Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Worn axle holes  (Read 750 times)

0 Members and 1 Guest are viewing this topic.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Worn axle holes
« on: April 17, 2020, 09:43:16 AM »

Can anyone recommend a tried n tested method of tightening up worn axle holes on old wooden keys? They flop about a bit, a common problem on old instruments.
I’m thinking...fill with wood glue and redrill...using the existing hole end as a guide to get new hole centred. Obvs the wear is probably only a 0.1 of a mm.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Worn axle holes
« Reply #1 on: April 17, 2020, 10:12:58 AM »

Any sort of filling like that is problematic because you end up with a tiny film of filler.  Getting that to survive the drilling and reaming process is problematic.  I've found the best way to do this is to fit a slightly thicker axle rod.  If the original is brass then replace it with a good tough steel eg silver steel or stainless steel.  Carini sell various thicknesses of ground steel rod,  stainless steel cycle spokes are another possibility, though they are usually drawn rather than ground so dimensions may be less consistent.  When enlarging the holes its essential to ream the final diameter, not just drill to the final size.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Worn axle holes
« Reply #2 on: April 17, 2020, 10:30:18 AM »

When I came across this problem a few years ago, I made a reamer out of the same rod which I used as a new axle, obviously slightly thicker than the original, and just reamed through the whole lot.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Worn axle holes
« Reply #3 on: April 17, 2020, 11:52:39 AM »

It might be possible to enlarge the holes slightly and then bush them with slices of thin-wall brass tube.  A fair bit of work, I agree, but it would be a long-lasting solution.

Graham.
« Last Edit: April 17, 2020, 02:13:24 PM by GPS »
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Worn axle holes
« Reply #4 on: April 17, 2020, 01:52:18 PM »

I’ve looked into that too. I agree it would be a longer lasting fix.  To get the very small and accurate clearance you would need a very good reamer to get the final size for the bushes to fit the axle rod. Wood really does work surprisingly well, as long as it’s a fairly dense and smooth grained type.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Worn axle holes
« Reply #5 on: April 17, 2020, 02:27:49 PM »

Ok, thanks for that. V helpful. I’d need to ream the holes in the keyboard itself, so I would need to fashion a long reamer.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Worn axle holes
« Reply #6 on: April 17, 2020, 02:29:32 PM »

When I came across this problem a few years ago, I made a reamer out of the same rod which I used as a new axle, obviously slightly thicker than the original, and just reamed through the whole lot.
...hi...how did you get it to cut? I can see some channels on the reamer. Did you machine those in?

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Worn axle holes
« Reply #7 on: April 17, 2020, 04:07:54 PM »

"machine those in?"

You're pulling my leg! I don't have access to any machinery other than the normal drill, sander and grinder of DIY fame. I just filed a trough around it with the edge of a half round file whilst slowly turning the rod, it left a cutting edge on the rod which was sharp enough, it seems. I actually did the levers separately by placing the reamer in the vice and working the lever up and down it.
Mind you, the axle was nothing fancy, just a bit of plated gas welding rod. The box cost me £15, IIRC.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal