Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Converting the key of an entire row  (Read 1115 times)

0 Members and 1 Guest are viewing this topic.

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Converting the key of an entire row
« on: October 22, 2020, 04:47:23 PM »

It seems to be not uncommon practice to convert entire rows to another key, by clever transpositions and flippings of reeds from other blocks, weighted PA reeds, and so on.  I would greatly appreciate some tips, and also am wondering what kinds of pitfalls to watch out for.  Here are some of my (possibly incorrect) assumptions, of which I would greatly appreciate some verification or correction from the experienced folks here.

  • In my understanding, the tone of the reed is preserved when a drop of solder is added, but you run a greater risk of changing the timbre if you're filing the reed.  The amount of metal removal necessary for a semitone shift (up or down) seems out of the question to me, unless we're talking about filing a weight that's already on the tip of a low reed.
     
  • Therefore, it seems safest to use tiny drops of solder, and file those down, to drop a note a semitone or more.  This leaves the belly of the reed alone and better preserves the tonal character.
     
  • The easiest reedblocks to use in this way to perform entire conversions on without additional reeds from other rows would seem to be ones that are a major third above, e.g. F to C#, because 90% of it can be achieved by adding drops of solder.  This leaves me with one glaring question, however:
e.g. to obtain a C# outer row from F inner row:
  F3/A#3  (fabricate from PA reed)
  G#3/C4  (drop & flip C4/E4)
  C#4/D#4 (drop E4/F4)
  F4/F#4  (drop F4/G4)
  G#4/A#4 (drop A4/Bb4)
  C#5/C5  (drop & flip C5/D5)
  F5/D#5  (drop F5/E5)
  G#5/F#5 (drop A5/G5)
* C#6/A#5 (raise C6/Bb5)? Or is it preferable to fabricate from a PA reed?
  F6/C6   (drop F6/D6)
  G#6/D#6 (drop A6/E6)


Am I proceeding from some incorrect assumptions, or am I close to the mark here?  Thank you for your help!
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Converting the key of an entire row
« Reply #1 on: October 22, 2020, 05:32:58 PM »

I've done quite a bit of this sort of thing and yes, you are on the right lines.  Your ideas about the preference for adding solder is true up to a point, but bot always true.
First my understanding of reed design.   
In ideal circumstances there is an ideal length for a reed tongue for a given pitch.   For low pitches this becomes increasing impractical because the ideal length for reed performance starts to get too large to easily fit in a portable instrument.   The compromise which can be seen in any accordion or melodeon is to make the reed shorter and add weight to the tip.  At the other end of the scale the ideal length of a high pitch tongue is inconveniently short. So here you can see a few design changes to allow a longer reed.  Often high pitch reeds are more tapered in width, and always the profile is thick at the base and tapers in thickness towards the tip.  You can see this thickening at the base very clearly if you look at older reeds where the two tongues are both the same length, even when there is a difference in pitch.   For example the top reed on an 11 button C row is G/D  and the G is 5 semitones above the D.  So in this example you have a lot of scope for lowering the pitch of the G by re-profiling the reed.  You can usually also lower the D by careful filing too, though probably only by 1 or perhaps 2 semitones.



Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Re: Converting the key of an entire row
« Reply #2 on: October 22, 2020, 05:57:25 PM »

Theo, thanks, that's helpful.  But how would you go about making that C#6/A#5 reed for the C# row?  In my experience with PA reeds in that octave, you really want to avoid re-profiling toward the tip, as it's just a hair's breadth away from becoming too thin.

Edit: Maybe you already answered this and I misunderstood.  Are you suggesting using the 11th button from a C row (G6/D6) to make the C#6/A#5?  I suppose if I am already sacrificing an F row, I am likely to have a C row handy.  This would at least enable me to save the rest of the C row as the inner row of a G/C or B/C, or as a 4th button start row.
« Last Edit: October 22, 2020, 06:25:43 PM by Gonk »
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Converting the key of an entire row
« Reply #3 on: October 22, 2020, 06:37:53 PM »

I wasn’t suggesting any specific conversion,  just sharing  an additional tool.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Re: Converting the key of an entire row
« Reply #4 on: October 22, 2020, 06:58:58 PM »

I wasn’t suggesting any specific conversion,  just sharing  an additional tool.

Understood, thanks.  How would you personally go about it?
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Converting the key of an entire row
« Reply #5 on: October 22, 2020, 07:05:31 PM »

If possible I would avoid using a PA reed.  I’ll have to go and look at a layout chart to give you a proper answer
« Last Edit: October 22, 2020, 07:11:44 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Converting the key of an entire row
« Reply #6 on: October 22, 2020, 07:14:52 PM »

If I was creating a C# row I would just take the whole row from a CC# box.  There are a few of those around that are unlocked and unwanted.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Converting the key of an entire row
« Reply #7 on: October 22, 2020, 07:23:19 PM »

What is the box you are starting with and what do you want to end up with?  I always treat the complete instrument conversion at once rather than doing each row separately.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Converting the key of an entire row
« Reply #8 on: October 22, 2020, 07:32:17 PM »

I find it helpful to give numbers to every reed pair. I start at C3 at 1 and just go up from there. C#3 is 2, D3 is 3 etc....
I go up each row then combine them to make a complete list of every available pair.
Alongside I make a required list and compare the two.
It stops me from making rash assumptions, and makes selecting the smallest changes easier for me.
I've shown my chart and one of my first attempts at using it. I have later ones, but they have too many scrawls on to make sense to normal people. I find that I can normally limit retuning to two semitones at the most, and more usually just one semitone.
I have no doubt Theo and the experienced fettlers don't need this stage, but it helps me.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Re: Converting the key of an entire row
« Reply #9 on: October 22, 2020, 07:48:39 PM »

Nice, Pete.  I've been toying with the idea of writing a small computer program to do the heavy lifting.  That would certainly require thinking of the notes in terms of number positions as well.  Right now I just have a large text document with reeds listed in the terms I've been using... [note][octave].

Theo, to answer your question, I want to nail down a reliable method for making a row when needed.  Mostly, I would like to be able to convert some of the G/C and A/D boxes that are commonly available the in the US and have the nice old Hohner reeds, to B/C and C#/D respectively, both for my use and for others like me who like that tone but find them hard to find in the US.  So I'd like a method that doesn't sacrifice the tone of the nice reeds.  Which - I know some will argue, and from one point of view I agree - it is a shame to change at all.  Many of you UK folks seem to have a "method" down, but perhaps the method is often, as you suggest, having more old Hohners floating around in your vicinity, including C/C# and B/E.  Those tunings are rare in the US, though some C/C# did appear on eBay last month, sold from Australia, and not at "unloved" prices.
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: Converting the key of an entire row
« Reply #10 on: October 22, 2020, 08:57:56 PM »

Mostly, I would like to be able to convert some of the G/C and A/D boxes that are commonly available the in the US and have the nice old Hohner reeds, to B/C and C#/D respectively, both for my use and for others like me who like that tone but find them hard to find in the US.  So I'd like a method that doesn't sacrifice the tone of the nice reeds.

I mused about this in an earlier thread, with input from Mike Rowbotham. Have not got around to doing it though!

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Re: Converting the key of an entire row
« Reply #11 on: October 22, 2020, 10:23:04 PM »

Thanks, Stiamh.  I'm surprised by the general agreement in that thread with the idea of tuning reeds up by full semitones...I would feel very nervous doing that on a nice reed.  I think I'm competent with a file, but that is a lot of metal, and especially on high notes, runs the risk of leaving the tip so thin that it starts to flop and actually drop drastically in pitch (and often break).  But in the case of, say, the G/C to B/C Paolo conversion, it makes sense... it's your only option, if you're determined to use the original reeds.  And the fact that Mr. Rowbotham condones it means that it must have merit.  I guess my method would be to re-profile the reed most of the way, then use a scratcher.  And I'd certainly practice on some PA reeds first.  I'd love more input on this...
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal