Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Clip-on microphones  (Read 4652 times)

0 Members and 1 Guest are viewing this topic.

hionay

  • Member
  • *
  • Offline Offline
  • Posts: 10
Clip-on microphones
« on: November 23, 2020, 06:04:59 PM »

Hello,

I have two mounts built for clip-on microphones at right and left side on my accordion as you see from the attachments.

I bought two AKG C516 ML microphones recently and have thought that I can mount them on my accordion without the adhesive plates.
Then I realized that C516 doesn't have clamps to install to mounts on my accordion.

Do you know any kit (with clamp) that works with C516? I don't want to use adhesive plates.

I saw a universal clip on Thomann ( https://www.thomann.de/intl/the_tbone_ovid_system_universal_clip.htm )
But shipping fees to my country are higher than the product price (30 EUR).
Logged

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: Clip-on microphones
« Reply #1 on: November 23, 2020, 08:42:00 PM »

I use one of those mikes. It didn't come with an adhesive plate, but with a mounting plate with two screw holes. Not wanting to drive screws into my box, I attach the mounting plate temporarily to the top of my treble cabinet with some of that squishy stuff that you can buy in a stationery shop for attaching posters to walls. Then clip the mike in. Works fine for my purposes.
« Last Edit: November 23, 2020, 08:46:51 PM by Stiamh »
Logged

Mac Gasking

  • Member
  • *
  • Offline Offline
  • Posts: 4
Re: Clip-on microphones
« Reply #2 on: November 24, 2020, 08:36:11 AM »

Not wanting to drill holes or use sticky tape here is my solution.  I have used two TIE microphones but beware you will need to provide low voltage phantom power through miniature XLR connectors.  Castagnari thoughtfully provided some press studs top and bottom and both sides. I used a 3d printer for the mounts but leather would probably do it.  Sounds ok.
Logged

Julian S

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1628
  • D/G Pastourelle 2, Dony, Pokerwork, G/C Pariselle
Re: Clip-on microphones
« Reply #3 on: November 24, 2020, 08:57:11 AM »

I use a patch of heavy duty velcro - one on top of each box and one on the AKG mount, for treble. Very easy to move the microphone between boxes. A cheapish Thomann tieclip mike for bass (which has a mini xlr compatible with the AKG beltpack).
I suppose taking off the velcro could damage the finish on the box, but I haven't tried that so we'll see.

J
Logged
Old Bones Dance Band

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Clip-on microphones
« Reply #4 on: November 24, 2020, 09:04:11 AM »

I suppose taking off the velcro could damage the finish on the box, but I haven't tried that so we'll see.


The usual problem is not actual damage to the box but the piece of casework covered by the velcro will not darken as much as the rest of it over time so a pale patch gets left behind.

Julian S

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1628
  • D/G Pastourelle 2, Dony, Pokerwork, G/C Pariselle
Re: Clip-on microphones
« Reply #5 on: November 24, 2020, 09:38:01 AM »

I suppose taking off the velcro could damage the finish on the box, but I haven't tried that so we'll see.


The usual problem is not actual damage to the box but the piece of casework covered by the velcro will not darken as much as the rest of it over time so a pale patch gets left behind.

That's useful to know - but that would probably also apply if I had screwed the mounting plate on.
I'm a bit more concerned about possible damage to my Castagnari with nice wood finish than my ageing Saltarelle's battered ply !
As there is little prospect of needing to mike up the instrument for some time yet - if ever, maybe I should carefully remove the patch anyway.

J
Logged
Old Bones Dance Band

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: Clip-on microphones
« Reply #6 on: November 24, 2020, 02:47:03 PM »

I suppose taking off the velcro could damage the finish on the box, but I haven't tried that so we'll see.


The usual problem is not actual damage to the box but the piece of casework covered by the velcro will not darken as much as the rest of it over time so a pale patch gets left behind.

That's useful to know - but that would probably also apply if I had screwed the mounting plate on.

The squishy poster-putty stuff I use is very easy to remove after every gig. No visible effect on the wood of my Saltarelle after being left on for the best part of a year.

Howard Jones

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1203
Re: Clip-on microphones
« Reply #7 on: November 24, 2020, 02:55:33 PM »

The AKG C519 M is a similar mic with a clip.  It's described as being for wind instruments but that could be because of the clip, and the mic specs look very similar and I suspect are the same capsule.  However I've not tried it, I have a C516M but had few qualms about screwing the mount onto my battered Saltarelle.  If you've only just bought the 516s, would your retailer swap them?

You've said you don't want to use the adhesive mounts, but couldn't you fasten them onto the wooden mounts you've added to your instrument?  This wouldn't risk damage to the instrument casework, but if necessary the wooden mounts could be replaced.  Alternatively, AKG do a special putty for temporarily attaching mics to instruments which is usually included in the box and which works fairly well. 

I think the Thomann clip is universal for their Ovid range, and might not work with a different brand. You might lose quite a bit of length off the gooseneck to allow room for the bracket on the end of the mic.

hionay

  • Member
  • *
  • Offline Offline
  • Posts: 10
Re: Clip-on microphones
« Reply #8 on: November 26, 2020, 05:53:14 PM »

Thanks for all your suggestions. Sorry, I have been really busy and couldn't reply.

I use one of those mikes. It didn't come with an adhesive plate, but with a mounting plate with two screw holes. Not wanting to drive screws into my box, I attach the mounting plate temporarily to the top of my treble cabinet with some of that squishy stuff that you can buy in a stationery shop for attaching posters to walls. Then clip the mike in. Works fine for my purposes.
Mine came with an adhesive plate but I can't use it because it falls off after 5mins playing. I think I need better adhesive plates. I will try another brands.


Not wanting to drill holes or use sticky tape here is my solution.  I have used two TIE microphones but beware you will need to provide low voltage phantom power through miniature XLR connectors.  Castagnari thoughtfully provided some press studs top and bottom and both sides. I used a 3d printer for the mounts but leather would probably do it.  Sounds ok.
These are really good but I don't have a 3d printer. Firstly I want to try putting these mics with a clip to mounts which Castagnari built to the top of treble. I also bought t-bone battery pack which provides phantom power.


I use a patch of heavy duty velcro - one on top of each box and one on the AKG mount, for treble. Very easy to move the microphone between boxes. A cheapish Thomann tieclip mike for bass (which has a mini xlr compatible with the AKG beltpack).
I suppose taking off the velcro could damage the finish on the box, but I haven't tried that so we'll see.

J
I found these products. Are they suitable for AKG H516 mount? If yes, I'll buy these and extra H516 mounts for my another accordion.
https://www.thomann.de/intl/velcro_klettverschluss_hakenband.htm
https://www.thomann.de/intl/velcro_klettverschluss_oesenband.htm


The usual problem is not actual damage to the box but the piece of casework covered by the velcro will not darken as much as the rest of it over time so a pale patch gets left behind.
What do you suggest to avoid this problem? Does taking off and putting new velcro pads for every recording work?


The AKG C519 M is a similar mic with a clip.  It's described as being for wind instruments but that could be because of the clip, and the mic specs look very similar and I suspect are the same capsule.  However I've not tried it, I have a C516M but had few qualms about screwing the mount onto my battered Saltarelle.  If you've only just bought the 516s, would your retailer swap them?

You've said you don't want to use the adhesive mounts, but couldn't you fasten them onto the wooden mounts you've added to your instrument?  This wouldn't risk damage to the instrument casework, but if necessary the wooden mounts could be replaced.  Alternatively, AKG do a special putty for temporarily attaching mics to instruments which is usually included in the box and which works fairly well. 

I think the Thomann clip is universal for their Ovid range, and might not work with a different brand. You might lose quite a bit of length off the gooseneck to allow room for the bracket on the end of the mic.
I have seen C519 mics after receiving C516 mics. I bought C516 mics from Thomann. Shipping fees are really expensive there to my country. Also C519 is more expensive than C516. So I didn't want to deal with shipping fees for returning the product back to Thomann.
I tried to fasten the H516 to the wooden mount but then I couldn't plug the mic because wooden mount blocks the front of the mic input.

Maybe Ovid universal clip will work, I don't know. I have to try it. Ovid CC 100's gooseneck length is 13cm which is used with Ovid clip. My C516's gooseneck length is 20cm.

I consider buying Ovid universal clip and Velcro pads.
https://www.thomann.de/intl/velcro_klettverschluss_hakenband.htm
https://www.thomann.de/intl/velcro_klettverschluss_oesenband.htm

One of them will work IMO. What do you think?
Logged

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: Clip-on microphones
« Reply #9 on: November 26, 2020, 06:32:21 PM »

I use one of those mikes. It didn't come with an adhesive plate, but with a mounting plate with two screw holes. Not wanting to drive screws into my box, I attach the mounting plate temporarily to the top of my treble cabinet with some of that squishy stuff that you can buy in a stationery shop for attaching posters to walls. Then clip the mike in. Works fine for my purposes.
Mine came with an adhesive plate but I can't use it because it falls off after 5mins playing. I think I need better adhesive plates. I will try another brands.

This is the kind of stuff I am talking about. The brand I've been using is white. I put a good blob under the mounting plate and squish it down. It stayed firmly in place for a year of gigging with no danger of falling off. No marks, no holes, no glue.

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Clip-on microphones
« Reply #10 on: November 26, 2020, 06:53:30 PM »

The Staples stuff is a Blue Tack clone. What brand do you use, I wonder?
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: Clip-on microphones
« Reply #11 on: November 26, 2020, 08:35:08 PM »

The Staples stuff is a Blue Tack clone. What brand do you use, I wonder?

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Clip-on microphones
« Reply #12 on: November 26, 2020, 09:15:43 PM »

Thanks Stiamh. Are they individual sticky pads, or a kneadable putty?
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: Clip-on microphones
« Reply #13 on: November 26, 2020, 09:27:44 PM »

Thanks Stiamh. Are they individual sticky pads, or a kneadable putty?

They come as little squares on backing paper in the packet, but they do indeed combine readily into a kneadable putty. Which dries out somewhat over time, improving the grip, but still comes off easily enough. First and only kind I've tried - it's what was in the local stationer's.  (:)

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Clip-on microphones
« Reply #14 on: November 26, 2020, 09:36:39 PM »

Thanks Stiamh. Are they individual sticky pads, or a kneadable putty?

They come as little squares on backing paper in the packet, but they do indeed combine readily into a kneadable putty. Which dries out somewhat over time, improving the grip, but still comes off easily enough. First and only kind I've tried - it's what was in the local stationer's.  (:)

I think they're just called Prit Pads here. I've used them and Blue Tack. I'm pretty sure the Prit Pads are a lot stickier (if I'm right and that's actually what they are).
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Joan Kureczka

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 195
Re: Clip-on microphones
« Reply #15 on: September 12, 2023, 06:42:31 PM »

My husband, who has a lot of experience with blu tack (for mineral specimens), says it WILL leave a residue that sinks down into stuff and recommends I not try it. Sounds like your white brand doesn't offer the same risk.
Logged
MAD: GD Oakwood Baffetti Super II, GD Loffet Pro, GD Oakwood 3-voice, CG Castagnari Sander, CG Salterelle Pastourelle II, GD Saltarelle Pastourelle II, Smythe "Flea," and a crazy blinged up Pokerwork

melod-ian

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 295
Re: Clip-on microphones
« Reply #16 on: September 13, 2023, 07:51:06 PM »

I had a bit of a eureka moment last night.
I’ve been using a clip (a Shure PGA98H-XLR) on my Acadian for ages. I’ve just started playing a bit of English music again, so spent ages trying to work out what kind of fitting solution I could get for my Baffetti.

I thought… just take the grill off! There’s I little block of wood the holds that holds the grill in place with the screw pin, also a perfect place to clip on the mic!

Until I find a more attractive alternative, it worked well.
« Last Edit: September 13, 2023, 07:53:43 PM by melod-ian »
Logged
3 x Acadian's (C,Bb,A),
Hohner corona iiir (GCF)
PS Black Pearl (DG)
and the old hohner erica (DG)
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal