Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Custom Saltarelle  (Read 2807 times)

0 Members and 1 Guest are viewing this topic.

Helena Handcart

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2452
  • Saltarelle Nell
Custom Saltarelle
« on: May 24, 2020, 06:55:40 PM »

This little beauty was posted on Facebook yesterday. It's really not my colour but I do think it is stunning.  It got me wondering about the possibility of getting an aftermarket custom paint job done on a box where the paint finish has perhaps seen better days.  Has anyone done something similar and can share advice?

In the meantime, you can drool over the lovely Salty a little longer.
Logged
Saltarelle Le Romané  | Saltarelle Nuage | Oakwood | various elderly Hohners

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Custom Saltarelle
« Reply #1 on: May 24, 2020, 07:00:59 PM »

I have sprayed a number of boxes with Halford Car Enamel rattlecans, not too difficult but if I were to do it again I would follow up with coats of lacquer to make the surface more hard wearing.


eg The Pokerwork of Death

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Custom Saltarelle
« Reply #2 on: May 24, 2020, 07:06:40 PM »

I'd really like to try hydro dipping


https://www.youtube.com/watch?v=z22gDHPdrHs

Helena Handcart

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2452
  • Saltarelle Nell
Re: Custom Saltarelle
« Reply #3 on: May 24, 2020, 08:06:27 PM »

I have sprayed a number of boxes with Halford Car Enamel rattlecans, not too difficult but if I were to do it again I would follow up with coats of lacquer to make the surface more hard wearing.


eg The Pokerwork of Death

From memory the Pokerwork of Death has quite a matt finish.  I like the way the wood shows through a little on the coloured Saltarelles, I also like the light gloss finish - I'm assuming that could be achieved with a wood stain and lacquer perhaps? 
Logged
Saltarelle Le Romané  | Saltarelle Nuage | Oakwood | various elderly Hohners

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Custom Saltarelle
« Reply #4 on: May 24, 2020, 08:11:45 PM »

Any colour you can get a good wood-stain in - and they are many and varied and on occasion 'lurid' ! - you can finish with Tru-oil for a finish like that ?  Paint would lose the grain, which is a shame on real wood, especially if it is 'good' wood.

The fingerboard on my P/work Walnut jobbie is an original black one, rubbed down and stained and finished with Tro-oil ( as is the walnut skin )  Any wear just needs a wipe over with wire-wool and re-oiling.

Logged

Jeremy Burnett

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 116
Re: Custom Saltarelle
« Reply #5 on: May 26, 2020, 09:32:10 AM »

Is the walnut the original Hohner construction? If one scraped an old one might one find that wood underneath? I certainly looks lovely.
Logged

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Custom Saltarelle
« Reply #6 on: May 26, 2020, 11:39:25 AM »

No, that started out as one of the celluloid 'marble/cracked ice' effect one's where the plastic had started de-laminating and was cracked and stained in places ( ie. it was rough and fairly cheap !).  I stripped it and veneered it with Walnut.  The original celluloid is effectively just a plastic veneer held on with a glue that smells of Pine forests when warmed to loosen it.  Underneath the celluloid is a typical constructional soft-wood Ply.

There isn't anything complicated about it really. It is all flat surfaces, straight edges and no corners to go around.  It's had all Lester's suggested 'doings' and currently has a set of early A/D reeds in.  I think it plays really well, although arguably, as yet, I don't!

There is no 'stain' on the Walnut, just natural wood and Tru-Oil, after Danish Oil, with an 'on - off' of French Polish to seal it early on. 

I have never 'sacrificed' a Presswood or Pokerwork to see how they are finished, so I don't know if they are 'surfaced' or the impress is direct into the 'carcass'.  They don't seem to 'peel', so possibly not.  They could still be sanded flat I suppose as long as the G-d's of Hohner Past weren't watching.
Logged

Jeremy Burnett

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 116
Re: Custom Saltarelle
« Reply #7 on: May 26, 2020, 03:46:05 PM »

Thanks, I have a pressed wood, It looks , as the name implies, that it has just had the pattern impressed in the wood surface. Not walnut!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Custom Saltarelle
« Reply #8 on: May 26, 2020, 04:13:26 PM »

The wood in most Hohner 2915 types like pokerwork, presswood etc is usually solid wood, except for celluloid finished versions which are usually plywood.

The solid wood is usually a pale coloured hardwood, possibly birch or alder.  I think various species with similar properties  have been used.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Dick Rees

  • Neo-Luddite
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1640
Re: Custom Saltarelle
« Reply #9 on: May 26, 2020, 04:23:01 PM »

The wood in most Hohner 2915 types like pokerwork, presswood etc is usually solid wood, except for celluloid finished versions which are usually plywood...

...which likely accounts for the more lively feel of the PW compared to the Erica.  Good vibrations!
Logged
"You're making the wrong mistakes."
...Thelonius Monk

"I never made one of my discoveries through the process of rational thinking."
...Albert Einstein

"If Art Tatum took up classical music seriously, I'd quit my job the next day."
...Vladimir Horowitz

Helena Handcart

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2452
  • Saltarelle Nell
Re: Custom Saltarelle
« Reply #10 on: May 26, 2020, 04:36:07 PM »

I'm very happy for my Pokerwork(s) to stay Pokerworky, I was thinking more of upgrading the finish on a Saltarelle.
Logged
Saltarelle Le Romané  | Saltarelle Nuage | Oakwood | various elderly Hohners

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Custom Saltarelle
« Reply #11 on: May 26, 2020, 05:19:57 PM »

Have a look at Keda Dye and what guitar makers do with their products.  On a pre-finished/rubbed down 'case' you may not - probably wouldn't - get the same degree of absorption into the wood as if it were bare, but you should be able to get enough pigment in to give the overall effect.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Custom Saltarelle
« Reply #12 on: May 26, 2020, 08:39:17 PM »

Some guitar neck finishes give a coloured but translucent effect. E.g. this stuff...
https://www.rothkoandfrost.com/guitar-making-c83/guitar-finishing-c15#t234:t471:t85
« Last Edit: May 26, 2020, 08:41:39 PM by RogerT »
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Custom Saltarelle
« Reply #13 on: May 27, 2020, 10:01:42 PM »

If the wood grain is nice and the original finish tired anyway, stripping the old finish would allow use of more conventional in-the-wood stain and clear finish.
Logged

Helena Handcart

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2452
  • Saltarelle Nell
Re: Custom Saltarelle
« Reply #14 on: May 28, 2020, 08:48:24 AM »

OK, so here's the thing. I'm pretty hand with DIY. Really quite happy doing basic woodworking, power tools are fun in my world etc.  What I'm not is a craftsman (unless you want a data warehouse, website or perhaps and app).  I also have the attention span of a goldfish. You get the picture.

There's only really one chance to get this sort of project right.  Supposing just for a moment I was actually serious about getting a box overhauled like this - would it be a job for a melodeon fettler or should I look beyond squeezy world for a slightly different skillset?


In case you're wondering it'll be green.
Logged
Saltarelle Le Romané  | Saltarelle Nuage | Oakwood | various elderly Hohners

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Custom Saltarelle
« Reply #15 on: May 28, 2020, 10:02:08 AM »

Martyn White is a qualified French polisher, and Pete Ward at Acorn has done some very nice refinishing on older Castagnaris.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Custom Saltarelle
« Reply #16 on: May 28, 2020, 03:29:32 PM »

There's only really one chance to get this sort of project right.  Supposing just for a moment I was actually serious about getting a box overhauled like this - would it be a job for a melodeon fettler or should I look beyond squeezy world for a slightly different skillset?

Fettlers et al seem to mostly deal with what's going on inside the instrument, I think you would be looking at a different skillset - someone more familiar with finishing woods, potentially furniture types?

However, I wanted to post for a different reason. changing the outward appearance actually does have some significant artistic touches to consider, in addition to the practical concerns of actually doing it. The casework for the Saltarelle linked is very simple. Instruments that were designed with a wood-look of some kind in mind may have eg inlays, panels, etc or other patterns and such like to make them look interesting. Additionally, a fiery maple and rich mahogany are both colourable but will have different results which, to some extent, probably want to be considered with the final look of the box in mind.

We considered our options to have my 3v Oakwood in a nice emerald green, to match my other half's green mandolin, but, we (collectively) decided against it because we weren't really sure how it'd end up and I was already a big fan of the birds eye maple, and as you noted, you only get the one shot typically.

edit - oh, also, guitar people probably. People are always putting/wanting to put crazy finishes on guitars. There might be some helpful knowledge on 'after market' finishes in those communities.
« Last Edit: May 28, 2020, 06:05:33 PM by Gena Crisman »
Logged

Chris Rayner

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 467
Re: Custom Saltarelle
« Reply #17 on: May 28, 2020, 04:38:33 PM »

I think the real current expert craftsmen in this area are car spray painters.  I have no intent of altering the appearance of any of my instruments, but if I were to do so I think I’d speak to an independent car painter.

I agree that the grain of wood is attractive, but tastes differ.  I would probably look for a transparent tinted finish, but if your fancy turns to something more steam punk/goth then there are some fairly wacky finishes available in the custom car pallet.  Candy apple metal flake anyone?  http://www.colormaniapaint.com/candycolors.html
Logged
Elderly amateur musician hoping to stave off dementia by learning to play the melodeon.  Main instrument a Tommy, also D/G and G/C pokerworks,  a single row 2 stop Hohner, and a new addition to the free reedery, a rather splendid Paolo Soprani four voice 120 bass c-system chromatic button accordion.  Very shiny, very loud, and about the same size and weight as a small car.  Now I’ve traded me Benny with (ahem) a cash adjustment, to a three voice 60 bass Castagnari K3.

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Custom Saltarelle
« Reply #18 on: May 28, 2020, 05:23:23 PM »

I'd say the current experts are polishers. Theo has already given two names of people who are as at home inside the box as outside.
All my cabinet making career I have worked closely with a polisher, the last ten years or more sharing a workshop in Newhaven. I've always supplied him with furniture "in the white" and he's done the spraying. You really can't beat a proper furniture finish.
Timbers behave differently as to how they absorb stains, colours and polishes. A spirit stain on softwood looks appalling but an oil stain on oak is likely to look wonderful. A sealing coat before staining is often the way to stop patchy colouring, although the stain won't penetrate the timber. The gloss/semi-gloss or matt coat covers and seals it all in.
There's a lot of skill to this, even more if a previous finish is to be removed first. You can get a really good clear finish as a DIY craftsperson using a variety of polishes and lacquers, but I'd experiment A LOT with matching scrap timber before I'd risk a colour stain. I'd rather hand it to a professional. If all the gubbins inside is removed/masked and the bare ends handed to an experienced polisher, it's not a difficult job, not with the right gear
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Custom Saltarelle
« Reply #19 on: May 28, 2020, 05:59:47 PM »

Yes it’s a job for someone skilled in finishing wood, not metal.   Plenty of musical instrument makers have these skills, and so of course do furniture makers.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal