Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Waxing between reedplates with little to no gap  (Read 3064 times)

0 Members and 1 Guest are viewing this topic.

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Waxing between reedplates with little to no gap
« Reply #20 on: June 24, 2020, 09:32:19 PM »

One more reason to use the German type waxing spoon or its Italian equivalent (spatula) - the only method used in all accordion factories known to me - rather than the awkward soldering iron. Easier, faster, better result.
« Last Edit: June 24, 2020, 09:37:21 PM by diatonix »
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Waxing between reedplates with little to no gap
« Reply #21 on: June 24, 2020, 09:53:38 PM »

One more reason to use the German type waxing spoon or its Italian equivalent (spatula) - the only method used in all accordion factories known to me - rather than the awkward soldering iron. Easier, faster, better result.
This is undoubtedly true if you are waxing multiple blocks, but for the sort of work a fettler does - single reeds and the occasional full block a soldering iron is more than suitable.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Waxing between reedplates with little to no gap
« Reply #22 on: June 24, 2020, 09:59:04 PM »

One more reason to use the German type waxing spoon or its Italian equivalent (spatula) - the only method used in all accordion factories known to me - rather than the awkward soldering iron. Easier, faster, better result.

Does anyone make and sell this type of waxing tool?
Logged
C#/D player

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Waxing between reedplates with little to no gap
« Reply #23 on: June 24, 2020, 10:21:24 PM »

You could easily make one similar to the one in this video of a skilled craftsmen at work.https://www.youtube.com/watch?v=yjGaLwqrtOs
I did and it would work great if you have the proper heat source, I didn’t. And for me it was controlling the amount of wax that was an issue ( probably best to avoid coffee).  With practice, this method does put the wax where you want it.
I made mine out of a round foam paint brush handle ( used one of course) and a piece of copper bent and soldering to a similar shape.
« Last Edit: June 24, 2020, 10:24:33 PM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Waxing between reedplates with little to no gap
« Reply #24 on: June 24, 2020, 11:27:19 PM »

Besides apparently being a bit of a pain in the ass to wax in, are there any other obvious downsides to packing the reeds this close together? There appears to be ~4 mm gaps between plates on a pokerwork, compared to say, idk I'd guess like 0.5 to 1mm between the plates in the OP?
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Waxing between reedplates with little to no gap
« Reply #25 on: June 25, 2020, 12:24:41 AM »

Due to space limitations, the smaller boxes (Lilliput, Preciosa, Tommy, Lilly, etc.) have the reeds closer together - there's no way around it.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Waxing between reedplates with little to no gap
« Reply #26 on: June 25, 2020, 12:57:42 AM »

One more reason to use the German type waxing spoon or its Italian equivalent (spatula) - the only method used in all accordion factories known to me - rather than the awkward soldering iron. Easier, faster, better result.

Does anyone make and sell this type of waxing tool?

Charlie Marshall sells them:
http://www.cgmmusical.co.uk/CGM_Musical_Services/Reed_Waxing_Tools.html#0

Hohner:
https://www.hohnershop.com/wax-spoon/
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Waxing between reedplates with little to no gap
« Reply #27 on: June 25, 2020, 12:59:17 AM »

Besides apparently being a bit of a pain in the ass to wax in, are there any other obvious downsides to packing the reeds this close together? There appears to be ~4 mm gaps between plates on a pokerwork, compared to say, idk I'd guess like 0.5 to 1mm between the plates in the OP?
Not that I know of. Castaganari treble end reed plates are usually closely spaced. If it's OK for Castagnari... etc.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Waxing between reedplates with little to no gap
« Reply #28 on: June 25, 2020, 01:10:54 AM »

Due to space limitations, the smaller boxes (Lilliput, Preciosa, Tommy, Lilly, etc.) have the reeds closer together - there's no way around it.
And I assume this spacing would rule out a gasket /screw system as a downside, so you must wax?
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Waxing between reedplates with little to no gap
« Reply #29 on: June 25, 2020, 04:54:58 AM »

Spatula gets my vote.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Waxing between reedplates with little to no gap
« Reply #30 on: June 25, 2020, 07:45:01 AM »

And I assume this spacing would rule out a gasket /screw system as a downside, so you must wax?

No, I know of two ways of using screws with close spaced reed plates.  Screws can go at the ends of the reed plates.  The bass reeds on Pariselle boxes are held this way.
In Shand Morinos reed plates are notched part way along each side.  The notches provide just enough space for the retaining screws.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Waxing between reedplates with little to no gap
« Reply #31 on: June 25, 2020, 07:44:29 PM »

And I assume this spacing would rule out a gasket /screw system as a downside, so you must wax?

No, I know of two ways of using screws with close spaced reed plates.  Screws can go at the ends of the reed plates.  The bass reeds on Pariselle boxes are held this way.
In Shand Morinos reed plates are notched part way along each side.  The notches provide just enough space for the retaining screws.
I should have known that there would be a work around, thanks Theo.
I was thinking that there wasn’t going to be enough wood thickness ( between reeds) for the screws also, but I guess it all works then.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Waxing between reedplates with little to no gap
« Reply #32 on: June 27, 2020, 07:11:34 PM »

I do a couple of things, warming the plate before installation helps keep the wax from cooling to quickly, laying a thin bead down and sealing the side of the reed next to the one you are installing works pretty well.
I also make a heated brass blade tool I sell, this can be filed down to a knife edge to get between plates. https://www.ebay.com/itm/Heated-accordion-reed-waxing-iron/193282388610?hash=item2d00873282:g:8iYAAOSwCDxeDVIE
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Dave Praties

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 195
Re: Waxing between reedplates with little to no gap
« Reply #33 on: June 27, 2020, 10:39:36 PM »

As Theo says, there are ways of using screws on closely spaced reeds. This is my approach. Did it many years ago, and am now repeating the process on a newly acquired Liliput.
After cleaning up the block, glue small pieces of timber on either side of the block where the screw goes. This way, you can drill the divider and put in the screw without it splitting. On the current instrument, I am also gluing similar pieces at the top of the aperture as I am re-tuning to D/G by moving the reeds down one position.
The reed plated need a very tiny notch filing on either side to clear the screw.
Finally, (but not on the photos), Olivisc gasket will be fitted.
The reinforcing does not interfere with the reed or valve, and is substantial enough to enable the screw to hold well.
Logged
Castagnari Handry 18 G/C. Castagnari Handry 18 D/G.    Self-built G/C 2.5/12 bass. almost finished after 7 years! Bb/Eb Preciosa. C/F Lilliput.
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal