Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3 4   Go Down

Author Topic: Tool Kit for melodeons  (Read 6115 times)

0 Members and 1 Guest are viewing this topic.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tool Kit for melodeons
« Reply #20 on: November 14, 2020, 07:12:27 AM »

Screwdrivers:

...For instance, I worked as a TV engineer for about eight years. They were notorious for being full of screws in hard to locate positions. While some fixings  were steel and all you had to was magnetise the screwdriver, others were non-ferrous...

Many screws used in melodeons are ferrous. I have a set of magnet-tipped screwdrivers which work a treat. Like these.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tool Kit for melodeons
« Reply #21 on: November 14, 2020, 07:21:46 AM »

Soldering iron, variable temperature:

I have one similar to this. I have ground down one of the replacement tips down to a fine point which can get between reed plates even just 1 mm apart.

Used for melting and remelting reed wax in stick form. The variable temperature control is essential, otherwise the iron can get too hot and burns the wax.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tool Kit for melodeons
« Reply #22 on: November 14, 2020, 07:38:32 AM »

Masking tape, low-tack:

Like this.

Absolutely indispensible. I reduce the tackiness even further by pressing the sticky side to a piece of fabric, e.g. T-shirt, jeans, etc. before applying it. I use it all the time for:

1. A temporary label across the top of reed blocks so you can write on the notes of the reeds, or other identification marking. Saves having to mark the actual wood of the reed block, which I hate to see.

2. Blocking off the underside of half the reed block in order to silence one row or set of reeds while working on the other.

3. Small pieces to block off the bellows pins holes to stop air loss on the tuning bellows.

4. Small pieces the size of the reed plate to silence an individual reed plate. This is the Marc Serafini method: apply the tape to the reed plate directly over the reed tongue and valve and smooth the tape over the edge of the reed plate. This is really useful to silence individual reeds e.g. in chords, while you work on the others. Be sure to reduce the tackiness first. To remove, just lift carefully from the rivet end of the reed and peel off in a parallel movement, like peeling a banana. Hold down the valve with a finger as you peel.
« Last Edit: November 14, 2020, 07:52:45 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tool Kit for melodeons
« Reply #23 on: November 14, 2020, 07:50:08 AM »

Other sundries:

Sharp scissors for trimming valves, etc.

Sharp craft knife or scalpel

Cocktail sticks for applying glue, adjusting the set of reed tip gap, etc.

Solvent-free contact adhesive for fixing valves

Cyano-acrylate 'superglue': Great for fixing worn, enlarged, threads in wood screw holes or enlarged bellows pins holes. Just put a drop of superglue on the tip of a cocktail stick and run it around the inside of the hole. Remove cocktail stick before the glue sets. Repeat if necessary.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Tool Kit for melodeons
« Reply #24 on: November 14, 2020, 10:18:53 AM »

I'm not very practiced in the art of investigating the bowels of a melodeon.
It is usually ( only! ) been restricted to freeing a reed from a speck of dust.
My tools are my trusty piece of wood, an end cutter with a hole filed to fit the bellows pins, a small set of pliers as sometimes easier to remove the pins..... and a new £5 or £10 note.
I find if I gently feed the edge of a bank note in under the reed tongue and pull it back it is sufficient to dislodge and dust in between the reed tongue and the reed frame.

A friend introduced me to the bank note idea, in my concertina days and I vividly remember my first real concertina being reduced to bits in a cafe in Exeter, then being asked for a bank note and realising to my relief that the re-assembled concertina now worked as before!
Dunno what the assembled expert fettlers think, but it has been my 'go to' speck removing tool  (:)
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tool Kit for melodeons
« Reply #25 on: November 14, 2020, 11:41:44 AM »

...I find if I gently feed the edge of a bank note in under the reed tongue and pull it back it is sufficient to dislodge and dust in between the reed tongue and the reed frame.

A friend introduced me to the bank note idea, in my concertina days and I vividly remember my first real concertina being reduced to bits in a cafe in Exeter, then being asked for a bank note and realising to my relief that the re-assembled concertina now worked as before!
Dunno what the assembled expert fettlers think, but it has been my 'go to' speck removing tool  (:)

Sounds good to me!

With any sort of melodeon or concertina work (or any other instrument repair) I always think of, and try to abide by, the paraphrase of the Hippocratic Oath: Primum non nocere; First, do no harm.

If it does no harm and if it works, then it's OK!  (:)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Tool Kit for melodeons
« Reply #26 on: November 14, 2020, 11:43:03 AM »

Probably my most "handy" improvisation is a set of feelers. I've filed down the tip of an 8 thou blade, so that it slides easily beneath and between the reeds on top their plates for use as a support while cleaning or tuning and also for "pinging". Then I use a 2 or 3 thou one for sliding along the sides of reeds, when depressed into their slot, to check for clearance and/or to clear any debris, also for adjusting the reed sideways in the slot. Or a thicker one when the reed is displaced enough to not actually fit into the slot.
I expect that the professionals might be horrified at me using steel implements in case they damage something, but I'm reasonably careful and I find them invaluable, and very cheaply replaced at car boot sales and the like for 50p or so!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tool Kit for melodeons
« Reply #27 on: November 14, 2020, 11:47:25 AM »

Probably my most "handy" improvisation is a set of feelers. I've filed down the tip of an 8 thou blade, so that it slides easily beneath and between the reeds on top their plates for use as a support while cleaning or tuning and also for "pinging". Then I use a 2 or 3 thou one for sliding along the sides of reeds, when depressed into their slot, to check for clearance and/or to clear any debris, also for adjusting the reed sideways in the slot. Or a thicker one when the reed is displaced enough to not actually fit into the slot.
I expect that the professionals might be horrified at me using steel implements in case they damage something, but I'm reasonably careful and I find them invaluable, and very cheaply replaced at car boot sales and the like for 50p or so!

No, not at all. Steel feeler gauges are good. I think the steel used for reed tongues is tempered harder than the feeler blades, so little risk of damage. So long as you go carefully (Primum non nocere), you'll be OK.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

arty

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1465
Re: Tool Kit for melodeons
« Reply #28 on: November 14, 2020, 12:12:43 PM »

Shouldn’t there be a box of Yorkshire tea in your tool kit?
Logged
Pre-Pokerwork C/F, Castagnari Laura G/C, Beltuna Sara 3 A/D, Castagnari Sander Special D/G

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Tool Kit for melodeons
« Reply #29 on: November 14, 2020, 12:19:21 PM »

"I think the steel used for reed tongues is tempered harder than the feeler blades"

I had imagined that this was the case, thanks for confirming that, Steve.

"Shouldn’t there be a box of Yorkshire tea in your tool kit?"

Where's that shuddering emoji? No no, arty, I cannot stomach that stuff, give me a nice mild Ceylon or possibly a Darjeeling (Single Estates, of course!) My doc has just told me that I should cut down on the tea and drink more plain water, but he's obviously as daft as a brush!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

playandteach

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3526
  • Currently a music teacher in a high school.
Re: Tool Kit for melodeons
« Reply #30 on: November 14, 2020, 03:22:46 PM »

My doc has just told me that I should cut down on the tea and drink more plain water, but he's obviously as daft as a brush!
When mine said something similar it was to avoid the biscuit temptation.
Logged
Serafini R2D2 GC, Serafini GC accs 18 bass

Andy Next Tune

  • aka Andy Wooles
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1127
  • Melodeon with Accidentals? Make a PI Claim!!!
    • www.shavethedonkey.co.uk
Re: Tool Kit for melodeons
« Reply #31 on: November 14, 2020, 03:55:58 PM »

Nobody has mentioned a good source for the 'magic dust' that most professional fettlers have in their tool kit.
Someone said you can only get it from the well of experience, but......?
Logged
Andy, from the now ex-County Palatine of Cheshire

Caring for a European community of melodeons from France, Italy, Germany, Wales and Suffolk!

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Tool Kit for melodeons
« Reply #32 on: November 14, 2020, 04:53:41 PM »

Nobody has mentioned a good source for the 'magic dust' that most professional fettlers have in their tool kit.
Someone said you can only get it from the well of experience, but......?

I've tried it but found it messy. It clogs up the reeds.
On the other hand, this works a treat.
Logged

Thrupenny Bit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 7232
  • happily squeezing away in Devon
Re: Tool Kit for melodeons
« Reply #33 on: November 14, 2020, 04:56:28 PM »

 ;D
Of course, why didn't I think of that!!
Logged
Thrupenny Bit

I think I'm starting to get most of the notes in roughly the right order...... sometimes!

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Tool Kit for melodeons
« Reply #34 on: November 14, 2020, 06:44:01 PM »

Is that for the high notes, Pearce? Ooooooh!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Tool Kit for melodeons
« Reply #35 on: November 14, 2020, 07:11:01 PM »

Some of the pliers I use:
A) rod/lever bending pliers

Scott
Logged
too many boxes...please buy one, or two, or

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Tool Kit for melodeons
« Reply #36 on: November 14, 2020, 07:16:34 PM »

B) spring compression/insertion pliers

Allows replacement of springs without pulling axle.
Logged
too many boxes...please buy one, or two, or

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Tool Kit for melodeons
« Reply #37 on: November 14, 2020, 07:23:26 PM »

C & G  Pin pulling pliers & pin hole reamers

Phenolic jaws prevent damage to soft brass pin heads like Castagnari.
« Last Edit: November 14, 2020, 07:25:34 PM by hickory-wind »
Logged
too many boxes...please buy one, or two, or

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Tool Kit for melodeons
« Reply #38 on: November 14, 2020, 07:28:02 PM »

G) making pin puller with diamond sphere rotary tool
Logged
too many boxes...please buy one, or two, or

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Tool Kit for melodeons
« Reply #39 on: November 14, 2020, 07:30:46 PM »

D) convex / concave jaws for making small angle 'dent' in round rods and flat levers.
Logged
too many boxes...please buy one, or two, or
Pages: 1 [2] 3 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal