Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Waxing between reedplates with little to no gap  (Read 3077 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Waxing between reedplates with little to no gap
« on: June 23, 2020, 02:44:36 PM »

I’d like to ask for people’s opinions on how best to wax between reedplates when there is little or even no room between them. I find this is often the case with PAs, where a lot of reeds are crammed tightly together in order to fit. I’ve found examples where they were so close together that it looked as though they hadn’t bothered trying to get any wax in there at all.

In the past I used to apply a bit of melted wax to the side of the reedplate that was already installed and then quickly press the other one in place next to it. I thought this worked brilliantly until I discovered that sometimes the wax pushed through and fouled up the valve on the inside.

I’ve attached photos (or will attach in subsequent post) showing treble blocks where there is still room between the plates, but not much! Trying to get hot wax to flow down between them doesn’t work because the space is too narrow and the wax just cools down partway down the channel. I don’t have photos of the bass block but on that one the plates are pushed up against one another. I’ve also attached a photo illustrating the problem I described above with the wax seeping behind the plate and potentially affecting the valve (this was from factory install).

Suggestions welcome! Thanks!
« Last Edit: June 23, 2020, 02:48:15 PM by mselic »
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Waxing between reedplates with little to no gap
« Reply #1 on: June 23, 2020, 02:59:05 PM »

I think you are doing it the right way.  You just have to be careful to not use too much wax.  One small tip is to place the reed on the block just beyond the hot wax bead, and slide the reed plate towards the previous fixed reed.   This helps to get the wax between the plates rather than under.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Waxing between reedplates with little to no gap
« Reply #2 on: June 23, 2020, 04:39:38 PM »

I have one of these.....similar but slightly different 'nibs' to the one pictured came with mine - one of mine is like a heart shaped 'plate', with an edge that fit's nicely between typical Hohner reed plates.  It is designed, not to 'solder', but to actually melt wax, so it is far less intense.  I get a line of wax between and betwixt tight plates with a small brush then use the tool 'nib' to melt it and meld it into place.  Any of that slightly clogged grainy wax that has cooled on the edge of the plate re-liquidifies and washes between the plates.  Very handy for someone who isn't very handy!  It is excellent for dealing with the oft found 'gremlin' reed that spoils a 'just' re-waxed block and needs easing off, tweaking and putting back in place. 
I have fashioned a 'copper tube' spoon like the commercial ones, that fit's onto the Encaustic tool via one nib ( the wire one ) but that is a work in progress, pending doing another Pokerwork style set.  The idea is to keep the copper tube warm to help the wax flow - if it works.....


https://www.ebay.co.uk/itm/Encaustic-Wax-Art-Stylus-New-Boxed/184336198204?hash=item2aeb4b2a3c:g:iqYAAOSw0theUTWn
Logged

Nigel Champion

  • Member
  • *
  • Offline Offline
  • Posts: 18
Re: Waxing between reedplates with little to no gap
« Reply #3 on: June 24, 2020, 10:53:42 AM »

Has anyone any experience in using one of the fine batik pens to resolve this problem? 

I see Encaustic make/made a flow pen attachment for their low temp soldering irons for wax work:
https://www.amazon.com/Encaustic-Flow-Pen-Batik-Enkaustikos/dp/B000AIILA8

Nigel
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Waxing between reedplates with little to no gap
« Reply #4 on: June 24, 2020, 11:27:02 AM »

Has anyone any experience in using one of the fine batik pens to resolve this problem? 

I see Encaustic make/made a flow pen attachment for their low temp soldering irons for wax work:
https://www.amazon.com/Encaustic-Flow-Pen-Batik-Enkaustikos/dp/B000AIILA8

I tried a batik tjanting stylus once but the wax cools down too quickly for reed work and clogs the tip.  I think they are designed to work with low-temperature melt wax (e.g. soy wax). No good for reed work.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Waxing between reedplates with little to no gap
« Reply #5 on: June 24, 2020, 11:36:15 AM »

Looking back to the OP's photos, I have often waxed reed plates with this sort of close spacing. I use use a temperature controlled soldering iron with a tip which I have filed down to a fine point which easily fits into the narrow gap between the reed plates. The trick is to get the iron fairly hot (approx 180°C) to compensate for the heat-sink effect of the reed plates. Then, using stick-form reed wax, I dribble hot wax along the length of the slot, not too much. Then use the hot iron point to remelt the wax and rock the block backwards and forwards to encourage the wax flow evenly in the slot.

I agree about the method of running a wax bead along the edge of one reed plate and then butting up the next reed plate to it. That works well, but only if you are waxing a set of reed plates. Not so good if you are just re-waxing a single reed plate (due to, say, having removed it to renew the inside valve). Then I would use my narrow soldering iron tip method as described above.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Waxing between reedplates with little to no gap
« Reply #6 on: June 24, 2020, 11:39:49 AM »

I agree about the method of running a wax bead along the edge of one reed plate and then butting up the next reed plate to it. That works well, but only if you are waxing a set of reed plates. Not so good if you are just re-waxing a single reed plate (due to, say, having removed it to renew the inside valve). Then I would use my narrow soldering iron tip method as described above.

Why not Steve?    Just run a bead of wax on each side and place the reed. I've not had any problem with that method, though care is needed to use only the right amount of wax so the underside valve doesn't get contaminated with wax.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Waxing between reedplates with little to no gap
« Reply #7 on: June 24, 2020, 11:51:41 AM »

I agree with Theo. In my very limited experience a fine paintbrush is quite good enough to get a carefully controlled line of wax on the edge of the adjacent plates.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Waxing between reedplates with little to no gap
« Reply #8 on: June 24, 2020, 11:57:52 AM »

Don't agree with you there Pete!   With a fine paintbrush I can't get enough wax in place quickly enough to get the reed plate in place while the wax is still liquid and with enough wax to make the reed secure.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Waxing between reedplates with little to no gap
« Reply #9 on: June 24, 2020, 12:23:05 PM »

I agree about the method of running a wax bead along the edge of one reed plate and then butting up the next reed plate to it. That works well, but only if you are waxing a set of reed plates. Not so good if you are just re-waxing a single reed plate (due to, say, having removed it to renew the inside valve). Then I would use my narrow soldering iron tip method as described above.

Why not Steve?    Just run a bead of wax on each side and place the reed. I've not had any problem with that method, though care is needed to use only the right amount of wax so the underside valve doesn't get contaminated with wax.
Why not? I suppose because I can use my fine-tipped soldering iron method to good effect. But your method works too.  (:)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Waxing between reedplates with little to no gap
« Reply #10 on: June 24, 2020, 12:54:38 PM »

I suppose it’s partly because I’m doing this as a business so I’ve worked hard to find methods which are quick and efficient without losing effectiveness.

As you say if it works for you that’s good.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Waxing between reedplates with little to no gap
« Reply #11 on: June 24, 2020, 02:42:07 PM »

I suppose it’s partly because I’m doing this as a business so I’ve worked hard to find methods which are quick and efficient without losing effectiveness.

As you say if it works for you that’s good.

May I ask what your method is for applying wax to the sides of the reedplate prior to pushing the next one into place?
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Waxing between reedplates with little to no gap
« Reply #12 on: June 24, 2020, 02:59:08 PM »

I use a temperature controlled soldering iron.  I rest a stick of wax against the body of the iron so that a slow flow of melted wax runs off the tip of the iron.  I don’t know of anyone else who uses this method,  but I find it to be fast, efficient and allows me excellent control over placing the wax in a smooth and even bead.  A neat result is important to me.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Waxing between reedplates with little to no gap
« Reply #13 on: June 24, 2020, 03:07:24 PM »

I use a temperature controlled soldering iron.  I rest a stick of wax against the body of the iron so that a slow flow of melted wax runs off the tip of the iron.  I don’t know of anyone else who uses this method,  but I find it to be fast, efficient and allows me excellent control over placing the wax in a smooth and even bead.  A neat result is important to me.
I use this method too. You taught it to me, remember? ;)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Waxing between reedplates with little to no gap
« Reply #14 on: June 24, 2020, 05:09:47 PM »

I use a flat wax spoon and run a small bead then push next reed in place. Too much wax and, yes, it interferes with the reed, so don’t use too much. I always wax in same direction, so the valve is always on the other side. Soldering iron always handy for those odd ones that prove difficult. On some Liliputs I’ve seen, there isn’t any wax between the reeds..and this is obviously how they were fitted in the factory. The fit is very good (they really don’t need to be welded on), and top and bottom wax is good enough, often with an additional tack. Obvs if you can get wax in there then do so, but if the fit is good and you can secure the plate top and bottom, it works in my opinion (and Bandoneon plates are just pinned on with (often) no gasket required. Well that's what I reckon anyway.  (:)

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Waxing between reedplates with little to no gap
« Reply #15 on: June 24, 2020, 06:45:18 PM »

Temp controlled iron with a thin knife tip works a treat and gets in to tight spots just fine.
This shape tip works for me, but you can make any shape to suit as long as it is not too big (dissipates the heat too quickly if too large)

Graham


Logged

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Waxing between reedplates with little to no gap
« Reply #16 on: June 24, 2020, 07:20:10 PM »

What are the benefits of using wax in places where the Hohner didn't consider it necessary when they designed the instrument and the seal is good without it? Isn't it misdirected effort?
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Waxing between reedplates with little to no gap
« Reply #17 on: June 24, 2020, 07:32:17 PM »

What are the benefits of using wax in places where the Hohner didn't consider it necessary when they designed the instrument and the seal is good without it? Isn't it misdirected effort?


Every Liliput I have worked on has had original wax down the sides of the reeds

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Waxing between reedplates with little to no gap
« Reply #18 on: June 24, 2020, 07:47:00 PM »

Same here,  I’ve never seen reeds without wax between  reed plates on an original Liliput, Preciosa or the similar sized small piano accordions.  There’s not very much, but it is there.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Waxing between reedplates with little to no gap
« Reply #19 on: June 24, 2020, 09:14:12 PM »

Thanks. Just wondering. I got a different impression from some of the comments.
Don't ask don't find anything out.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal