Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Bass Reed Valve Issue.  (Read 996 times)

0 Members and 1 Guest are viewing this topic.

BobM

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 310
Bass Reed Valve Issue.
« on: June 11, 2020, 11:48:47 AM »

Hi,

I have a buzz on a F bass note on my Sandpiper G/C, which is mainly on the draw but occasionally on the push. I removed the bass unit and it's easy to see that the thin plastic part over the leather valve has a kink in it so it's not laying against the valve properly.

So what would be the fix, either in the short or long term? I'm finding that as I progress to playing more on the C row that the smearing is not helping me at all.

Many Thanks,

Bob.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Bass Reed Valve Issue.
« Reply #1 on: June 11, 2020, 12:30:03 PM »

A kink in the plastic layer is often used as away to apply a little more pressure near the tip to ensure the valve closes fully.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

BobM

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 310
Re: Bass Reed Valve Issue.
« Reply #2 on: June 11, 2020, 01:15:21 PM »

A kink in the plastic layer is often used as away to apply a little more pressure near the tip to ensure the valve closes fully.

It's a kink away from the leather, it looks like an accident judging by the angle.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Bass Reed Valve Issue.
« Reply #3 on: June 11, 2020, 06:02:06 PM »

A kink in the plastic layer is often used as away to apply a little more pressure near the tip to ensure the valve closes fully.

It's a kink away from the leather, it looks like an accident judging by the angle.
Best to replace the valve then. As the valve is on the outside reed plate, it's not a particularly difficult job. No need to remove the reed plate. Just pull the old valve off and carefully clean off any residual adhesive (no need to be obsessive - just so long as the new valve can sit flush). Small tweezers are quite good for removing the old rubbery adhesive.

Use solvent-free contact adhesive to glue the new valve back on. Try to use the same length of glued surface as the previous valve had. This should ensure that the valve lifts by the same amount and will not noticably change the tuning.

Charlie Marshall can supply valves.
http://www.cgmmusical.co.uk/CGM_Musical_Services/Reed_Valves.html
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Bass Reed Valve Issue.
« Reply #4 on: June 11, 2020, 08:27:58 PM »

This valve issue is an interesting one.  I did a re-valve/tune/wax the other day.  I accidentally ( or carelessly  :-[) re-valved a reed pair with a x3 flap one side and a x2 flap valve the other, instead of a matched pair.  In my defence they were from a supplier where the flaps are the same (white) colour! and after all that filing my finger tips are 'shot'.

They were very light plastic valves on a mid sized reed, D4, C5 or the like.  The difference in 'start' speed on the reed was very noticeable, one distinctly following the other.  Valves balanced, problem solved.

That bent plastic flap, makes me wonder if someone has worked on the outward facing reed next to the valve - fine tuning perhaps ? and damaged the valve with their 'blade' support ?  If so the reed next to it might need 'pinging' to re-seat/de-burr if it is marginally off, causing the buzz ?  If there are signs of work at the tip it might explain the bent flap and the buzz ?

I have found reeds can pivot on the rivet and need realigning, or the side of the reed need de-burring even after gentle work.

People who don't make such mistakes may have no experience of such 'gremlins' ::) ;)

 
Logged

BobM

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 310
Re: Bass Reed Valve Issue.
« Reply #5 on: June 12, 2020, 09:13:17 AM »


That bent plastic flap, makes me wonder if someone has worked on the outward facing reed next to the valve - fine tuning perhaps ? and damaged the valve with their 'blade' support ?  If so the reed next to it might need 'pinging' to re-seat/de-burr if it is marginally off, causing the buzz ?  If there are signs of work at the tip it might explain the bent flap and the buzz ?


This is what I think, the fold is very clean, and looks like an accident. Fortunately unknown to me, there's a respected fettler living only half an hour away. Hopefully I'll get him to adjust a couple of higher treble notes that need a little "calming" tremolo wise as well.
Logged

BobM

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 310
Re: Bass Reed Valve Issue.
« Reply #6 on: June 12, 2020, 02:00:34 PM »


That bent plastic flap, makes me wonder if someone has worked on the outward facing reed next to the valve - fine tuning perhaps ? and damaged the valve with their 'blade' support ?  If so the reed next to it might need 'pinging' to re-seat/de-burr if it is marginally off, causing the buzz ?  If there are signs of work at the tip it might explain the bent flap and the buzz ?


This is what I think, the fold is very clean, and looks like an accident. Fortunately unknown to me, there's a respected fettler living only half an hour away. Hopefully I'll get him to adjust a couple of higher treble notes that need a little "calming" tremolo wise as well.

All sorted, and it appears that the rivet was slightly loose as well, and I've also had a slow starting reed fixed as well. All's well that ends, as they say..
Logged

BobM

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 310
Re: Bass Reed Valve Issue.
« Reply #7 on: June 12, 2020, 07:02:21 PM »


That bent plastic flap, makes me wonder if someone has worked on the outward facing reed next to the valve - fine tuning perhaps ? and damaged the valve with their 'blade' support ?  If so the reed next to it might need 'pinging' to re-seat/de-burr if it is marginally off, causing the buzz ?  If there are signs of work at the tip it might explain the bent flap and the buzz ?


This is what I think, the fold is very clean, and looks like an accident. Fortunately unknown to me, there's a respected fettler living only half an hour away. Hopefully I'll get him to adjust a couple of higher treble notes that need a little "calming" tremolo wise as well.

All sorted, and it appears that the rivet was slightly loose as well, and I've also had a slow starting reed fixed as well. All's well that ends, as they say..

Maybe I've spoken too soon. There's still a little rasping that blurs the note, strange because the other bass note are really clear. Maybe they'll get better in time.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal