Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Metal pallets  (Read 1668 times)

0 Members and 1 Guest are viewing this topic.

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Metal pallets
« on: June 26, 2020, 02:30:11 PM »

I have an old box, with metal pallets, which look to be tack welded on to metal arms, and it has a wooden action. The treble buttons are up and down like Grampians. How on earth do I level up the buttons, and yet keep the pallets flat on the fondo, other than by detaching the pallets?

Sir John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Metal pallets
« Reply #1 on: June 26, 2020, 02:43:28 PM »

No need to detach the pallets.
To lower the button height, hold the pallet firmly against the fondo, making sure that it can't slip up or down as well as being unable to lift. Then gently push down on the button to lower it. The metal arm should bend slightly and when released the button should be just a frazzle lower.
To raise the button height, similarly hold the pallet firmly in position and then gently bend the lever arm upwards a tiny bit.

If you have held the pallet in position firmly, it should still seal properly on the fondo vents, with no air leaks.

Precautions:
Ensure that the pallet arm weld is firm on the pallet.
Ensure that the metal lever arm cannot break the join at the point where it enters the wooden arm. Usually a hole in the end of the wooden arm.

It's probably best to use two pairs of round nose pliers to do the lever arm bending, one to bend the other to support. Above all, go gently, bit by bit.

if, despite your precautions, a pallet does become detached, you should be able to reattach it using hot-melt glue.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Metal pallets
« Reply #2 on: June 26, 2020, 05:54:57 PM »

If it was mine I would adjust one button at a time to the required height,then if the pallet needed adjusting, cut it loose with a dremel then glue back on with hot glue. You said they were only tacked on so this should be easier than messing about for ages bending the arms.  Also you might be lucky in that they might not all need adjusting if you manage to hold the pallet flat to the fondo while pressing the button.  Good luck - John.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Metal pallets
« Reply #3 on: June 26, 2020, 09:25:12 PM »

I had this problem on a 1930s PA. The pallets were made of Bakelite with a metal bracket, which was soldered onto the arms. The pallets tended to break up as I removed them, so I made new pallets from wood, then waxed them back on once I’d set up the keyboard.  I’ve given up using hot glue to attach pallets...prefer to use reed wax as I find it easier to apply (with a flat spatula)...though the arm does need to locate into a groove in the pallet.

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Metal pallets
« Reply #4 on: June 26, 2020, 09:57:06 PM »

Some years ago I re-padded the bass pallets on my old Paolo Soprani. I then used hot glue to fix the pallets back on the round metal levers.
I now find that the pallets are swivelling on the levers thus causing all sorts of problems.
This is a working box so I have temporarily blanked off the reed-blocks in order to carry on playing gigs (remember those?).
I would like to re-instate the basses so ..... any ideas?
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Metal pallets
« Reply #5 on: June 26, 2020, 10:44:01 PM »

The problem is that the levers are round -  so you need to file a "flat" or solder on an extra blob to give the hot glue something to grab on to - or both  -  a flat on the pallet side and extra metal on the upper side .You didnt say if the pallets had the usual groove  in which case it would be easier to grind a flat on each side of the lever and lock it in the groove. A patch of material on the top of the lever helps to lock it in place. 
QUICK FIX..... SUPER GLUE - just dont glue the pallets to the fondo!
                Good luck -   John.
Logged

Jon Stapleton

  • Member
  • *
  • Offline Offline
  • Posts: 44
Re: Metal pallets
« Reply #6 on: June 26, 2020, 11:14:36 PM »

I had a koch where they were actually soldered.  If yours is like this it is fairly straightforward.
Get button height about right then just heat the joint with the soldering iron. They just suddenly level up
  I did burn a couple of facings but just took the opportunity to replace them    Hope this helps
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Metal pallets
« Reply #7 on: June 27, 2020, 01:02:35 AM »

Quote
Some years ago I re-padded the bass pallets on my old Paolo Soprani. I then used hot glue to fix the pallets back on the round metal levers.
I now find that the pallets are swivelling on the levers thus causing all sorts of problems.
This is a working box so I have temporarily blanked off the reed-blocks in order to carry on playing gigs (remember those?).
I would like to re-instate the basses so ..... any ideas?

On an old box I have, the metal levers were sandwiched between 2 discs of leather (with hide glue I think) for a semi-flexible joint.  Maybe something along these lines with a modern adhesive ??  Great way to recycle old curly leather valves, if nothing else !  :D   
« Last Edit: June 27, 2020, 04:13:51 AM by tirpous »
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Metal pallets
« Reply #8 on: June 27, 2020, 03:23:30 AM »

Very interesting, Tirpous!
Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Metal pallets
« Reply #9 on: June 27, 2020, 10:14:21 AM »

The leather flexi joint is used inside some bandoneon. Nice idea. And I also found that hot glue can fail as Rees describes...hence my giving it up.
« Last Edit: June 27, 2020, 10:31:29 AM by RogerT »
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Metal pallets
« Reply #10 on: June 27, 2020, 07:02:56 PM »

I found that you want a high wattage soldering iron to remove or just the soldered on pallets.
I have a 35 watt one that I get a nice bead of solder on then press the bead to the arm right on top of the solder spot. putting a side load on the pallet so it slides off the second the solder melts is good so you don't heat it more than it needs to be.
Low temp solder for jewelers works well for reassembly as it won't burn the felt if you are doing a leveling job. https://www.esslinger.com/low-temp-solder-tix-for-watch-and-jewelry/?gclid=EAIaIQobChMIz47n18mi6gIVlh6tBh0tgg2vEAQYAyABEgJwFfD_BwE
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal