Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Changing bellows tape on end frames  (Read 1603 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Changing bellows tape on end frames
« on: October 12, 2020, 05:07:15 PM »

I’ve retaped several bellows, but I’ve never had to replace the tape at the very ends of the bellows that are glued up against the end-frames. I have to do this now, and I don’t wish to unglue the bellows from the frames. Any recommendations? Getting the old tape out has been extremely difficult..
Logged
C#/D player

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: Changing bellows tape on end frames
« Reply #1 on: October 12, 2020, 05:15:59 PM »

take off the frames- no big deal  (:) I do it every time.
Logged

Kon

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 165
Re: Changing bellows tape on end frames
« Reply #2 on: October 12, 2020, 05:19:29 PM »

I have done this recently, and found running the tip of a very sharp, thin knife blade between the bellows and the frame helped get the tape out. I was very careful to control the depth of the blade so that I didn't fully separate the bellows from the frame. I then attached the new tape, and ran a bead of PVA between the frame and the bellows fold to ensure they were fully and securely reattached. I suppose this amounts to *partially* ungluing and then regluing the bellows.

Disclaimer: I made this up as I was going along, under my own steam. I am in no way shape or form a professional or even experienced fettler. This may not be a good idea. But it worked well for me, and made what I expected to be a horrible job a lot easier than I thought it would be.
Logged
GC Erica

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Changing bellows tape on end frames
« Reply #3 on: October 12, 2020, 05:41:17 PM »

I'm sure the knife/scalpel method is also employed by Lester . If you look for his series of fettling videos, you will see him do so.

Sir John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

MikeK

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 354
Re: Changing bellows tape on end frames
« Reply #4 on: October 12, 2020, 06:51:39 PM »


 I use a butter knife to ease the frame from the bellows. After fixing the tape, I always put a generous amount of pvc
 in between to make sure there is no air leaks and then clean any residue with a damp cloth.
Logged
I always respect my elders but they are getting fewer in numbers.

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Changing bellows tape on end frames
« Reply #5 on: October 12, 2020, 09:41:51 PM »


 I use a butter knife to ease the frame from the bellows.
I prefer to use a rather blunt knife also which you can twist now and again rather like opening a clam.If you accidentally go all the way through to the inside remember to glue the inside seam as well to ensure its airtight.    Good luck, John

P S. All these jobs become  easier with practice - keep a damp cloth/wet-wipe handy for the excess glue - doing the ends is always messier!
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Changing bellows tape on end frames
« Reply #6 on: October 13, 2020, 07:22:03 PM »

I find curved end tweezers useful to pick out old tape remnants and scrape the 'canyon' clean.  And using narrower replacement tape strips may make it easier for the next repairperson...
Logged

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Changing bellows tape on end frames
« Reply #7 on: October 13, 2020, 09:33:43 PM »

I have a 12" ruler alloy ruler.....the sort with the beveled faces on two edges.  I found the wedge shape eased the bellows away sufficiently along the hole length of the sides / top & bottom in one go to be able to remove the original tape's bond to the frame.  Flat of the ruler to the wood, bevel to the tape.   I have an offset cake slice  :-[ which I have used on guitar/Mandolin backs which has a broad, thin, but blunt sided blade which eases the tape off and will carry some heat and moisture to the glue if needs be.   The ruler is useful for pushing the tape down into the valley in one go on re-taping.
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 246
Re: Changing bellows tape on end frames
« Reply #8 on: October 14, 2020, 02:06:17 PM »

I did this very job yesterday. Started with the "dig it out" approach but the old bellows tape was extremely well glued down. It kind of worked but took ages. I also found the bellows partially coming away from frames in the process so decided in the end to take frames and bellows apart. Even then, getting the old bellows tape off was really hard work. Digging out the old tape obviously can work but i just felt happier separating bellows and frames. Sounds really though like either method has been used sucessfully and maybe it depends on the make, model and year of melodeon and whether anyone has done any regluing. Mine is a 50's/60/s Hohner that didnt show any signs of fresh glue. Incidentally removing bellows tape was "interesting" in so far as it came off very easily all in one piece on the short sides of the bellows. No mess, just peeled off super easy. Yet on the long sides although the same happened close to the corners most of the tape was very very hard to remove. Im sure there's a scientific reason but i cant figure it out!
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal