Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: exasperated and befuddled...  (Read 3672 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
exasperated and befuddled...
« on: September 02, 2020, 09:48:21 PM »

I'm writing in the hopes that someone can maybe cast some light on a problem that has me truly perplexed.  Recently a friend brought me a small, 22 key, single-voice piano accordion (A Carbonari, made in Castelfidardo, about the size of a Castagnari Tommy or smaller) to look over and fix up.   Some of the notes were off, a few of the keys stuck, but for the most part it sounded OK.  A quick glance inside showed me that the wax and valves needed replacing, so I told him I could do that, tune it up, fix the keyboard and that it would be a piece of cake.

I stripped away all the old wax, removed all the old valves, taking care to scrape away any and all glue and/or remnants of the old valve.  The reeds all appeared to be in good shape with no rust or any other signs of trouble.  I carefully cut and glued new leather valves, taking great care to ensure that when I pressed the new valves into place that no glue seeped over and made contact with the reed tongues (a mistake that has occurred in the past which compromises the tuning of the reed).  I always do a very thorough and clean job with this, and all was as it should be.

The first sign of trouble came when I went to wax the reeds back in place; I pinged a few of the bass reeds to make sure I had the right ones going in the right place, only to discover that the pitch of those reeds had changed dramatically in a few places.  Unsure of what to make of it, I only lightly waxed those few reeds in place so that I could make changes if necessary.  I waxed all the remaining treble and bass reeds in place.  When I went to begin tuning the treble side, I was shocked to discover that most of the reeds were *WIDELY* out of tune within the same plate.  For example, an E reedplate (PA reeds being unisonoric - same note on both push and pull) might sound as 20 cents FLAT on the push, and 30 cents SHARP on the pull!  I went along the keyboard and discovered that the majority of the reeds were out like this.  Some were uniformly sharp or flat (both sides of the plate were nearly equally sharp or flat) and some were out of tune in opposite directions as in the example of the E reedplate.  These reeds were not like this when the instrument was brought to me.  I went and inspected the reedplates carefully and could find no signs of trouble.  I pulled some of the plates out and *extensively* examined them, and could find nothing to explain such a drastic and sudden change in pitch.  The tongues themselves could be 'pinged' while out of the box and it was clear that they were as out of tune there on the workbench as they were when waxed in place in the box.

What on earth could be going on?  I'm completely befuddled!
« Last Edit: September 02, 2020, 09:51:15 PM by mselic »
Logged
C#/D player

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: exasperated and befuddled...
« Reply #1 on: September 03, 2020, 01:27:31 AM »

I think you have discovered the new pitch of the reeds arising from new valves and new wax. Changing the valves and renewing the wax can affect the pitch because (a) the rigidity of the reed plates has been changed, but more likely (b) because the properties of the valves have changed - i.e. different flexibilty, sound absorbtion, and amount of lift.

Are you absolutely sure that your own-made valves are really the right thickness, weight, etc.? Personally, I would only ever use commercially available valves, but I know also that you are an experienced and consciensious worker. Other than checking the valve lift and the security of the new wax, there is not a lot you can do other than retune the reeds.

Just be sure to measure the pitch of the reeds in situ in the fully assembled instrument first of all, so you are sure of each pitch correction needed. Then go ahead with the retuning, preferably in situ in the box, if possible. 20 - 30 cents difference is not too much to deal with, and retuning by that sort of amount shouldn't compromise the reeds so long as you are careful.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: exasperated and befuddled...
« Reply #2 on: September 03, 2020, 04:34:21 AM »

Weeeeeell, I finally found out what was going on...after wracking my brain for hours, I finally had an epiphany earlier this evening and put the theory to the test when I got back home.  I'm unhappy to report back that I was correct.  For the sake of posterity, I will share my story of shame here...

Normally, I use contact cement for vinyl valves, but a while ago I followed someone's suggestion on here and started using superglue for leather valves.  I tested this first, and found it to work quite well.  Just a little dab spread evenly on the bottom section of the valve and held in place for a few seconds did the trick every time without any fuss.  I was always very clean and never had any trouble.  If needed, the valves and superglue could easily be removed...a little too easily.  I was concerned that over time the superglue might fail, so I decided this time that I would press and hold the valves into place a little longer, about 5-10 seconds each, ensuring proper adhesion.  I was very careful to to use the glue sparingly to avoid any potential seepage onto the adjacent tongue, and I ensured that this was the case by keeping a close eye on the process.  However, it turns out that a very small amount of glue, almost too small to be noticed with the naked eye, had seeped down and made contact with the corner of the *underside* of the reed tongue that it was covering, unbeknownst to me.  This affected the pitch of the reed, and could only be rectified with very careful and thorough cleaning/scraping of the corners where contact had been made.  The process of correcting this is **miserable** and time consuming, I'm now discovering.  To make matters worse, removing the new valves and the glue that attached them is nearly impossible as the adhesion was a little too good.  What a nightmare...

It seems to me that my decision to press and hold the valves in place for an extended period of time resulted in the glue running downwards and contaminating the reed, something that had never happened to me before.  Nevertheless, I won't be using superglue for the adhesion of leather valves ever again. For someone who always takes great pride and care in my work, I'm somewhat ashamed that I created this mess myself.  Live and learn, I guess.  It will be a costly mistake for me, but at least happened on such a small accordion (and one belonging to a very close friend) rather than a client's PA with 400+ reeds!!  It is completely repairable, but it'll be a real bugger.

Soooo...does anyone have any recommendations on how best to scrape away valve/glue remnants that are *very well* adhered to the reedplate?

PS - Steve, the leather valves I used are from Charlie Marshall.  When I said I cut them, I meant that I had trimmed them lengthwise, and occasionally width-wise, to fit the reedplates.  They are not homemade.
« Last Edit: September 03, 2020, 04:36:13 AM by mselic »
Logged
C#/D player

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: exasperated and befuddled...
« Reply #3 on: September 03, 2020, 08:22:23 AM »

Weeeeeell, I finally found out what was going on...

Soooo...does anyone have any recommendations on how best to scrape away valve/glue remnants that are *very well* adhered to the reedplate?

PS - Steve, the leather valves I used are from Charlie Marshall.  When I said I cut them, I meant that I had trimmed them lengthwise, and occasionally width-wise, to fit the reedplates.  They are not homemade.

Well, at least you have discovered the cause! Superglue is very fluid, as you have now discovered. This is good in some uses, but not for attaching valves. Use contact adhesive in the future!

Try using acetone for removing superglue. You could use nail-polish remover but it is an expensive way of buying it. Industrial grade acetone is very cheap and readily available. Best to do a google-type search for suppliers on your side of the pond.

I would strip off all the reed plates from their wax; use a blunt blade to gently score around the edge of the reed plate so that you can at least retain some of the new wax on the wood of the reed block.

Then soak the reed plates in a bath of acetone - use a shallow, non-plastic, flat bottomed container and just use enough acetone to cover the reed plates. You will probably need to do just a few at a time. Leave to soak for a few minutes and then clean off wax and, hopefully, glue, using a stiff brush - a brass suede brush is ideal. You will need to renew the acetone periodically as it becomes saturated with wax/glue. Do all this in a well-ventilated place, away from any sources of ignition. 

Drain off spent acetone solution into a glass bottle and keep in a safe place until you have finished the job, then take it outside to a safe place into a metal bin or similar and carefully set fire to it; it will burn very vigourously with large flames, so do be very careful. It's good for starting bonfires! Don't pour acetone, spent or otherwise, into drains or into the soil. 

Thanks for the clarification about the source of the leather valves. You should be OK with that.

Good luck!
« Last Edit: September 03, 2020, 08:25:47 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: exasperated and befuddled...
« Reply #4 on: September 03, 2020, 08:47:45 AM »

Not that it helps now, but a point re. S/Glue - which as Steve says is ( in it's usually acquired form ) very viscous - it can be obtained as used by double glaziers in a 'thick' / gloopy consistency which would overcome that problem of it running.

I am 'mourning' the loss of Bostik's 'Solvent Free" clear which was commonly available in the Uk for a protracted period and has been 'discontinued' by the company for some inexplicable, probably EU rule related reason.  It was the best adhesive for fixing leather/plastic to wood & metal by far and incredibly easy to work with.  Dark blue tube, green Gecko logo, "Solvent Free clear".  Odourless, came out white, went clear and rubbery, held brilliantly, but could be scraped off with a thumb nail if needs be.  They ( and others ) have adhesives with similar descriptions, but none seem to compare for use and effectiveness.

I don't think it was ever available in the States.  Nothing else I have found comes close.  Just saying in case anyone has a case.   
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: exasperated and befuddled...
« Reply #5 on: September 03, 2020, 09:07:31 AM »

... S/Glue - which as Steve says is ( in it's usually acquired form ) very viscous -
I think you meant low viscosity? That's what I meant anyway. The ordinary stuff you buy in little plastic bottles is very fluid and its composition also seems to enhance capilliary action, which is why it seeps readily into joints and gaps.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: exasperated and befuddled...
« Reply #6 on: September 03, 2020, 09:14:13 AM »

I have been using Gorilla Super Glue Gel, which is a bit more viscous, although not for valves, I shall stick too (Tee hee) Bostik for that job.

Sir John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Grumpy

  • Grumpy
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 134
Re: exasperated and befuddled...
« Reply #7 on: September 03, 2020, 09:51:15 AM »

Most large DIY stores have superglue remover (same shelf as the superglues). This quickly reduces the glue to a liquid which is capable of being flushed away with solvent. About £3 a small bottle. Regards Chris D
Logged
Chris D, Surrey, UK
Getting old but still learning. Pokerwork G/D, Saltarelle L'Elfique G/D, Castagnari Lilly G/D and Hohner Liliput Declubed G/D + English concertinas, mandolins, recorders, tin whistles and other items unknown to household managment

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: exasperated and befuddled...
« Reply #8 on: September 03, 2020, 10:13:47 AM »

I'm surprised that you're having trouble removing super-glued valves and glue residue from the plates. I've just used a very narrow wood chisel, which seems to have been very successful.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Little Eggy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 843
Re: exasperated and befuddled...
« Reply #9 on: September 03, 2020, 12:07:06 PM »

When I read some Melnet threads a little voice on one shoulder says "Go on...you should have a go at fettling!"

Then I read threads like this one and a voice on the other shoulder says "You??  Fettling?   Don't be silly! You don't have the brains, knowledge, dexterity, tools, time or patience!!!"
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: exasperated and befuddled...
« Reply #10 on: September 03, 2020, 01:08:06 PM »

I'm surprised that you're having trouble removing super-glued valves and glue residue from the plates. I've just used a very narrow wood chisel, which seems to have been very successful.
That's not so good when the superglue has seeped into the very tight space at the rivet end of the reed tongue. That is the problem here.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: exasperated and befuddled...
« Reply #11 on: September 03, 2020, 01:15:00 PM »

Most large DIY stores have superglue remover (same shelf as the superglues). This quickly reduces the glue to a liquid which is capable of being flushed away with solvent. About £3 a small bottle. Regards Chris D
Usually the remover is acetone based. It's a lot of money to pay if you are already going to use acetone as your flushing solvent. As a guide, the last lot of acetone I bought cost me about £6 plus shipping, for a litre of the stuff.

Here's where I get mine:
https://www.mbfg.co.uk/acetone.html
« Last Edit: September 03, 2020, 06:34:14 PM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Grumpy

  • Grumpy
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 134
Re: exasperated and befuddled...
« Reply #12 on: September 03, 2020, 02:51:22 PM »

Did'nt take cost of solvent into account as I normally steal the wifes nail polish remover, its mainly acetone with a touch of purfume. Chris D
Logged
Chris D, Surrey, UK
Getting old but still learning. Pokerwork G/D, Saltarelle L'Elfique G/D, Castagnari Lilly G/D and Hohner Liliput Declubed G/D + English concertinas, mandolins, recorders, tin whistles and other items unknown to household managment

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: exasperated and befuddled...
« Reply #13 on: September 03, 2020, 04:21:35 PM »

When I read some Melnet threads a little voice on one shoulder says "Go on...you should have a go at fettling!"

Then I read threads like this one and a voice on the other shoulder says "You??  Fettling?   Don't be silly! You don't have the brains, knowledge, dexterity, tools, time or patience!!!"

Don't be daunted, Little Eggy -it's just a mistake, and a learning experience!  I've tuned and re-valved thousands of reeds, and this is the first time this has happened.  My mistake was in changing the way I did something without testing it first. In this case it also led to my decision to abandon a product that I was using, even though I've not had troubles with it in the past.  This is the evolution towards better and better practices.  You can bet that this won't happen again ;)  I share my experiences here in case someone else can benefit from it.
Logged
C#/D player

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: exasperated and befuddled...
« Reply #14 on: September 04, 2020, 09:43:17 PM »

Exactly, one learns through mistakes - preferably somebody else's! No matter what the subject, the most detailed "how to" may not quite get through.  This thread tells us not only about the perils of using superglue for this application, but gives a greater understanding of the type of preferred glue and the limits of where it should be applied.  Ver useful, perhaps even to those experienced fettlers who have not suffered this misfortune.

Rob.
Logged

Andy

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 159
Re: exasperated and befuddled...
« Reply #15 on: September 05, 2020, 12:48:21 PM »


I am 'mourning' the loss of Bostik's 'Solvent Free" clear which was commonly available in the Uk for a protracted period and has been 'discontinued' by the company for some inexplicable, probably EU rule related reason.  It was the best adhesive for fixing leather/plastic to wood & metal by far and incredibly easy to work with.  Dark blue tube, green Gecko logo, "Solvent Free clear".  Odourless, came out white, went clear and rubbery, held brilliantly, but could be scraped off with a thumb nail if needs be.  They ( and others ) have adhesives with similar descriptions, but none seem to compare for use and effectiveness.


Solvent free vs solvent based.
I know a lot has been said about adhesives in this and other threads but there is one aspect of this I'm still not clear about.
I can see the attraction of solvent free - much less likely to damage plastic valves.
The thing that concerns me is about solvent free is that this presumably means water based, so I would be worried about reed corrosion. It's definitely the case that water based PVA wood glue left to dry on woodworking tools will cause rust at an alarming rate.
The whole adhesive thing is of course always complicated by different names and products in different parts of the world, the same product with different names and different products with similar names. Then if like Nigel.H you find your favoured product - it gets discontinued.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: exasperated and befuddled...
« Reply #16 on: September 05, 2020, 01:24:17 PM »

I'm quite happy using solvent based contact adhesive for valves. I must have fitted tens of thousands of valves.  If I use a new adhesive, or a new type of valve I'm always on the lookout for solvent damaged to the valve material, I've not seen any recently.  Ive used the solvent free stuff too, but found that it tends to dry up in the tube before it's all used.  The stuff I use now comes from Carini and is sold by them for applying valves, though the actual tube that it comes in says its for leather work!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: exasperated and befuddled...
« Reply #17 on: September 05, 2020, 04:44:42 PM »

I've tried using contact adhesives, but they're so b****y messy! Bits of stringy stuff all over the place with trying to get it onto both surfaces; I've given up and gone back to superglue. I find that by dipping the valve into a droplet, then wiping most of it off, saves it getting where I don't want it to go. (So far!)
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: exasperated and befuddled...
« Reply #18 on: September 05, 2020, 05:04:38 PM »

I've tried using contact adhesives, but they're so b****y messy! Bits of stringy stuff all over the place with trying to get it onto both surfaces;

I know the instructions for contact adhesive say apply to both surfaces,  but for valves it’s quite sufficient to apply it to one surface.  With practice and a good technique I am able to avoid any stringy bits of glue.  Here is an example of a block I’ve just finished.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: exasperated and befuddled...
« Reply #19 on: September 05, 2020, 05:18:26 PM »

I'm quite happy using solvent based contact adhesive for valves...

Are we talking Evostick here?
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal