task although the 'long petal tip' might well wax between Lilliput sized plates.

The end result creates a flat surface against which a 'strip' of wax can be run into the groove.....the wax populates the furrow and runs off the pointed tip like posh writing with a Parker fountain pen.  The tip is small enough to fit very successfully between standard placed reeds.  Because the tool is regulated to suit wax there is no smoking/smell.

Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Soldering Iron For Reed Waxing
« Reply #22 on: July 13, 2024, 09:22:27 AM »

Here's what I found to be the best solution (by far).

There's a very good temp-controlled soldering Iron called "A-BF GS90D". If you shop around, you can get one for under £30 delivered. Well-made and works like a dream for soldering - if only I had something like this in my teenage years  >:E
Note: If you get it with a non-UK plug you're advised to cut it off and install a UK one instead of using a plug adapter. The adapters tend to spark and this sparking will fry your temp control chip in no time.

For actual soldering I use solid brass tips instead of the fancy never-works-right plated long-life ones that it comes with.

But for waxing you can take the wider long-life bit, drill a hole in it and bolt on a wee brass plate. Has to be a bolt-on design to be able to install it.
Set the temp to, say, about 100 degrees or whatever works for you, and Bob's your uncle. You can use the "spoon" to do single wax-in wax-outs, or you can scoop-melt some wax onto the hot spoon right off the hard block and then feed it onto the reedblock.

PXL-20240713-081112352" border="0
PXL-20240713-081100041" border="0
PXL-20240713-081010274" border="0
PXL-20240713-081001242" border="0
<a target='_blank' href='https://imgbb.com/'>imagehosting[/url]
« Last Edit: July 13, 2024, 09:24:14 AM by mChavez »
Logged
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal