Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Reedplate gasket and screws  (Read 3128 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Reedplate gasket and screws
« on: March 19, 2020, 02:29:23 PM »

I’d like to order some reedplate gasket/leather/whatever and appropriate screws for use in place of traditional wax (where applicable). I’ve heard that Carini is the place to order this stuff, but given the situation in Italy I think I’ll probably have to look elsewhere. Can anyone recommend a source? I’ve never used this stuff before so any additional advice would also be appreciated!
Logged
C#/D player

Dave Praties

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 195
Re: Reedplate gasket and screws
« Reply #1 on: March 19, 2020, 02:39:11 PM »

Yes, its easy. Charlie Marshall, (Scotland), sells Olivisc gasket material. <http://www.cgmmusical.co.uk/CGM_Musical_Services/Welcome.html>.  For Screws, go to Ebay and enter "Self-Tapping-Machine-Screws with Shoulder-Flange". These are just the job. Have fun! Dave
Logged
Castagnari Handry 18 G/C. Castagnari Handry 18 D/G.    Self-built G/C 2.5/12 bass. almost finished after 7 years! Bb/Eb Preciosa. C/F Lilliput.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reedplate gasket and screws
« Reply #2 on: March 19, 2020, 03:03:23 PM »

Carini are still open, just not allowing personal callers

http://www.carinidena.it/
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Reedplate gasket and screws
« Reply #3 on: March 19, 2020, 04:38:05 PM »

The Olovisc gasket material is really easy to use and very effective. It is self-adhesive with a backing sheet of thin paper.

Cut the olovisc into thin strips the length and width required, using a sharp blade and a straight edge on a cutting board. Apply to the cleaned up wood surfaces of the reed block, removing the backing paper a bit at a time and press the gasket gently in place. It is usually possible to carefully re-lift it and re-position if necessary.

Prick holes where your screws or nails are going to go and then simply secure the reed plates in to their positions. Job done.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Reedplate gasket and screws
« Reply #4 on: March 20, 2020, 01:30:33 PM »

Does anyone know if changing from wax to reed gaskets affects the tone or volume of an instrument? Is this a change anyone would make when refurbishing someone else’s box?

Regarding the self-tapping screws mentioned above, my concern is that sometimes there is *very* little wood between the reedplate openings in the block, and that many of the screws I’m finding are just too big.
Logged
C#/D player

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Reedplate gasket and screws
« Reply #5 on: March 20, 2020, 01:33:29 PM »

Does anyone know if changing from wax to reed gaskets affects the tone or volume of an instrument? Is this a change anyone would make when refurbishing someone else’s box?

Regarding the self-tapping screws mentioned above, my concern is that sometimes there is *very* little wood between the reedplate openings in the block, and that many of the screws I’m finding are just too big.
My concern would be the wood the blocks are made from. The blocks on screwed boxes are made from harder wood to take the strain of the screws whereas normal Hohner ones are made of quite soft wood and the screws may no grip.

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: Reedplate gasket and screws
« Reply #6 on: March 20, 2020, 01:44:49 PM »

you might consider liliput type small L shape pins too, I haave seen a few old hohners with gasket,reeds were attaced with L shape small pins on treble side and screwws on bass side. 
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Reedplate gasket and screws
« Reply #7 on: March 22, 2020, 03:37:02 AM »

I’m surprised that nobody spoke to my question regarding any perceivable difference in tonal quality or volume with gasket vs wax! I’ve heard it suggested that there may be a slight decrease in volume with the gasket?
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Reedplate gasket and screws
« Reply #8 on: March 22, 2020, 03:41:33 AM »

Quote from: Theo link=topic=25200.msg300016#msg300016 date584630203
Carini are still open, just not allowing personal callers

http://www.carinidena.it/

I’ve just heard that Italy has ordered all non-essential business activity and industrial production to shut down for the time being, which likely means that anything accordion-related will be affected.
Logged
C#/D player

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Reedplate gasket and screws
« Reply #9 on: March 22, 2020, 07:48:49 AM »

mselic, I don't know if it means anything or not, but a hugely extrapolated example would be to hold a reedplate, lengthways tightly between your fingers and ping the reed, then compare the sound to holding the plate, in the same orientation, between the jaws of a vice or something similar, and hear the difference of sound produced between the soft mounting and the hard mounting.
It is quite pronounced, and would indicate to me that a gasket does quieten the sound, but what do I know, it's not like it's scientifically proven and documented evidence, is it? Mind, the hard contact of the screws against the plate would ameliorate the difference somewhat, but I don't believe that it would completely overcome the effect of the softness of the actual gasketed joint.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reedplate gasket and screws
« Reply #10 on: March 22, 2020, 08:54:43 AM »

I’m not able to comment on whether screws or wax for reed  fixing makes a difference because I’ve never heard two comparable instruments.  Emmanuel Pariselle’s instruments have screwed reeds on gaskets, some older Hohners have reeds pinned onto leather gaskets.  A few of the highest quality Italian piano accordions also have screwed or pinned reeds.  Some North American built 4 stops have waxed, some screwed on gaskets, and some I’ve seen are waxed and screwed without gaskets.  In theory the latter plan might be best for sound production because you have direct contact between reedplate and block as well as the positive clamping that only screws can provide.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Reedplate gasket and screws
« Reply #11 on: March 22, 2020, 10:22:45 AM »

Yes I would think that the screws, as Theo says, give a better contact with the block.
Take a Jaws Harp (or trump) for example, it doesn't work properly if you have false teeth, as it needs the conductivity from your own teeth into your jawbone to ground it,  so to speak.

SJ
« Last Edit: March 22, 2020, 11:24:42 AM by John MacKenzie (Cugiok) »
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reedplate gasket and screws
« Reply #12 on: March 22, 2020, 11:06:17 AM »

That's not in doubt John,  what is harder to get a handle on is whether the relatively small differences between waxed and screwed reeds makes a noticeable difference. 

In theory, theory and practice are the same, in practice the aren't!  ;)
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Reedplate gasket and screws
« Reply #13 on: March 22, 2020, 04:40:55 PM »

I would say that in my experience and opinion there is no volume difference but there are tonal ones in so far as I have had a few hohners go from gasket to wax ,however this could be a hard statement to justify as age and tuner are important there is  imho a difference if you play to same type boxes together but again thats quite often the case with similar hohners.  You have to do it to see. Hohner must have changed for a reason but waxing must be easier unless you have no experience of it.??

PS Off topic I am locked down in France you need to prepare for whats to come.
« Last Edit: March 22, 2020, 04:43:27 PM by folkloristmark »
Logged
Mark Taylor
Folkloristmark

Graham Wood

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 132
  • Old Fumble Fingers
Re: Reedplate gasket and screws
« Reply #14 on: March 22, 2020, 04:48:35 PM »

I suppose it's down to whether you want the resonance of a vibrating reed to be directly transferred to the reed block. It could well induce undesirable harmonic effects within the reed block and therefore it would be better to dampen this effect with a gasket.

On the other hand a vibrating guitar string needs to transfer it's resonance to the guitar body to maximise the effect of the tone wood and it does this through the bridge which is solidly attached to the guitar body. If you put a gasket between the bridge and the guitar body you will mute the sound and tone of the vibrating string probably inducing a rather muddy sound.

Just my thoughts.
Logged
Graham Wood - Third Planet from The Sun
Hohner Morgane B/C,   Junior Martin 1 Row in 'D' with knobs on top,   Acadian 1 Row in 'C' with more knobs on top.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reedplate gasket and screws
« Reply #15 on: March 22, 2020, 05:11:53 PM »

Graham,  reeds are kind of opposite to strings.  For max sound output you need to hold the reed plate as rigidly possible so that that vibration is not transferred from the reed tongue to anything. You want the energy to stay in the vibrating reed so that it puts maximum energy into chopping the air stream which is how sound is generated.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

fc diato

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 146
Re: Reedplate gasket and screws
« Reply #16 on: March 22, 2020, 06:38:12 PM »

Would it be any use to test just with one reed? 

If so:
I have just enough Olovisc and exactly 2 of the right screws. (Sorry, i don't have more than these tidbits)
 If interested in doing a test, you can PM me - I'm in Ottawa.
The price?  Letting us know the results! (oh, and eventually returning the precious, precious screws.)
Logged
fc diato

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Reedplate gasket and screws
« Reply #17 on: March 22, 2020, 08:05:04 PM »

I am aware that some of the early Hohners at the top end of the range had their idividual plates screwed on to leather gaskets. This was sold ( I have seen the Hohner blurb 1920's???) as being for longevity / robustness. I think their "Ironclad" (USP "built like a battlehip") for the US market (?) had this feature.

My (1926?) Wilkinson Excelsior - manufactured in Wuttenburg hs screwed in plates.

In terms of how they might perform the gasket is a order of magnitude less rigid than the wood of the blocks and the wood of the blocks an order of magnitude less rigid than the metal of the screws and reed plates.
As the screws are tightened they will clamp down on the gasket which will both yield and spread the load across the perimeter of the reed plates. the screws  hold reed plates down positively whereas wax only gives a passive resistance to vibration.
I have no idea how this might affect sound quality.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Reedplate gasket and screws
« Reply #18 on: March 22, 2020, 08:39:54 PM »

the screws  hold reed plates down positively whereas wax only gives a passive resistance to vibration.
I have no idea how this might affect sound quality.
Not sure that wax is passive, it holds pretty good and when waxed the reed plate is in direct contact with the reed block, unlike gasketed. Also its held by the complete perimeter of the plate versus point load of the screw.

This topic got me thinking, this could be dangerous!

On my beltuna the reeds on the standing block don’t appear to have any wax or gasket at the bottom, I copied this on my box (no wax ) on the base when installing the standing reeds ( some may have found its way over during the waxing process?). I made sure they where down tight to the sound board. I don’t notice any difference between the two boxes or feel like mine is leaky at all.

So does this make sense for sound transmission?
I think the reed being in contact should make some difference. Speaking as a builder it’s distributed load.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Reedplate gasket and screws
« Reply #19 on: March 22, 2020, 09:01:39 PM »

By passive I mean wax isn't under stress when the instrument isn't being played- There are dynamic loads on the reed plates when the instrument is being played - on push notes the reedplates are pushed onto the block by air pressure. On pullnotes the vacuum in the bellows tends to pull reeds away from the reed bocks.

Screws by comparison actively press the reedplates onto the reedblocks.
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal