Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Bellows Frame Material  (Read 3275 times)

0 Members and 1 Guest are viewing this topic.

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Bellows Frame Material
« on: July 03, 2020, 09:31:36 PM »

I feel like this has been covered before but I think the suggestions that are usually UK based don't always translate to the availability or price of north american wood; where softwood is king. I have a few woodworking friends who hoard off cuts of various hardwood and wondered what would be optimal? Otherwise I might start cutting up the coffee table.hah
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Bellows Frame Material
« Reply #1 on: July 03, 2020, 09:34:49 PM »

In the UK 'brown furniture' ie mahogany etc is available at very low cost, due to being right out of fashion, in our equivalent to your thrift stores. Once broken up it supplies a fine selection of aged hard woods.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Bellows Frame Material
« Reply #2 on: July 03, 2020, 09:40:47 PM »

Almost any reasonably tough and fine grained hardwood that is well seasoned and stable will serve. Beech, maple, sycamore or something similar.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Bellows Frame Material
« Reply #3 on: July 03, 2020, 10:17:20 PM »

Red oak would be fine.
Cheap and easily obtainable.
We used to use it for repro furniture.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Bellows Frame Material
« Reply #4 on: July 03, 2020, 10:52:21 PM »

Almost any reasonably tough and fine grained hardwood that is well seasoned and stable will serve. Beech, maple, sycamore or something similar.
Good woods to use, but get a new blade if you cut these  >:E
How about cherry or poplar easy to mill and cherry is very stable as I’ve mentioned before.
Also pretty available. Some think of poplar as a softwood but its a hardwood on the softer end and very easy to mill and stable enough.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Bellows Frame Material
« Reply #5 on: July 04, 2020, 01:45:57 AM »

What type of frame are you making ?  I don't think a softwood would be ideal for Hohner-style small frames held with pins, but it would be fine (and a weight saver) for the larger frames typical of many 1-row boxes.
Logged

Jon Stapleton

  • Member
  • *
  • Offline Offline
  • Posts: 44
Re: Bellows Frame Material
« Reply #6 on: July 04, 2020, 02:14:00 AM »

I'm with Theo  beech, maple, ash   oak is a little coarse, popular, nothofagus any Acer or lime would be perfect. Basically what he said..close grained hardwood.
Logged

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Bellows Frame Material
« Reply #7 on: July 04, 2020, 04:47:52 AM »

Wow, thanks gang. There is a flat bit of frame that needs to run parallel to the folds and then the square tubing that will mate to the box sides and take the pins. I'll suggest these wood ideas to my mates who know more about wood than this guy.

Cheers
Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Bellows Frame Material
« Reply #8 on: July 04, 2020, 04:57:15 AM »

I use lime (aka linden or basswood in the US,I believe) simply because I have quite a lot of it. I bought half a ton or so of offcuts from a closing down furniture factory years ago to use mainly for carving.  It's strong, stable, light and has very unobtrusive grain.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Bellows Frame Material
« Reply #9 on: July 04, 2020, 08:34:02 AM »

If you live in the US I can mail you enough to do the job 5x over for the cost of shipping in a variety of woods. A friend runs a cabinetry shop and generates tons of stick scrap, I heated my wood stove with it for several weeks when I was up there and threw several hundred lbs of it in my truck.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Bellows Frame Material
« Reply #10 on: July 04, 2020, 08:47:50 AM »

Inner frame: no matter what kind of wood you use,  make sure that the pin holes run through the fibers rather than between them.
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Bellows Frame Material
« Reply #11 on: July 04, 2020, 09:52:21 AM »

I've used cherry and yew.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Frank Pallister

  • Good talker
  • **
  • Offline Offline
  • Posts: 62
Re: Bellows Frame Material
« Reply #12 on: July 04, 2020, 10:16:00 AM »

American walnut is  cheap and widely available and good enough for banjo necks !
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Bellows Frame Material
« Reply #13 on: July 04, 2020, 12:31:22 PM »

Inner frame: no matter what kind of wood you use,  make sure that the pin holes run through the fibers rather than between them.
Good point!
Wood has a face grain and edge grain and an end grain the last not being relevant here.
I think your saying don’t run it through the edge grain, correct?
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Bellows Frame Material
« Reply #14 on: July 04, 2020, 03:53:10 PM »

Inner frame: no matter what kind of wood you use,  make sure that the pin holes run through the fibers rather than between them.

That makes total sense. As mentioned, I have a few friends who are really skilled with woodworking which means that I don't have to flex my head too much over this. I generally do metalwork or some other kind of trade with them for their craft. Finding the right material without spending a bunch at the hardware store is the challenge. I like Lester's idea of breaking up "brown furniture".
Logged

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Bellows Frame Material
« Reply #15 on: July 04, 2020, 04:24:21 PM »

I fancy ramin might be usable too, and is widely available as mouldings, and some of the shapes are damned nearly spot on for bellows frames ;)

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Bellows Frame Material
« Reply #16 on: July 04, 2020, 04:26:52 PM »

I fancy ramin might be usable too, and is widely available as mouldings, and some of the shapes are damned nearly spot on for bellows frames ;)

SJ

I thought that was the cheap noodle packs that eat in college
Logged

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Bellows Frame Material
« Reply #17 on: July 04, 2020, 04:33:10 PM »

Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Bellows Frame Material
« Reply #18 on: July 06, 2020, 09:02:53 PM »

I have some American white oak offcuts that I bought 20 yrs ago to build a library. It’s like iron now, so working it needs a super sharp blade. It has quite a fine grain. Just putting a screw in it requires exactly the  right sized predrilled hole, otherwise it’s easy to strip the screw head. Someone gave me an old bed board, which was stained but when cut up revealed itself as beech, and very nice timber to work with (fine grain again). I've made a set of pallets with it, among other things. It makes good keyboard buffer strips too. But Lester's observation is A1. And old furniture store is a great place to source decent timber (we have one in Andover...it’s like Aladdin's cave inside).

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Bellows Frame Material
« Reply #19 on: July 07, 2020, 02:11:54 AM »

I have some American white oak offcuts that I bought 20 yrs ago to build a library. It’s like iron now, so working it needs a super sharp blade. It has quite a fine grain. Just putting a screw in it requires exactly the  right sized predrilled hole, otherwise it’s easy to strip the screw head. Someone gave me an old bed board, which was stained but when cut up revealed itself as beech, and very nice timber to work with (fine grain again). I've made a set of pallets with it, among other things. It makes good keyboard buffer strips too. But Lester's observation is A1. And old furniture store is a great place to source decent timber (we have one in Andover...it’s like Aladdin's cave inside).
I’d use white oak before red oak for sure.
Speaking of pallets sometimes good wood can be found in the wood use to make pallets for material handling and or lumber yard bunking blocks if you can see the possibilities under the dirt and rough sawn material.  I’ve made several nice decorative boxes out of crap.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal