Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Lockdown project - flat mounted MMM bc  (Read 1227 times)

0 Members and 1 Guest are viewing this topic.

Gav Wood

  • Good talker
  • **
  • Offline Offline
  • Posts: 99
Lockdown project - flat mounted MMM bc
« on: September 25, 2020, 08:22:10 PM »

Well, here we are winston, lockdown project, i aimed to get a box to take in my work bag when going away so needs to be light and small. BC tuned, 16 key, top b key missing as there is a reversal on the b row, 3rd button on c row is the c/d giving full Usable range of a 21 key.

It was built onto the liliput bellows. The frame And fondo is a magazine file from ikea, bass fondo a bit of hardboard from a picture backing at present. All the rest is scrap wood i had lying around.

I had the pallets unchamfered to start with thick leather and foam, but thought the chamfer and thin leather pads work better, not deadening any sound, the pallets are so close together, About 14mm centres on the holes in the fondo (205mm over 16 holes)

The reeds are a mix of piano accordion reeds, i think italian, some are stamped scandalli, but the majority If not all have the 3 face rivets, and all of similar if not the same manufacture. Anyone that knows what they are, let me know, they came in a box of reeds on frames, bought off ebay 20 years ago or so for peanuts, third full box i have had from them. The reeds are mounted flat tip to hole, with a pin located to stop the valve from going through the hole.

There is a chimney block in the middle for the middle reed. I experimented with mml but this mmm sounded better, the l reeds fitting would have been a real squeeze aswell.

Springs, pins and steel rods are from an old pa, Buttons are from a bit of delrin i had leftover from something else.

May yet make a full bass end, but not yet decided. I think i need it out with other people before i decide.

Outside below

Logged

Gav Wood

  • Good talker
  • **
  • Offline Offline
  • Posts: 99
Re: Lockdown project - flat mounted MMM bc
« Reply #1 on: September 25, 2020, 08:43:34 PM »

The chimney is a push fit, quite tight with a gasket on the inside. No other fixing, stays in place could not move much anyway due to bellows frame.
Reeds upto a tone apart are mostly tuned from the central note, more than a tone i have cut them down the middle and glued back together. The bottom note only has 2 reeds on the push to fit the chimney, i dont use that note. All reeds are narrowed, some of the low reeds had to be cut down the centre to lose the width in addition to sides.
Chimney and internal reed mounts are made from maple, i had lots of offcuts already thicknessed To 1.5mm sitting in the loft.
All reeds are mounted by fitting reed to plate, gluing a sliver to the block on one end to trap the end of the reed then screwing the other end. There is also some flexible low strength glue used sparingly.

Tuning was interesting.
Logged

Gav Wood

  • Good talker
  • **
  • Offline Offline
  • Posts: 99
Re: Lockdown project - flat mounted MMM bc
« Reply #2 on: September 25, 2020, 09:10:00 PM »

May be a bit wet, not sure.
https://youtu.be/9ftThV3MRBY
Does need tuning again, but this is pretty much where i put it, middle slightly sharp.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Lockdown project - flat mounted MMM bc
« Reply #3 on: September 25, 2020, 09:41:50 PM »

May be a bit wet, not sure.
https://youtu.be/9ftThV3MRBY
Does need tuning again, but this is pretty much where i put it, middle slightly sharp.


Which tuner app is that?

Gav Wood

  • Good talker
  • **
  • Offline Offline
  • Posts: 99
Re: Lockdown project - flat mounted MMM bc
« Reply #4 on: September 25, 2020, 10:01:05 PM »

Its called tuner, Bill farmer wrote it.

Found it when researching tuning on the discussions. Android only, you need to download something else to run it.

Senses all reeds at the same time, brilliant.
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Lockdown project - flat mounted MMM bc
« Reply #5 on: September 25, 2020, 10:08:35 PM »

I use tuner too.
Most of the time it works very well.

Really interesting project. Have you got any more photos?
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Lockdown project - flat mounted MMM bc
« Reply #6 on: September 25, 2020, 10:31:35 PM »


Its called tuner, Bill farmer wrote it.

Found it when researching tuning on the discussions. Android only, you need to download something else to run it.

Senses all reeds at the same time, brilliant.



Bill used to be a member here back a fair while ago, MIA since Aug 2017.
The latest Android APK can be found here
https://github.com/billthefarmer/tuner/releases/tag/v1.37
« Last Edit: September 25, 2020, 10:38:23 PM by Lester »
Logged

Gav Wood

  • Good talker
  • **
  • Offline Offline
  • Posts: 99
Re: Lockdown project - flat mounted MMM bc
« Reply #7 on: September 26, 2020, 04:56:47 AM »

Strap brackets made from pa register slide and bent aluminium from pa pallet rod, not sure i would do this again, aluminium is soft and will wear in time as shown by aluminium colour on plywood
Logged

Gav Wood

  • Good talker
  • **
  • Offline Offline
  • Posts: 99
Re: Lockdown project - flat mounted MMM bc
« Reply #8 on: September 26, 2020, 05:15:33 AM »

Buttons have had a notch taken out from each side to allow them not to foul the adjacent lever. Plan was to have enclosed keyboard but works as it is.
Maple arms are glued straight onto the brass bearings, which are mounted on a 3mm stainless steel rod. The rod slides to the left by about 5mm with pliers, then the whole mechanism pulls out.
Did cut some of the holes to square, but didnt make any difference to sound, was before i changed the pallet design.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Lockdown project - flat mounted MMM bc
« Reply #9 on: September 26, 2020, 05:14:31 PM »

"The frame And fondo is a magazine file from ikea, bass fondo a bit of hardboard from a picture backing at present. All the rest is scrap wood i had lying around."

Love it! Absolutely!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: Lockdown project - flat mounted MMM bc
« Reply #10 on: September 26, 2020, 05:50:36 PM »

This is a fascinating project, Gav. Having all the pallets in a row is brilliant - no tonal difference between the two rows. But do the outer row buttons go down farther than the inner ones, and does that take some getting used to?

I really admire the small size of the whole package. Though I reckon you might miss the pull high B on the inner row. The outer row push B is very handy in some passages, but awkward in others. Bravo.

Tiposx

  • Durham in England
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 259
Re: Lockdown project - flat mounted MMM bc
« Reply #11 on: September 26, 2020, 06:06:46 PM »

I love the size of the box and the sound - you were very brave to choose a three voice design.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Lockdown project - flat mounted MMM bc
« Reply #12 on: September 26, 2020, 06:16:29 PM »

I cannot help but wonder if there's any difference/advantage (other than having more space between treble and bass blocks) of having the third voice reeds mounted on a chimney rather than standing upright? This is prompted by the mention of them being "flat mounted" when really, mounting them on the chimney would likely have the same effects as if they were standing up.

Whatever, I think it's a smashing job, of which I am insanely jealous!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Gav Wood

  • Good talker
  • **
  • Offline Offline
  • Posts: 99
Re: Lockdown project - flat mounted MMM bc
« Reply #13 on: September 27, 2020, 04:33:26 PM »

Yes winston, i know what you mean about the standing up chimney block. When i looked at it Though i couldnt fit the block standing up, would have fouled on the bellows.
Sound is ok, and really loud, but nowhere near the quality of my busillachio.
The 3 reeds does make a difference over 2 in the box, and makes it much better. I also tried the reeds the other way round, prefer them this way for the sound.
Logged

Gav Wood

  • Good talker
  • **
  • Offline Offline
  • Posts: 99
Re: Lockdown project - flat mounted MMM bc
« Reply #14 on: September 27, 2020, 04:45:07 PM »

Stiamh, the buttons all go down an equal amount on both rows, makes a slight difference on the pallet but not enough to make it noticable to me, photo below.
Yes, getting used to the high b has been a problem, but if you only have one i am getting used to it. If i make another one, will probably go for a 19 button.
As you may have seen i am not that good a player, So it is all getting used to it.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal