Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Slide/Register advice.  (Read 1660 times)

0 Members and 1 Guest are viewing this topic.

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Slide/Register advice.
« on: October 31, 2020, 12:07:49 PM »

I would like some advice on introducing slides/registers to this Box from those who have practical experience.

It is 3 voice, LMM.....with blocks that are laid out as LM / MM / ML.  I would like to at least, be able to take out the 'outer row' L reeds and, were it feasible, possibly the 'MM's on the middle block, to give me LM and MM options.

I have experimented with a temporary insert/s and have attained the effect that I want to achieve tonally.

I have 1.5mm aircraft ply to hand.  I could/would work with acetate sheet or metal as required, but wood is arguably easier to handle for me.
 
My concerns/questions are practical - principally around using ( or not!) long "slots" for the 'M' reed side ? of the L'M blocks, as opposed to individual holes per reed and the effect a 1.5mm thick slide will have, if slotted, regarding adjacent reed/s & holes and air moving around where it shouldn't and pressure being affected.

That concern links in to another around whether, if long slots are not practical, as I fear they are not, whether to have a full width slide with paired holes, or whether to 'rout' the block over just half it's width and put a half width slide in, to impact on just the 'L' reeds.

For activating I am looking to put a long sided 'D' shaped route into the block at the button end, and use (probably) CGM buttons, connected to the slide by a flat sided dowel of appropriate diameter.


I would welcome input from those who have added slides.  I am sure I saw a post from Lester somewhere with an image of a slotted slide....but that was possibly for thirds.  In that case air to adjacent reeds may not have been an issue, so may not help with this project.

If it needs to be a 'hole for hole' design, so be it.

On a similar tack, I might have liked to consider a slide for the 1/3'ds on the bass side......but......instinct tells me that is going to be impractical because of the design as per the images.  ie. multi chamber air inlet to x6 reeds per button via a slotted button.

https://1drv.ms/u/s!AjqrfvOr1YWpgQIxwpa1sNtOH9HZ?e=7iuXDp

I have access to appropriate wood working equipment for the task.

Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Online Online
  • Posts: 1327
  • Re-hohn a Hohner
Re: Slide/Register advice.
« Reply #1 on: October 31, 2020, 12:58:34 PM »

Your mockup piece would allow air from every open pallet to reach every reed.
Routing is the way to go, or build up the thickness on the non-slide side with the same aircraft ply.
One important factor is the space between the round air holes. You need at least as.much blank space as hole space, or you'll end up with holes in the slide that aren't round so they provide a proper seal.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Slide/Register advice.
« Reply #2 on: October 31, 2020, 02:06:47 PM »

Your mockup piece would allow air from every open pallet to reach every reed.
I thought it would.  As "trapped" paper+tape, it doesn't....but once there is a 1.5mm gap, I assumed there would be too much flow.  It will have to be individual holes for the L reeds, and short double hole slots for the M's then, rather than a long slot for all the 'M' row reeds? 
Routing is the way to go, or build up the thickness on the non-slide side with the same aircraft ply.
Hmm, as below.
One important factor is the space between the round air holes. You need at least as.much blank space as hole space, or you'll end up with holes in the slide that aren't round so they provide a proper seal.
That may be the straw that breaks the camels back.  The block design makes it 'tight' to create the hit/miss ( for the holes ) without restricting the air marginally.  Rather than double the problem, by going full width and have to "manage" the M reeds, which will always be speaking anyway on the LM blocks, a narrow / half width slide for just the L reeds may be the best option....either via a rout, or, thinking aloud, initially via a build up of ply, for a more formal mock up, to test the theory before letting loose with power tools. Any routing can be addressed later if all else is equal.

Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Online Online
  • Posts: 1327
  • Re-hohn a Hohner
Re: Slide/Register advice.
« Reply #3 on: October 31, 2020, 02:27:10 PM »

http://forum.melodeon.net/index.php/topic,25468.msg304072.html#msg304072

Link to my solution to a slide stop, in this case it's thirds stop but it does show how I had to cut slightly oval holes to maintain the air seal.
You can see the channel for the slide made from the same ply.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Slide/Register advice.
« Reply #4 on: October 31, 2020, 03:23:25 PM »

Thanks for that.....
Logged

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Slide/Register advice.
« Reply #5 on: October 31, 2020, 04:50:42 PM »

What did you find was the best way to create the holes in the 1.5mm material, Pete ? Forstner bit's ? router bit or some other form of drill?  I have done some work with 3mm ply and found it inclined to tear around the edges at the required diameter......your cuts are very clean.
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Online Online
  • Posts: 1327
  • Re-hohn a Hohner
Re: Slide/Register advice.
« Reply #6 on: October 31, 2020, 05:16:27 PM »

I used a piercing saw.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Slide/Register advice.
« Reply #7 on: October 31, 2020, 07:26:20 PM »

Ok.....I have a lot more holes to make, so I may try and find an alternative.  I might give a 'step drill' a go.  They are supposed to be more gentle and less aggressive. 
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Online Online
  • Posts: 1327
  • Re-hohn a Hohner
Re: Slide/Register advice.
« Reply #8 on: October 31, 2020, 08:18:37 PM »

Very careful routing with a sharp cutter and a precise jig could be the way to go if you don't want to use a saw.
You could probably get a saw and blades from Mr eBay for £10-15 and you'd be set up for cutting out concertina ends too.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Microbot

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 345
Re: Slide/Register advice.
« Reply #9 on: October 31, 2020, 08:25:31 PM »

Hi Nigel,

Place the section of plywood onto a thick, clean wood surface... Use a standard wood drill bit, with a nice long centre locating spike...

Drill far enough in, to go right through with the spike, but only far enough to cut into the top layer of plywood with the edge of the bit....

.... Then Flip the piece of plywood over and drill from the other side, locating into the centre spike hole.

The disc spins out and the hole is clean....

Works for me!

I've done tens, maybe hundreds of sliders like this... (I make a rubbing, stuck to the plywood, so the pattern is 100% faithful to each reedblock I'm working on)

Mike R
Logged

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Slide/Register advice.
« Reply #10 on: October 31, 2020, 09:27:48 PM »

Cheers both.....I am of the Brass Rubbing generation Microbot and that is how I have made 'patterns' for felt gaskets for the blocks on older P/works previously, so will do.
Logged

Microbot

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 345
Re: Slide/Register advice.
« Reply #11 on: October 31, 2020, 09:45:58 PM »

I am of the Brass Rubbing generation Microbot and that is how I have made 'patterns' for felt gaskets for the blocks on older P/works previously, so will do.

Yep....good for gaskets too.... It’s great when someone knows what you’re talking about!

Cheers

Mike
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Online Online
  • Posts: 1327
  • Re-hohn a Hohner
Re: Slide/Register advice.
« Reply #12 on: October 31, 2020, 10:59:03 PM »

My only reason for not using a drill bit was that the solid sections between the round holes look to be too small to "park" the slide without a little air seeping past.
My sawn holes are very slightly oval so there is more coverage.
I was concerned that smaller diameter holes in the slide would shut off the air effectively but might have some effect in restricting the airflow when open, hence the irregular shape.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Microbot

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 345
Re: Slide/Register advice.
« Reply #13 on: November 01, 2020, 12:05:09 AM »

Yep, but I find it's easy to ream out a round hole to be oval...

Mike
Logged

Dave Praties

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 195
Re: Slide/Register advice.
« Reply #14 on: November 01, 2020, 07:40:00 AM »

What did you find was the best way to create the holes in the 1.5mm material, Pete ? Forstner bit's ? router bit or some other form of drill?  I have done some work with 3mm ply and found it inclined to tear around the edges at the required diameter......your cuts are very clean.
Nigel- if you are struggling with slide making, or not happy with the results, you could send me a drawing/rubbing with as much info as poss, and I can laser cut you your slides. I have a lot of 1.5mm ply, and free use of a laser cutter where I work, so it wouldn’t cost you anything. It’s often more satisfying to reach a goal using a craft alternative, but sometimes when we run short of time or patience, technology can jump in with good results!
Dave.
Logged
Castagnari Handry 18 G/C. Castagnari Handry 18 D/G.    Self-built G/C 2.5/12 bass. almost finished after 7 years! Bb/Eb Preciosa. C/F Lilliput.

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Slide/Register advice.
« Reply #15 on: December 04, 2020, 10:47:02 PM »

My final fettling job for the foreseeable future is taking on the 'L' reed, treble end stop and I need some insight/guidance on the logic and performance issues I am facing.

To reiterate, the x3 blocks are set up as LM 11/11 holes / MM 11/12 holes / ML 12/12 holes, so my 'L' reeds are on the outside of the two outer blocks.

As things stand, as alluded to by Pete, I can not utilise the existing circular air holes for the project as they do not allow adequate material to effect a 'hit'/miss for the slide.  I have made slides in 1.5mm ply to establish this and it just isn't viable.

As a 'first shot' solution, I have created a new 'face' for the blocks using very thin (0.25mm) Plasticard to convert the round holes to square.  Its a loose fit option at the moment, but very effective.  I have then created a slide out of  a heavier/appropriate gauge,  Plasticard, also with square holes which allows the hit an miss function on the 'L' reeds and the twin aperture for the 'M's.

In a dry run, it works well.....

But......in order to work with the LM/MM/ML set up I am going to have to remove wood from all three blocks and then create a dual 'pull' system to operate on both slides, beneath the outer blocks simultaneously and equally. 

Thinking out loud - and being prepared to be told "because" - I am wondering, despite all that I have already done, whether it would not be more practical to make the blocks MM/LL/MM and just do the hit/miss on the middle block, with a single slide, operated on a direct 'pull' push button/lever. 

I might need to do a little extending/packing reducing of the reed blocks but it would undoubtedly be a much simpler option unless there is some qualitative reason - tone wise - why it would be a bad idea ?
Logged

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Slide/Register advice.
« Reply #16 on: December 15, 2020, 11:32:36 AM »

I have completed the 'slide' for the L reeds on the Socin.  In the end I routed the blocks 1.8mm deep, then fitted a .25mm shim of plasticard which was punched to reduce the air holes marginally.   This allowed for a 1.5mm "U" shaped slide to accommodate both rows with a single blade with a 'tab'.  A block of styrene super-glued to it and drilled and dowelled provides the anchor for the threaded shaft.
 
My initial posting was wrong in that the blocks were set up as ML/MM/LM, which made the job a bit easier as the "legs" are closer.  I could not move the 'L' reeds to the middle block as I hoped, to make life really easy, as the blocks were too small.

The external fitting is a CGM chrome 'pull' button, inside the work is invisible. 

On the bass/chord end, two of the chords have x3, paired reed plates in 2 octaves, the other two have x2, paired 1st's, one 3rd and one 5th plate.  I have removed the 1/3's, by re-jigging the set up to have a second '5th' plate in those two sets, an octave apart, without 3rds, and taped off on the triple sets.

 


 

Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal