Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Rusted-in bellow pins  (Read 7438 times)

0 Members and 1 Guest are viewing this topic.

Julie Atkin

  • New Starter
  • Offline Offline
  • Posts: 3
Rusted-in bellow pins
« on: October 04, 2009, 06:56:50 PM »

We have an old Hohner pokerwork style one row that has some dodgy reeds which we are hoping just need to be cleaned.  However, we cant get inside the box because the bellows pins are rusted into place.  Does anyone have any advice about how to remove these without damaging the box please?

Thank you

Julie
Logged

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Rusted-in bellow pins
« Reply #1 on: October 04, 2009, 08:37:58 PM »

You could try to get the head away from the box enough to either cut it off with a fine blade or pinch off with some pliers and then push the pin through with a nail punch. It can also help if you try wiggling the bellows around as you pull so that misaligned holes line up and allow less resistance to pulling.

Though I've not tried it with a melodeon before, certain other instances of rusted in pins have been solved by heating the end of the pin with a soldering iron - this heats the wood which expands making the hole larger. You can put a little moisture around the wood which can also help with the steam expanding the grain. Careful not to over do it and scorch the wood or mar the finish. 
« Last Edit: October 04, 2009, 08:54:19 PM by LJC »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Rusted-in bellow pins
« Reply #2 on: October 04, 2009, 08:42:18 PM »

My favourite method for loosening rusted items embedded in wood is a careful application of heat.  A standard electric soldering iron pressed onto the head of the pin for a minute or two will often release the pin.  After applying the heat try twisting the pin a little before pulling. 

I fear that if the pins are so badly rusted the reeds may need more than cleaning.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Rusted-in bellow pins
« Reply #3 on: October 04, 2009, 08:54:59 PM »

Sorry cross post with Theo there. Just as he said.
Logged

Julie Atkin

  • New Starter
  • Offline Offline
  • Posts: 3
Re: Rusted-in bellow pins
« Reply #4 on: October 04, 2009, 10:23:00 PM »

Thanks everyone - we'll go hunting for our soldering iron. 

N
Logged

Julie Atkin

  • New Starter
  • Offline Offline
  • Posts: 3
Re: Rusted-in bellow pins
« Reply #5 on: October 04, 2009, 10:25:05 PM »

Sorry, my reply flew off too soon.

Second question - does anyone know, please, how we can clean off any rust we find on the reeds?

Thank you again

Julie
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Rusted-in bellow pins
« Reply #6 on: October 05, 2009, 12:20:20 AM »

Hi Julie,

Nice to see you've made it over to melnet! Hope Gavin's ankle is mending nicely.

Second question - does anyone know, please, how we can clean off any rust we find on the reeds?
Answer: Very carefully! Theo or Rees may well reply more fully, but my recommendation would be to use a glass-fibre pen, like this one.....
http://www.artifolk.co.uk/catalog/products/airbrush_accessories/faber_castell_glass_fibre_eraser_pen.htm

It should remove the rust without removing too much steel, but I concur with Theo's comment about badly rusted bellows pins signifying further trouble inside. If there is very bad rusting on the reeds, it may have caused such deep pitting that the reeds may not be salvageable. If you succeed in getting the rust removed and the reeds still are in reasonably good condition you will still need to re-valve and re-wax the reeds before retuning them.

Good luck! Let us know how it goes.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Rusted-in bellow pins
« Reply #7 on: October 05, 2009, 05:47:16 AM »

When my BMW bike's brake pins wouldn't move  ??? the garage man said that 'a little gentle heat'  ;) would often shift them  Five minutes with his oxyacetylene torch  :o later - out they popped :Ph
Logged
  _       _    _      _ 

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Rusted-in bellow pins
« Reply #8 on: October 05, 2009, 07:39:42 AM »

Oxyacetylene burns a little too hot for use on melodeons... or maybe at the right temperature, some might say.

Regarding rusty reeds, you will need to take the plate off of the reed block to clean the under side. As Steve says - you will need to re-valve and wax again. Clean all of the remaining wax off the reed block once you have taken the reed plates off. Wax can be cleaned with turps or white spirit and then the block sanded.

Old valves can just be pulled off and the plates cleaned to get the wax off the edges and any sticky residue off from where the valve was attached.

Maplin sell the fiber sanding pens here http://www.maplin.co.uk/module.aspx?moduleno=3932. An old toothbrush can also be very useful for cleaning the reeds. Once you have got them looking more respectable you can use a piece of greaseproof paper slid under the reed tongue to clean any particles which might have got trapped in the gap (do this before re-valving as it would be a pain to try getting iron oxide dust out from the air gap and valve.

Try to avoid getting your fingers on the reed tongues as they can cause future corrosion by depositing acidic sweat on the metal. Any you do touch you can just wipe down with white spirit to remove before finishing up and waxing in.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Rusted-in bellow pins
« Reply #9 on: October 05, 2009, 08:20:38 AM »

And then having done that they will probably be seriously out of tune!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

gmatkin

  • Gavin Atkin
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 719
    • Julieandhersqueeze.com
Re: Rusted-in bellow pins
« Reply #10 on: October 18, 2009, 02:54:37 PM »

Thankfully, the reeds didn't turn out to be too bad! Phew...

Gav

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Rusted-in bellow pins
« Reply #11 on: October 19, 2009, 08:17:09 PM »

Gav and Julie popped over to see us on Saturday afternoon and the box is in pretty good condition. All the valves are plastic other than the large basses which are leather with a plastic 'spring'. Two of the pull notes high up the keyboard only had one reed sounding but a bit of poking around soon got the other reeds going. One of the second octave notes (b) sounded dreadful and the tremolo reed kept flicking the strobe tuner over to 'c' it was so sharp.

The only criticism I have about the Peterson Strobo-Flip is that it gets confused if notes are wildly out of tune and I had to resort to using a reference note on the concertina to bring it down within range. The reeds are a bit rusty but not alarmingly so and the box would be better for a thorough end to end tuning but it's playable as is and I'm sure Julie will have lots of fun with it.  ;D
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

gmatkin

  • Gavin Atkin
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 719
    • Julieandhersqueeze.com
Re: Rusted-in bellow pins
« Reply #12 on: October 20, 2009, 02:16:01 PM »

I've thanked Peter elsewhere on this forum for patching up our little 1140, but just in case he hasn't been to those particular places, I'd like to record our gratitude here also. As well as getting the little box back on the road, he taught me some useful knowledge about the inner workings of these things that I didn't have a clue about...

I'm not sure I'll be investing on one of those strobe tuners though! (As a fiddler, what I'd like is an analogue scale and two lights tuner with a hypercardoid mic at an affordable price - but I guess I should keep things like that for another forum...)

And now we're waiting for our new 1140D to arrive... I wonder what that will be like, and where it's scale will be? One of the nice things about the 1140 G is that it's nicely low, but I guess it's likely that the 1140D will be in the same range as the D row of a Hohner DG.

Gav

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Rusted-in bellow pins
« Reply #13 on: October 20, 2009, 03:08:16 PM »

.... but I guess it's likely that the 1140D will be in the same range as the D row of a Hohner DG.
Yes that's right, Gav. But don't forget that you have the low octave voice as well, which is an octave lower than the D-row of a normal 2-row Hohner. So you have a good growly sound. Lester is playing one here:
http://www.youtube.com/watch?v=7R9HxIWkAHY
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Rusted-in bellow pins
« Reply #14 on: October 20, 2009, 03:35:57 PM »

Steve old bean, thou art confoosed.
Lester is playing a 114 but Gav and Julie's is a two voice 1140.  ::)
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Rusted-in bellow pins
« Reply #15 on: October 20, 2009, 05:21:39 PM »

Steve old bean, thou art confoosed.
Lester is playing a 114 but Gav and Julie's is a two voice 1140.  ::)
Whoops! So I am. Apologies all round.
What a little piece of nothing a 0 is, but what far-reaching effects it has.
I'll get my coat and go for a long stand now.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

gmatkin

  • Gavin Atkin
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 719
    • Julieandhersqueeze.com
Re: Rusted-in bellow pins
« Reply #16 on: October 21, 2009, 01:13:11 PM »

No, don't punish yourself too much - I don't think you've been bad exactly.

I think it's a common enough misundertanding, thanks to Hohner's model numbering system.

Gav

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Rusted-in bellow pins
« Reply #17 on: October 21, 2009, 04:38:46 PM »

I've thanked Peter elsewhere on this forum for patching up our little 1140, but just in case he hasn't been to those particular places, I'd like to record our gratitude here also. As well as getting the little box back on the road, he taught me some useful knowledge about the inner workings of these things that I didn't have a clue about...

Thanks are not needed Gav, it was a pleasure. I haven't been able to be online much since the weekend as we have broadband problems at the moment and we are currently battling it out with BT...  >:(

I'll try and catch up with things once the service has been restored.

Pete.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

gmatkin

  • Gavin Atkin
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 719
    • Julieandhersqueeze.com
Re: Rusted-in bellow pins
« Reply #18 on: October 21, 2009, 06:00:42 PM »

Hi Pete -

Don't forget to take a peek at the wonderful Bobby Gardiner on YouTube. Try this for example: http://www.youtube.com/watch?v=MrHOVnFLOV4

I want to hear some more of this fabulous stuff.

And also check out the proposed list of session tunes for Frittenden: http://frittendenfestival.com/sessions/ They might turn out to be ong standing favourites!

Gav

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Rusted-in bellow pins
« Reply #19 on: October 22, 2009, 09:31:52 AM »

Greetings Gavin, long time no see!

I'd mentally put this little thread down as a quickie, but it seems to have a life of its own.  Theo - could I please nominate this fine pin/motor bike/Strobo-Flip/welding torch/session tunes for Frittenden chimira for as another contender for the "thread-drift-of-the-year" award  >:E  Chris

PS: Come to think of it that BMW might have been a 1140D -  would this disqualify the thread?
Logged
  _       _    _      _ 
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal