Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: cracked pallet arm  (Read 2601 times)

0 Members and 1 Guest are viewing this topic.

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
cracked pallet arm
« on: August 12, 2020, 09:38:11 PM »

im restoring a nice old international (dienst) 4 stop single row and one of the brass arms that holds one of the pallets has a crack. fortunately its not come apart completely but its not far off. the crack is right where the screw goes into the pallet. anybody managed a successful fix. im thinking solder maybe with an extra brass small plate to add extra strength. but maybe just soldering would work? anybody know? and if so what is correct solder and flux and is it a job for a soldering iron or a hot flame? im familiar with soldering things like jack plugs with a soldering iron and soldering plumbing joints with a torch but bever had to fix a brass pallet arm. im looking for a permanent fix as its to be used rather than put on a shelf. arm has to bent to shape once new pallet leather and felt are glued on so joint has to be strong and ideally flexible. anybody out there can tell me the proper fix? its lasted 100 years though which aint bad is it!
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: cracked pallet arm
« Reply #1 on: August 12, 2020, 10:40:31 PM »

A picture could be helpful.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: cracked pallet arm
« Reply #2 on: August 12, 2020, 10:46:46 PM »

I think soft solder might be a temporary fix at best.  Silver solder would be very strong.   I may be able to help you with a replacement.  I have a 2row International  box which I’ve used fir spares.  Is it the triangular section arm? 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: cracked pallet arm
« Reply #3 on: August 12, 2020, 11:05:28 PM »

im restoring a nice old international (dienst) 4 stop single row and one of the brass arms that holds one of the pallets has a crack. fortunately its not come apart completely but its not far off. the crack is right where the screw goes into the pallet. anybody managed a successful fix. im thinking solder maybe with an extra brass small plate to add extra strength. but maybe just soldering would work? anybody know? and if so what is correct solder and flux and is it a job for a soldering iron or a hot flame? im familiar with soldering things like jack plugs with a soldering iron and soldering plumbing joints with a torch but bever had to fix a brass pallet arm. im looking for a permanent fix as its to be used rather than put on a shelf. arm has to bent to shape once new pallet leather and felt are glued on so joint has to be strong and ideally flexible. anybody out there can tell me the proper fix? its lasted 100 years though which aint bad is it!
Tinmans solder -or solder for electrical work will do fine.
Are you sure the pallet arms are brass though? I have an International with gilded pallet arms which I suspect are iron underneath. Assuming it's brass you are dealing with, then provided thecrack surfaces are fresh enough for the solder  to bond flooding the crack with solder  is likely to be a permanent solution.
Like you I have never tackled this job, but I would try to do it with a red hot soldering iron - the old type of soldering iron that you heated up on the gas stove. Clean surfaces are critical to  strong soldering but you can't get into the crack. next best thing, smear flux all over the crack area and bring the solder wire behind the foot of the pallet  Approach with the iron from the other side. The red hot iron flashes the tip of the solder wire .  Melts it instantly and floods the crack.
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: cracked pallet arm
« Reply #4 on: August 12, 2020, 11:17:11 PM »

I think soft solder might be a temporary fix at best.  Silver solder would be very strong.   I may be able to help you with a replacement.  I have a 2row International  box which I’ve used fir spares.  Is it the triangular section arm?
I am curious about how you would get the pallet arm out of the key lever.....not hand to do it yet. But I've got five 2 row internationals ....one of which is the spares depot for the rest.

As Diatonix says -a photo would help
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: cracked pallet arm
« Reply #5 on: August 13, 2020, 09:38:56 AM »


Tinmans solder -or solder for electrical work will do fine.


Have to disagree on that Peadar.   Tinman's or electrical solder has very little mechanical strength.  If there are stresses sufficient to crack brass (or steel) then a soft solder repair will be much weaker than the original and is unlikely to last.   
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: cracked pallet arm
« Reply #6 on: August 13, 2020, 01:08:47 PM »

pictures attached as soon as i can figure out how to reduce to right size. sorry meant to add them last night. 2 of the cracked arm and 1 of the side of the international. im pretty sure its brass. the crack goes all the way across the screw hole. when i removed the pallets there were 19 original screws and 1 rogue screw. 19 dome head and 1 tiny countersunk. i guess thats what weakened it. such a small thing to cause the issue! i have a couple of international two rows that are also in the queue for restoration but the arms are too short or too long so i guess a replacement arm would have to be from a scrap single row. im guessing the triangular arm is glued into rocker. hopefully with hide glue if it does turn out i can find a replacement arm. but did some reading up on internet and model makers say brass soldering with the right flux and right solder and enough heat can be quite strong. but the question remains..strong enough? that little brass arm takes a lot of punishment over the course of a few tunes!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: cracked pallet arm
« Reply #7 on: August 13, 2020, 01:23:24 PM »

Hard solder (aka silver solder) works very well on brass, and is pretty much equal in strength.  I’ve used it to put new tops on Lachenal concertina buttons.  I used a paste made of a flux and solder powder combined which is very easy to use.  Supplier https://www.hswalsh.com/categories/silver-solder
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: cracked pallet arm
« Reply #8 on: August 13, 2020, 01:30:09 PM »

pictures attached hopefully
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: cracked pallet arm
« Reply #9 on: August 13, 2020, 01:34:09 PM »

close up of arm
« Last Edit: August 13, 2020, 01:35:41 PM by chris hall »
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: cracked pallet arm
« Reply #10 on: August 13, 2020, 01:46:02 PM »

Hard solder (aka silver solder) works very well on brass, and is pretty much equal in strength.  I’ve used it to put new tops on Lachenal concertina buttons.  I used a paste made of a flux and solder powder combined which is very easy to use.  Supplier https://www.hswalsh.com/categories/silver-solder
so like this? https://www.google.com/search?client=firefox-b-d&q=using+silver+solder+paste#kpvalbx=_9TQ1X8jlDMLB8gLkxo3oBQ34
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: cracked pallet arm
« Reply #11 on: August 13, 2020, 02:56:40 PM »

Mind, that looks useful, Chris!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: cracked pallet arm
« Reply #12 on: August 13, 2020, 04:03:42 PM »

That’s it.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: cracked pallet arm
« Reply #13 on: August 13, 2020, 04:15:57 PM »

That’s it.
im excited. i get to buy some flux/silver solder ive not tried before and a torch thing i can also use for lighting barbeques and chargrilling steaks. bring it on. looks easy. what could possibly go wrong. then just got to finish renewing pallet leathers and tweaking springs and tuning and it'll be good to go.  i'll report back! thanks guys for your help. fingers crossed!
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: cracked pallet arm
« Reply #14 on: August 13, 2020, 08:07:42 PM »

That’s it.
im excited. i get to buy some flux/silver solder ive not tried before and a torch thing i can also use for lighting barbeques and chargrilling steaks. bring it on. looks easy. what could possibly go wrong. then just got to finish renewing pallet leathers and tweaking springs and tuning and it'll be good to go.  i'll report back! thanks guys for your help. fingers crossed!

What could possibly go wrong.....you are joking aren't you?
what wuld worry me a bout silver solder is the risk of setting something alight with the blow torch....shellac  varnishes are notoriously flammable and the make up of historic ones is an unknown quantity. A foam fire extinguisher should see  you right and probably won't do too much damage to the box if youu do actually have to use it.
Apart fom that I empathise wth your excitement.

I have a "Wypper patent" 2 row that I need to get started on- pallet leather in hand but what glue are you using? I had considered evo stick contact ahesive or I could use pearl glue. You are obviously into the pallet refaacing stage and guidance on best practice for these boxes would be useful.

Finally - I hope  you are going to keep a record of the existing tuning of the box before you start re tuning. The old Dienst boxes appear to have been originally set up in a  variety of tunings, which generally appear to have remained reasonably stable. I have one which is either an A=430 C#/D (which is how I choose to read it) or an Old High Philharmonic pitch C/C# (more likely).

And let us hear what she sounds like when job's done. (:)
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: cracked pallet arm
« Reply #15 on: August 13, 2020, 08:34:42 PM »

That’s it.
im excited. i get to buy some flux/silver solder ive not tried before and a torch thing i can also use for lighting barbeques and chargrilling steaks. bring it on. looks easy. what could possibly go wrong. then just got to finish renewing pallet leathers and tweaking springs and tuning and it'll be good to go.  i'll report back! thanks guys for your help. fingers crossed!

What could possibly go wrong.....you are joking aren't you?
what wuld worry me a bout silver solder is the risk of setting something alight with the blow torch....shellac  varnishes are notoriously flammable and the make up of historic ones is an unknown quantity. A foam fire extinguisher should see  you right and probably won't do too much damage to the box if youu do actually have to use it.
Yes, I set fire to a button on an old club II and I don't have a spare.
It burned surprisingly easily.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: cracked pallet arm
« Reply #16 on: August 13, 2020, 08:36:51 PM »

I use one of those wee pen blowtorches, very controllable, and localised heat too,

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: cracked pallet arm
« Reply #17 on: August 13, 2020, 11:56:39 PM »

That’s it.
im excited. i get to buy some flux/silver solder ive not tried before and a torch thing i can also use for lighting barbeques and chargrilling steaks. bring it on. looks easy. what could possibly go wrong. then just got to finish renewing pallet leathers and tweaking springs and tuning and it'll be good to go.  i'll report back! thanks guys for your help. fingers crossed!

What could possibly go wrong.....you are joking aren't you?
what wuld worry me a bout silver solder is the risk of setting something alight with the blow torch....shellac  varnishes are notoriously flammable and the make up of historic ones is an unknown quantity. A foam fire extinguisher should see  you right and probably won't do too much damage to the box if youu do actually have to use it.
Apart fom that I empathise wth your excitement.

I have a "Wypper patent" 2 row that I need to get started on- pallet leather in hand but what glue are you using? I had considered evo stick contact ahesive or I could use pearl glue. You are obviously into the pallet refaacing stage and guidance on best practice for these boxes would be useful.

Finally - I hope  you are going to keep a record of the existing tuning of the box before you start re tuning. The old Dienst boxes appear to have been originally set up in a  variety of tunings, which generally appear to have remained reasonably stable. I have one which is either an A=430 C#/D (which is how I choose to read it) or an Old High Philharmonic pitch C/C# (more likely).

And let us hear what she sounds like when job's done. (:)


good point about fire risk......fingerboard unit will be off when i do it so less risk. mmm wonder if i should extract arm from rocker. that could open up a whole new world of issues unless it comes out easily with a bit of coaxing. i usually use pva to attach felt/leather to pallets. i guess back in the day it would have been pearl/hide glue. ive recently been using titebond genuine hide glue on wood repairs. really easy to use and reversible like the old stuff. that might work too but in any case when it comes to the time to remove and replace pallet facings a sharp knife does the trick. alas it was tuned in the 80's before i got it but i think i got the guy (ivor Hyde) to keep it close to original. as it stands now it seems to be tuned with a tremelo on the mids (one mid row sharp/one mid row flat)i always do a chart before i do any tuning. you never know when you might want to look back at such things. it needs tuning but im going to try and resist the temptation to go too far. as it stands it has a sound you rarely come across these days. i too have a couple more internationals that i need to tackle. one in C/C# and another in C#/D. 
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: cracked pallet arm
« Reply #18 on: August 13, 2020, 11:59:17 PM »

I use one of those wee pen blowtorches, very controllable, and localised heat too,

SJ

good idea. i'll try that!
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: cracked pallet arm
« Reply #19 on: August 14, 2020, 08:38:35 AM »

"good idea. i'll try that!"

Exactly what I thought! But, after a little research, it seems that the strongest silver solder paste doesn't flow until it reaches something like 750 degrees C, and the output of the little pen things (well, the one I was looking at, anyway) is only 400. Make sure it's up to the job before you lash out your tenner or whatever!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal