Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner Corona III Bass Side Fondo Felt  (Read 1057 times)

0 Members and 1 Guest are viewing this topic.

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Hohner Corona III Bass Side Fondo Felt
« on: October 09, 2020, 07:59:59 PM »

Where do you guys purchase this?

« Last Edit: October 10, 2020, 04:05:54 PM by Vallenato831 »
Logged
Corona III x8

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Corona III Bass Side Fondo Felt
« Reply #1 on: October 09, 2020, 08:17:08 PM »

Do you mean the gasket material under the reed blocks?  If so there are two materials.  Either self adhesive olovisc which is familiar to people who have been on Emmanuel’s courses.  There is also a non self adhesive material also confusingly called Olovisc,  which is the material used by most Italian makers as gaskets under reed blocks.  Both materials available from Carini.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Re: Hohner Corona III Bass Side Fondo Felt
« Reply #2 on: October 09, 2020, 08:23:29 PM »

The colored gasket material that is normally glued onto the case. 

For example, the mint green material on the attached photo.   
Logged
Corona III x8

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Corona III Bass Side Fondo Felt
« Reply #3 on: October 09, 2020, 10:00:18 PM »

I don’t know any source for that material,  but the ones I mentioned do the same job.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Conjunto Dave

  • Member
  • *
  • Offline Offline
  • Posts: 28
Re: Hohner Corona III Bass Side Fondo Felt
« Reply #4 on: October 09, 2020, 11:30:40 PM »

I would contact the Hohner C-shop. They still manufacture the Corona III (in China), and the dimensions shouldn't have changed. They must have a supply of this material already cut to size.

http://www.hohner-cshop.de/en/contact/

Logged

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Re: Hohner Corona III Bass Side Fondo Felt
« Reply #5 on: October 10, 2020, 12:04:02 AM »

I ended up going to Michaels, local arts and craft stores.  They sell similar self adhesive felt material.  Not exactly the same, but very similar.  Such a PITA to cut out the little holes though.
Logged
Corona III x8

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Re: Hohner Corona III Bass Side Fondo Felt
« Reply #6 on: October 10, 2020, 12:14:56 AM »

For the sake of anyone who searches here looking for the same thing, I think CGM does actually have it, as well.  (Olovisc, in this case.)

http://www.cgmmusical.co.uk/CGM_Musical_Services/Felt_Leather_Pallets.html#15

There's also self-adhesive thin cork material at many craft stores, but I'm guessing it runs the risk of leaking through channels of fine cracks.
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Hohner Corona III Bass Side Fondo Felt
« Reply #7 on: October 10, 2020, 12:19:49 AM »

I ended up going to Michaels, local arts and craft stores.  They sell similar self adhesive felt material.  Not exactly the same, but very similar.  Such a PITA to cut out the little holes though.

Are there any tools available to make this job easier?
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner Corona III Bass Side Fondo Felt
« Reply #8 on: October 10, 2020, 12:36:48 AM »

I use a hole punch.

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Re: Hohner Corona III Bass Side Fondo Felt
« Reply #9 on: October 10, 2020, 04:46:37 AM »

For the sake of anyone who searches here looking for the same thing, I think CGM does actually have it, as well.  (Olovisc, in this case.)

http://www.cgmmusical.co.uk/CGM_Musical_Services/Felt_Leather_Pallets.html#15

There's also self-adhesive thin cork material at many craft stores, but I'm guessing it runs the risk of leaking through channels of fine cracks.

I thought it was for the pallets.  Must be the same for the fondo?   
Logged
Corona III x8

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Re: Hohner Corona III Bass Side Fondo Felt
« Reply #10 on: October 10, 2020, 04:50:07 AM »

I ended up going to Michaels, local arts and craft stores.  They sell similar self adhesive felt material.  Not exactly the same, but very similar.  Such a PITA to cut out the little holes though.

Are there any tools available to make this job easier?

I used an exacto knife and scissors.  See attached photo, I cleaned it up a bit more, but sure was tedious.  My first go was laying it on the fondo, but that proved way too difficult for cutting.   Attaching to the reed block was much easier. 
Logged
Corona III x8

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner Corona III Bass Side Fondo Felt
« Reply #11 on: October 10, 2020, 07:38:08 AM »


I thought it [olovisc] was for the pallets.  Must be the same for the fondo?

Olovisc is too thin and not resilient enough to use as pallet facing material. It would probably work, but almost certainly would be very noisy on the return action. It would be fine for a fondo gasket and as a gasket around the edges of the reed block chambers for screwed or nailed reed plates.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner Corona III Bass Side Fondo Felt
« Reply #12 on: October 10, 2020, 07:46:43 AM »

Are there any tools available to make this job easier?

I use a hole punch.

I have a set like this:
https://www.amazon.co.uk/toolzone-PN104-Leather-Gaskets-Plastic/dp/B001MG3ETU/ref=sr_1_12

As they come, they're good for leather, but for weaker material such as felt and cork, I sharpened the punch by carefully filing the outside chamfer so that the central hole was surrounded by a sharp rim of steel.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner Corona III Bass Side Fondo Felt
« Reply #13 on: October 10, 2020, 09:56:50 AM »

Yes, similar to that. I draw a cross over the hole centre because the punch is difficult to get in the right spot, and then sight on where the cross shows around the punch.

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Hohner Corona III Bass Side Fondo Felt
« Reply #14 on: October 10, 2020, 12:30:34 PM »

Are there any tools available to make this job easier?

I use a hole punch.

I have a set like this:
https://www.amazon.co.uk/toolzone-PN104-Leather-Gaskets-Plastic/dp/B001MG3ETU/ref=sr_1_12

As they come, they're good for leather, but for weaker material such as felt and cork, I sharpened the punch by carefully filing the outside chamfer so that the central hole was surrounded by a sharp rim of steel.

They look very similar to the tools we used for making vinyl and neoprene disks for valve inserts. I  knew them as Swedish ring punches. They were called by another name, sometimes...Mabyn punches, or something of that ilk. The nearest tools I can find to tools of that name now are Mubea punches, but they seem to be pretty standard sheet metal punches.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal