Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3   Go Down

Author Topic: 'Dedic' tuning on LMMH with fixed stops  (Read 5790 times)

0 Members and 1 Guest are viewing this topic.

JohnAndy

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 244
  • John Barber
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #20 on: July 02, 2020, 10:50:54 AM »

Thanks for sharing that, Steve, it's very clear and informative :-)

I checked a random sample of your numbers, and my calculations agree with yours, so I must have remembered some of my school maths after all!

Just one little question, which I'm sure is of academic interest only, as the differences involved are so small, but...

When the human ear hears the note produced by the two slightly out-of-tune reeds, at what pitch does it hear the combined note?

Does it hear the average Hz value of the two sounds? Or does it hear a pitch half way between the two, in terms of cents? Or something else? Or maybe it is just impossible for anyone to hear accurately enough to determine this in a test?

If, for sake of an example, we hear a half-way pitch in terms of cents, then it looks like your C3 should sound 0.2 cents flat overall. Admittedly, that's a tiny difference - but is it possible to detect this, do you happen to know?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #21 on: July 02, 2020, 11:01:55 AM »


If, for sake of an example, we hear a half-way pitch in terms of cents, then it looks like your C3 should sound 0.2 cents flat overall. Admittedly, that's a tiny difference - but is it possible to detect this, do you happen to know?

Highly unlikely that a human could detect that difference, not even by listening for a beat between two notes. The beat period would be of the order of 30 seconds if I have my mental arithmetic about right.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #22 on: July 02, 2020, 12:16:27 PM »


... Does it hear the average Hz value of the two sounds? Or does it hear a pitch half way between the two, in terms of cents? Or something else? Or maybe it is just impossible for anyone to hear accurately enough to determine this in a test?

If, for sake of an example, we hear a half-way pitch in terms of cents, then it looks like your C3 should sound 0.2 cents flat overall. Admittedly, that's a tiny difference - but is it possible to detect this, do you happen to know?
Yes - you are correct that the ear ought to perceive a pitch which is mid-way between between the two reeds. In practice, that 'ought' depends on factors such as whether the two reeds are both sounding at the same volume (amplitude), that the harmonic spectrum of each reed is identical (highly unlikely!), and I suspect other factors too. However, in practical terms, the mid-way pitch idea works.

Quote
If, for sake of an example, we hear a half-way pitch in terms of cents, then it looks like your C3 should sound 0.2 cents flat overall

Not sure where you get that from, as the overall percieved pitch is always the mean value of the two frequency values, not cents values.
In the case of C3 the perceived pitch will be (128.813 + 132.813)/2 = 130.813 = exactly the C3 frequency

The cents values on the spreadsheet will be subject to a rounding error as they are only quoted to 2 decimal places. with more decimal place accuracy, the rounding error will disappear. If you can distinguish 0.2 cents, you have a better ear than me! Also my Peterson tuner will only read to a precision of 0.1 cent, so the spreadsheet values to 2 decimal places is more than adequate for practical use.

Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #23 on: July 02, 2020, 12:19:29 PM »

Highly unlikely that a human could detect that difference, not even by listening for a beat between two notes. The beat period would be of the order of 30 seconds if I have my mental arithmetic about right.
Not sure you have that right Theo. For the note C3 my spreadsheet values will still give you a beat frequency of 4 Hz. But perhaps I have misunderstood your comment?
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #24 on: July 02, 2020, 12:48:54 PM »

I wasn’t clear.  I meant if you have two notes with 0.2 cents difference.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #25 on: July 02, 2020, 12:52:41 PM »

I wasn’t clear.  I meant if you have two notes with 0.2 cents difference.
OK thanks!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #26 on: July 02, 2020, 12:58:57 PM »

For people who like to visualise numerical data (I do!), I've created an Excel chart of the data in my earlier spreadsheet, which shows the inverse exponential ratios of the cents offsets vs higher pitch to give a 4 Hz tremolo rate.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

JohnAndy

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 244
  • John Barber
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #27 on: July 02, 2020, 01:52:34 PM »

Not sure where you get that from, as the overall percieved pitch is always the mean value of the two frequency values, not cents values.
OK, that's exactly what I was asking, so you've answered my question, thanks. I was asking specifically about whether perceived pitch would be the mean of the frequency values or of the cents values.

Had it been the cents values, then the mean of -26.67 and +26.27 (for the note C3) would be -0.2 cents, which is why I suggested the note might sound very slightly flat.

But, as you say that the perceived pitch is the mean of the frequency values, then perceived pitch should then be bang in tune.
Logged

JohnAndy

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 244
  • John Barber
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #28 on: July 02, 2020, 02:00:15 PM »

Highly unlikely that a human could detect that difference, not even by listening for a beat between two notes. The beat period would be of the order of 30 seconds if I have my mental arithmetic about right.

Thanks Theo - I won't be losing any sleep about that amount of out-of-tuneness then ;-)

My Python script calculates that if we play C3 vs C3 - 0.2 cents then we will get a beat only about every 66 seconds!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #29 on: July 02, 2020, 02:13:31 PM »

Oh well I got the right order of magnitude!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #30 on: July 05, 2020, 10:59:11 PM »

You can easily detect a 1Hz pitch difference between two tones at 10kHz sounded together because you're not detecting pitch, you're detecting amplitude changes -- such a pitch change is completely undetectable with only one note sounding.

You might be able to hear the beat between 9,999Hz and 10,000Hz. Some of us would be deliriously happy to hear anything at 10kHz.
Me too, probably -- I was of course speaking figuratively, and using the Yorkshire "you" instead of the posh RP "one" ;-)
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #31 on: July 06, 2020, 03:26:14 PM »

To give a more thorough update, and to answer my own question, I can report back that using Viennese tuning on a 4-stop LMMH accordion (with fixed stops) *DOES* sound different than using the more standard tuning, and I'm not just referring to the overall perceived pitch.

For the sake of reference, the box had previously been tuned with the two M reeds at 440 - 442, then 440-443, and finally 440-441, with the LH reeds always being at 440.  I began by tuning the two M banks of reeds to approx 439.5 - 441 (I say approximate, because I use the Hz as a reference point only, and then adjust as necessary by ear to achieve the desired rate of tremolo increase). This gave the sound of the box a little more 'bite', but then when I went further and did a true Viennese tuning of equal offset (439 - 441), I was surprised to find that the box suddenly sounded much more civilized, and lost that 'edge' or 'bite' that increased tremolo usually adds.  It certainly didn't sound the same as when it was originally tuned 440 - 442, even though technically the amount of tremolo would be the same in both cases.  Some might find this to be a positive development, but I wasn't happy with it. It's almost as if the Viennese tuning 'neutralized' the richness or depth of sound the box had (I say this in reference to the full LMMH sound only, not MM alone). I decided to go a little further and tuned it to 439 - 442, making sure that there was no longer an equal offset.  The box 'came alive' again but didn't sound as harsh as when it had previously been tuned 440 - 443, once again even though there was the same amount of tremolo in both cases.

Anyhow, I'm sharing this in case anyone finds in instructive.  It certainly was interesting for me!
« Last Edit: July 06, 2020, 03:33:49 PM by mselic »
Logged
C#/D player

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #32 on: July 06, 2020, 03:35:01 PM »

To give a more thorough update, and to answer my own question, I can report back that using Viennese tuning on a 4-stop LMMH accordion (with fixed stops) *DOES* sound different than using the more standard tuning, and I'm not just referring to the overall perceived pitch..... etc.

Matt, that's all really interesting and definitely worth bearing in mind for the next time I tune a 1-row 4-stop box. Your conclusion that asymmetric M-/M+ offets make the box 'come to life' is valuable! Thanks for posting!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #33 on: July 06, 2020, 04:10:08 PM »

Thanks, Steve. Those are my subjective observations only, of course. Others may find the sound of equal offset in such a box to quite pleasant and preferable, or they might disagree with my conclusions/opinions entirely!
Logged
C#/D player

windybutton

  • Member
  • *
  • Offline Offline
  • Posts: 32
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #34 on: July 08, 2020, 03:35:26 PM »

Great ! thanks for the chart Steve,
cheers
Roy
Logged

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #35 on: July 08, 2020, 11:47:48 PM »

I wonder what a wider symmetric tremolo would have done, compared with those other observations.
E.g. 438/442
(in the interests of giving it more "bite" without making it sound out of tune...)
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #36 on: July 09, 2020, 03:45:43 AM »

But maybe the "bite" comes from the out-of-tuneness...
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #37 on: July 09, 2020, 07:47:56 AM »

I wonder what a wider symmetric tremolo would have done, compared with those other observations.
E.g. 438/442
(in the interests of giving it more "bite" without making it sound out of tune...)
I'm fairly sure I've read about it somewhere, but I can't quote the reference, sorry. But as I recall, the argument for an asymmetric tuning for M- M M+ is that it avoids the possibility of phase-locking of the beats which might occur if the M- M offsets were the same as the M M+ offsets. An asymmetric tuning results in an overall more complex sound (not necessarily wetter), as there are more than one set of beats occuring, giving a 'shimmer' sound rather than straightforward beats.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #38 on: July 09, 2020, 09:21:33 PM »

An asymmetric tuning results in an overall more complex sound (not necessarily wetter), as there are more than one set of beats occuring, giving a 'shimmer' sound rather than straightforward beats.

Yes, that makes sense. I was forgetting the context of having an M reed (Or L, in this case) and hence two separate beats.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: 'Dedic' tuning on LMMH with fixed stops
« Reply #39 on: July 10, 2020, 10:51:28 AM »

I wonder what a wider symmetric tremolo would have done, compared with those other observations.
E.g. 438/442
(in the interests of giving it more "bite" without making it sound out of tune...)
I'm fairly sure I've read about it somewhere, but I can't quote the reference, sorry. But as I recall, the argument for an asymmetric tuning for M- M M+ is that it avoids the possibility of phase-locking of the beats which might occur if the M- M offsets were the same as the M M+ offsets. An asymmetric tuning results in an overall more complex sound (not necessarily wetter), as there are more than one set of beats occuring, giving a 'shimmer' sound rather than straightforward beats.

If it's of any interest, I also looked at 2 MM reeds vs. 3 MMM reeds when I was investigating tuning. I also found that symmetric tuning (equal M- M M+) didn't work very well, with any slight differences you got a not very pleasant slow beating -- and in reality I'm sure you'd get the phase-locking problem, which is what can make soem notes on 2-reed boxes sound nasty if there isn't a cross-brace between the reed blocks.

Changing the offsets to keep concert pitch on average but with different beat rates for the two sides (e.g. -4Hz +1Hz +3Hz) removed this problem and did give the more complex "shimmery" sound that Steve referred to. Interestingly, the lack of distinct peaks and dips in the volume meant that if anything it didn't sound as loud to the ear as a 2-reed MM setup -- this also agrees with my finding that bringing in an L reed does fill the sound out but can actually reduce apparent volume compared to MM because it "fills in the gaps".

It's fascinating what you find out when you start looking into how the human ear actually detects and interprets sound -- you'd think that adding a third reed (M or L) would make a box louder, but there are good reasons why this isn't always the case to the ear, even if though an SPL meter says it's louder. Which explains why a wetter-tuned two-reed MM box -- preferably Dedic-tuned, obviously ;-) -- is the instrument of choice when you want to be heard in noisy environments, like playing for Morris outdoors. Or some sessions... ;-)
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses
Pages: 1 [2] 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal