Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Wilkinson of Glasgow: Excelsior Accordeon Project  (Read 6564 times)

0 Members and 1 Guest are viewing this topic.

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Wilkinson of Glasgow: Excelsior Accordeon Project
« Reply #20 on: January 17, 2021, 11:58:43 AM »

Thanks Nick  :D
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Wilkinson of Glasgow: Excelsior Accordeon Project
« Reply #21 on: January 18, 2021, 08:04:59 PM »

I repadded the bass spoons  yesterday.... my previous efforts in this direction have involved cutting circles with scissors and haven't been as neat as I would have liked. This time I dug out a compass cutter, intended for (children's?) craft projects, that I bought a couple of years ago when I saw them on display in the Kyle pharmacy.

It produced a much neater job- The trick was very much to make sure the pin stayed stuck in the leather and go round very gently and slowly. There were a couple where a single fibre somehow evaded the blade, rather than pull the circle out I cut these last strands of collagen with a craft knife.

I replaced the safety pin springs under a couple of the keys with springs from a PA keyboard...they are a bit on the soft side but seem to be holding the keys closed


« Last Edit: January 18, 2021, 08:07:55 PM by Peadar »
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Wilkinson of Glasgow: Excelsior Accordeon Project
« Reply #22 on: February 04, 2021, 11:14:53 PM »

Valves....though now I've sorted the pallet facings and they bedded in the box is playing fairly well....a couple of notes sounding odd but I haven't been able to work out what the problem is with the reeds.

The treble end valve leather is 0.55mm -0.6mm thick, with what looks like a skiver grain finish on the leather. Short of buying a half hide (which may not be uneconomic given the fact there's 4 Internationals and and 24 bass Excelsior in the queue for revalving) does anyone know where I cab get that spec of material - the leather valves are much thicker than the Viyella "modern equivalent"
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Wilkinson of Glasgow: Excelsior Accordeon Project
« Reply #23 on: February 05, 2021, 12:43:30 AM »

Valves....though now I've sorted the pallet facings and they bedded in the box is playing fairly well....a couple of notes sounding odd but I haven't been able to work out what the problem is with the reeds.

The treble end valve leather is 0.55mm -0.6mm thick, with what looks like a skiver grain finish on the leather. Short of buying a half hide (which may not be uneconomic given the fact there's 4 Internationals and and 24 bass Excelsior in the queue for revalving) does anyone know where I cab get that spec of material - the leather valves are much thicker than the Viyella "modern equivalent"

Just buy real leather valves from Charlie Marshall, together with 'dots and springs' for the larger ones.
http://www.cgmmusical.co.uk/CGM_Musical_Services/Reed_Valves.html#19
http://www.cgmmusical.co.uk/CGM_Musical_Services/Reed_Valves.html#20

Just be sure to replace all the valves at the same time. The sound from new leather valves will be fine. Remember that old leather valves become stiff with age and the present-day sound quality they impart is unlikely to be how the reeds sounded decades ago when the leather was new and flexible.

The quality of the leather valves which Charlie sells is excellent and the leather thickness is designed to be appropriate for the size/pitch of the reeds. If you really feel that you must have slightly thicker leather valves on some of the higher pitched reeds you could always use a larger, slightly thicker, valve but cut down to size.

Replacing any of the valve with any sort of make/material will nearly always mean slight tuning adjustments afterwards (but I expect you know that anyway).
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Wilkinson of Glasgow: Excelsior Accordeon Project
« Reply #24 on: February 05, 2021, 07:56:11 AM »

I’d also recommend using new ready made leather valves.  In a batch of valves you will often find some are softer and done a little stiffer.  It’s worth being selective with where you use the valves,  stiffer on larger reeds, softer in smaller valves where the valves need to be trimmed shorter.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Wilkinson of Glasgow: Excelsior Accordeon Project
« Reply #25 on: February 20, 2021, 10:58:21 PM »

Re-valve...starting with the bass reeds.
(Material ordered from Charlie Monday evening and arrived Wednesday)
Internal layout is simple enough. Reed plates pinned on leather gasket strips----which is glued in..looks like hot glue. The gasket itself will need replaced.  This box has still got original leather gaskets all round and that's the way it's staying.
« Last Edit: February 21, 2021, 11:14:10 AM by Peadar »
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Wilkinson of Glasgow: Excelsior Accordeon Project
« Reply #26 on: February 20, 2021, 11:21:27 PM »

A couple of photos  of the taking apart - the bass C#/G# only removed

1 - - A pin keep : Card board box with near full size sketch of reed layout on a sheet of card. The reed marks are sketched to help make sure they all go back right way round/same position and the pins pushed in as they are drawn from the reed chests.

2 - Close up of the bass reed chests - passage from the bass to the tenor reed chest visible. Interestingly the only sign of wax in the whole instrument is a tiny run down the long side of the tenor  reed, where it butts against the bass reed chest.

3 - C#/G# bass reed plate and removed valves. Valves appear to have been attached with a hot glue. The gasket strips also appear to have been fixed down with a hot glue. Hot glue may also have been used between reed plates and gasket. In comparison the treble end reeds are dry fixed against the  reed chest gaskets with screws.

(Edit - noting presence of wax)
« Last Edit: February 21, 2021, 11:19:15 AM by Peadar »
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Wilkinson of Glasgow: Excelsior Accordeon Project
« Reply #27 on: February 21, 2021, 05:07:40 PM »

Next question...
Should the valves cover the entirety of the reed slot or should they leave a small gap at the valve tip to let some air bleed through? The old valves appear to have a gap but I can't think why it might (or might not) be a good idea?
Logged

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Wilkinson of Glasgow: Excelsior Accordeon Project
« Reply #28 on: February 21, 2021, 05:14:01 PM »

They should cover the whole of the aperture, just. The old ones may have shrunk with age, (haven't we all? )

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Wilkinson of Glasgow: Excelsior Accordeon Project
« Reply #29 on: February 21, 2021, 06:38:29 PM »

They should cover the whole of the aperture, just. The old ones may have shrunk with age, (haven't we all? )

SJ
Thanks John. This box is full of surprises/challenges - partly because it's the first one I've really tried to do more than patch repairs on and partly because it's all leather gaskets, but generally in amazingly good internal condition for a 95 year old and I want to get it right.

Gasket strips...3mm wide x 1-1.5mm thick, glued to the reed chests. Reed plates just held down by pins. This will be a suck and see operation. treble end ones are all screwed which is more reliable.

Edited for clarity - gaskets glued to wood. but no glue between reed plate and gasket.
« Last Edit: February 24, 2021, 08:04:21 PM by Peadar »
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Wilkinson of Glasgow: Excelsior Accordeon Project
« Reply #30 on: February 21, 2021, 07:58:37 PM »

Quote
Gasket strips...3mm wide x 1-1.5mm thick. just held down by pins. This will be a suck and see operation. treble end ones are all screwed which is more reliable.

Yes, I was about to mention: usually these L-shaped pins are (or were, really) used with wax, I'm not sure they would be sufficient for use with a gasket.
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Wilkinson of Glasgow: Excelsior Accordeon Project
« Reply #31 on: February 21, 2021, 08:34:39 PM »

Quote
Gasket strips...3mm wide x 1-1.5mm thick. just held down by pins. This will be a suck and see operation. treble end ones are all screwed which is more reliable.

Yes, I was about to mention: usually these L-shaped pins are (or were, really) used with wax, I'm not sure they would be sufficient for use with a gasket.

The first reed out gave me the impression that glue had been involved, but historically leather gaskets, packings and piston rings  were very widely used e.g. in pumping machinery. I have seen leather seals stuck to metal by corrosion products. I now think that maybe happened with one of the reedplates, but the others have all been free and clearly held down only by the dog pins- how that will pan out when the pins go back in is another matter- Time and experiment will tell.

Plenty of railways were built with dog spiked track and I have a ready made solution* if respiking in the old holes fails.

*I hope
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Wilkinson of Glasgow: Excelsior Accordeon Project
« Reply #32 on: February 24, 2021, 01:05:17 AM »

For now I have just revalved the bass reeds....not touched the chords as yet - but they sound and feel OK.

I have used chamois leather (wash leather) for the gasket replacements, hot glued to the reed cribs and just pinned the reed plates down. I know Scott Bellinger at one point tested bellows pressure while playing, by connecting a manometer to his machine and got results of the order of 50mm of water - i.e. 5g/cm2 . the largest bass reed plates are 5cm x 2cm = 10 cm2... so subject to a potential blow out force  of 50g.  It takes a firm push to get the pins back down their pin holes so I may not need any other fixing.

It seems to have worked. A few log photos attached..

1. Arrangement for making chamois strip gaskets
2. Kitchen set up for glue work. Hide glue jar in pan of water. Pan has enough thermal mass to keep glue warm for some time.
3. New fitted bass valves.

« Last Edit: February 24, 2021, 01:09:11 AM by Peadar »
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Wilkinson of Glasgow: Excelsior Accordeon Project
« Reply #33 on: February 24, 2021, 07:23:04 AM »

Quote
Gasket strips...3mm wide x 1-1.5mm thick. just held down by pins. This will be a suck and see operation. treble end ones are all screwed which is more reliable.

Yes, I was about to mention: usually these L-shaped pins are (or were, really) used with wax, I'm not sure they would be sufficient for use with a gasket.

I've seen a few 1930s Hohners where the reed plates were fixed using the L-shaped nails and leather gaskets. No wax. They seemed to work alright.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Wilkinson of Glasgow: Excelsior Accordeon Project
« Reply #34 on: March 04, 2021, 10:29:02 PM »

Quote
Gasket strips...3mm wide x 1-1.5mm thick. just held down by pins. This will be a suck and see operation. treble end ones are all screwed which is more reliable.

Yes, I was about to mention: usually these L-shaped pins are (or were, really) used with wax, I'm not sure they would be sufficient for use with a gasket.

I've seen a few 1930s Hohners where the reed plates were fixed using the L-shaped nails and leather gaskets. No wax. They seemed to work alright.

The basses are holding alright so far. Did the C# row last weekend & that's OK. Everything I do makes the box a little bit tighter. It amazes me how little effort is needed on the draw. The bellows falling open under their own weight sound the box quite loud enough for playing in the house.
Logged
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal