Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Pokerwork reed blocks interchangeability  (Read 1321 times)

0 Members and 1 Guest are viewing this topic.

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Pokerwork reed blocks interchangeability
« on: March 24, 2020, 10:35:03 PM »

Will a set of 60s GC reed blocks fit a 6 year old DG without needing an overwhelming amount of work (and skill)? I'm hoping the answer is yes but...if not, how hard is it?
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pokerwork reed blocks interchangeability
« Reply #1 on: March 24, 2020, 10:50:20 PM »

There are some potential differences.
1 Gasket on reed block or fondo.
2 The clamp plate is probably different and may need a height adjustment which is usually easy by packing if too low or cutting away wood if too high
3 the “toe” at the opposite end from the clamp may be slightly too loose or too tight. Also an easy fix by shimming with paper or card if loose, or sanding down if tight.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

baz parkes

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1894
    • All Blacked Up
Re: Pokerwork reed blocks interchangeability
« Reply #2 on: March 25, 2020, 11:45:20 AM »


3 the “toe” at the opposite end from the clamp may be slightly too loose or too tight. Also an easy fix by shimming with paper or card if loose, or sanding down if tight.

In my admittedly limited experience the tool of choice has been a Park Drive packet...
Logged
On the edge of Cheshire's Golden Triangle, apparently...

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pokerwork reed blocks interchangeability
« Reply #3 on: March 25, 2020, 12:16:41 PM »

If the Park Drive packet is too thick try a Rizla packet, the packet not the papers.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

baz parkes

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1894
    • All Blacked Up
Re: Pokerwork reed blocks interchangeability
« Reply #4 on: March 25, 2020, 01:13:58 PM »

If the Park Drive packet is too thick try a Rizla packet, the packet not the papers.
Which of course should be used for checking the action at the 12th fret of your guitar...
Logged
On the edge of Cheshire's Golden Triangle, apparently...

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Pokerwork reed blocks interchangeability
« Reply #5 on: March 25, 2020, 02:52:43 PM »


3 the “toe” at the opposite end from the clamp may be slightly too loose or too tight. Also an easy fix by shimming with paper or card if loose, or sanding down if tight.

In my admittedly limited experience the tool of choice has been a Park Drive packet...

Unfortunately I gave up Parkie plains about 40 years ago.I seem to remember it was as hard as when I stoppped completely, twenty years later.

Thanks for the advice, everyone. I've decided to go for it.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Pokerwork reed blocks interchangeability
« Reply #6 on: March 25, 2020, 03:49:58 PM »

I've just stuck my BC poker work set in my Erica, so I could do a sound file and it took about 2 minutes. Mostly shimming the bass blocks so the bent retainers had something to press on.
GC going back in now.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Pokerwork reed blocks interchangeability
« Reply #7 on: March 25, 2020, 05:42:34 PM »

Reeds are on their way. How hard can it be.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Pokerwork reed blocks interchangeability
« Reply #8 on: April 04, 2020, 12:13:27 PM »

The reed blocks turned up promptly, as promised.
Very tidy they look, too. Thank you Brian.
Now I have a dilemma I have been mulling over since they turned up.

I have two 2 row Hohner boxes, one an old 1930's CF, which I think might be an Erika, but I'm not sure (grey marbled plastic, not pretty, but I love the sound). H reeds.
The other, a 6 year old Chinese DG pokerwork. Chinese reeds that sound ok, but without the presence of the H reeds.

Comparing the GC blocks, with the CF blocks, both sets have a lot in common.
      i) Most critical dimensions are identical, including height and reed spacing.
     ii) They both have felt gaskets fitted to the blocks.

They also have key differences (pun intended).
      i) The base plate on the GC blocks are thicker (4.5mm v. 3.5mm), preventing it from sliding under the lip of the rebated block on the other end to the clamping plate.
      ii) The GC base plates are slightly longer, by about 1.5mm.

Comparing the GC blocks with with the DG blocks. They have lot in common.
      i) The overall dimensions of the wooden base plates are very similar, maybe identical.

And some key differences.
      i) The blocks heights and their clamping arrangements are different. The older blocks have clamping clips that hold down the top of the blocks. The newer ones have clamping plates that sit on wooden shims glued to the ends of the blocks.
     ii)  The DG blocks don't appear to have any gaskets on the base plates or the fondo. With the felt gakets, the GC bases are about 1mm thicker than the DG bases.

So, between the three sets of blocks, I seem to have all the possible issues identified by Theo. All easy fixes, but:
      i) Which instrument do I put them in? Definitely easier to slip into the CF than the DG, but I really like playing the CF. The pokerwork is more, or less, a backup for when my main instrument is off for service, etc.
     ii) Do I modify the blocks, or the mounting arrangements in the boxes? Or, a mixture of both?
    iii) If I modify the GC blocks to fit in the DG  do I remove the felt gasket completely (scrape it off)? Will I be able to get a good seal without a gasket?
     iv) Or, would I be better off removing material from the base plates, with something like a flat iron orbital sander (which I have, it has no dust bag), or would this make them too thin and subject to failure?

With both options, is there a real danger that if, I sand them, I'll never get rid of the dust?

Anybody any thoughts?
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pokerwork reed blocks interchangeability
« Reply #9 on: April 04, 2020, 01:10:05 PM »

Can’t answer all the questions but here are two:

If you decide to take the felt gaskets off blocks most should peel off leaving a residue of bits of felt and glue.  Don’t use your orbital sander on this.  It doesn’t have a big enough flat surface to ensure you end up with a perfectly flat base to the re ed block.  Use a sheet of fairly coarse abrasive paper glued onto a piece of flat material like 18mm plywood or similar. Rub the base of the block onto that by hand and it should clean up quickly and easily.

If you think one of your boxes is an Erika with a K it will have an extra half row of 4 buttons and a different design of reed block.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Pokerwork reed blocks interchangeability
« Reply #10 on: April 04, 2020, 01:50:33 PM »


If you think one of your boxes is an Erika with a K it will have an extra half row of 4 buttons and a different design of reed block.

Thanks Theo. Advice noted. I'm tempted to leave the gasket on and thin the base plate down. It will leave the timber at the end 2.5mm thick. My gut feeling is that should be ok, with a slight nagging doubt.

It's not an Erika, then. No helper row. I looked in the 1929 catalogue, but they are completely different. Picture of mine (actually not mine, but identical) attached.
Just Pre-pokerwork?
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

bellowpin

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 119
Re: Pokerwork reed blocks interchangeability
« Reply #11 on: April 04, 2020, 05:02:35 PM »

The reed blocks turned up promptly, as promised.
Very tidy they look, too. Thank you Brian.
Now I have a dilemma I have been mulling over since they turned up.

I have two 2 row Hohner boxes, one an old 1930's CF, 
      i) Which instrument do I put them in? Definitely easier to slip into the CF than the DG, but I really like playing the CF. The pokerwork is more, or less, a backup for when my main instrument is off for service, etc.
     ii) Do I modify the blocks, or the mounting arrangements in the boxes? Or, a mixture of both?
   

Anybody any thoughts?   
        hello greg, glad to see the project is coming along . if you like the CF and ought to keep it , maybe it is time to ask the forum for another box , to receive the " GC transplant "  .  there could be a  C ,C#  pokerwork gathering dust ,in some corner of the internet . each day takes us deeper into " maaddnneess"  .-   a fellow sufferer ,  brian n.
Logged
whole life in the shropshire hills. on the slow track and enjoying it.

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Pokerwork reed blocks interchangeability
« Reply #12 on: April 04, 2020, 06:53:30 PM »

 
hello greg, glad to see the project is coming along . if you like the CF and ought to keep it ,
Definitely.
I am planning on making whatever I do easily reversible, anyway.
Likely to be the DG that gets the treatment. I'll probably just leave the gasket as it is. See if it works.

Quote

 maybe it is time to ask the forum for another box , to receive the " GC transplant "  .  there could be a  C ,C#  pokerwork gathering dust ,in some corner of the internet . each day takes us deeper into " maaddnneess"  .-   a fellow sufferer ,  brian n.

Tempting as that is, my aim is to smuggle  my solution into the house without offering a chance of she, who will remain nameless giving me the third degree. To be fair, my problem is mostly having the space.

Mind you I would like to try a semitone system, just so I have an idea of what people are talking about in related discussions. Maybe when the I make some progress on the GC.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Pokerwork reed blocks interchangeability
« Reply #13 on: April 04, 2020, 08:03:55 PM »

I have a set of C/C# reed blocks from a very tidy early Pokerwork if ever you are inclined.  They are offered in the 'Exchange' post, but I would not be averse to parting with them as the Box now houses a set of CGM D/G ones.  Just the reed blocks are easier to sneak in than a whole Box.  They have felt on the blocks..... ;)
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Pokerwork reed blocks interchangeability
« Reply #14 on: April 04, 2020, 08:18:57 PM »

I have a vague memory of emailing you Nigel, but have no record of it. Did I? If you're selling your blocks I could be interested, depending on price, of course.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Pokerwork reed blocks interchangeability
« Reply #15 on: April 04, 2020, 08:30:01 PM »

I have a set of C/C# reed blocks from a very tidy early Pokerwork if ever you are inclined.  They are offered in the 'Exchange' post, but I would not be averse to parting with them as the Box now houses a set of CGM D/G ones.  Just the reed blocks are easier to sneak in than a whole Box.  They have felt on the blocks..... ;)

Thanks for the offer Nigel. I may well be in the market at a future date but, for now, am going to concentrate on the GC thing.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Pokerwork reed blocks interchangeability
« Reply #16 on: April 04, 2020, 09:30:20 PM »

I have a vague memory of emailing you Nigel, but have no record of it. Did I?

PM sent.....
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal