Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Blocks again?  (Read 1915 times)

0 Members and 1 Guest are viewing this topic.

Stockaryd

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 255
Blocks again?
« on: December 05, 2020, 11:59:59 PM »



Whats your opinion?
Is this construction of blocks worse or better or equivalent to ordinary blocks?
Pro and cons?

http://www.machineconcepts.co.uk/accordion/accordion_project.htm

Logged
Hohner Corso, Hohner Erica, Emmanuel Pariselle, Gessner,   Koch,   Mariotti,    "China  NoName",   4 Toy,     -and now some more

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Blocks again?
« Reply #1 on: December 06, 2020, 12:22:13 AM »

At a guess - given that the centre plate is effectively a 'baffle' which directs the air via a reduced chamber on suck and blow, without the baffle it will be affected by the weaker of the reed blades/least efficient valve and it will simply not be as efficient.  It may slow one or more of the reeds speaking and will make any slides ( potentially) redundant if applicable.

Funny stuff 'air' - porting carbs confirms that.

Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Blocks again?
« Reply #2 on: December 06, 2020, 12:36:57 AM »

This is probably quite naughty; but to reduce or increase the volume and starting of a particular read in an unbaffled set, I have had some success by reducing or enlarging the valve opening by the judicial addition of valve glue.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Blocks again?
« Reply #3 on: December 06, 2020, 01:30:52 AM »

At a guess - given that the centre plate is effectively a 'baffle' which directs the air via a reduced chamber on suck and blow, without the baffle it will be affected by the weaker of the reed blades/least efficient valve and it will simply not be as efficient.  It may slow one or more of the reeds speaking and will make any slides ( potentially) redundant if applicable.

Funny stuff 'air' - porting carbs confirms that.

Yes - I agree with Nigel's analysis.
Also, without the centre partition to enable isolation of the L and M reeds, fine tuning in situ would be a real pain. It could be done by using masking tape directly applied to the reed plates to silence each of the reeds in turn, although I try to minimise this as much as possible to avoid potential damage to the valves.

In partly similar setting, the shared bass/chord reeds on earlier Castagnari Tommys have no partition between the sides of the reed blocks and they are always awkward to tune; they can never be done totally accurately - always a compromise. You can get the bass reed in tune or the relevant shared chord reed in tune, but when sounded together the pitches change slightly (around 5 - 6 cents) because of the effectively altered dimensions of the reed chamber.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Blocks again?
« Reply #4 on: December 06, 2020, 09:17:53 AM »

Does anyone know how this project worked out?
I thought of suggesting a bisonoric bass end, then I noticed the date.
[and then I read the spec]
« Last Edit: December 07, 2020, 01:49:03 PM by Tone Dumb Greg »
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Blocks again?
« Reply #5 on: December 07, 2020, 12:21:16 AM »

If you mean the block that has a sort of triangular cross section? The main thing is that the reeds themselves would need to be mounted with the rivet at the top, so that there is some clearance for the tongue as it oscillates into the chamber itself. Mounted normally it’s doubtful the Reed would function. I’m not convinced it would work even with the rivet at the top. I was looking at a Hohner Arietta bass block today and the bass chamber actually tapers wider towards the reed tip.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Blocks again?
« Reply #6 on: December 07, 2020, 01:02:03 AM »

If you mean the block that has a sort of triangular cross section? The main thing is that the reeds themselves would need to be mounted with the rivet at the top, so that there is some clearance for the tongue as it oscillates into the chamber itself. Mounted normally it’s doubtful the Reed would function. I’m not convinced it would work even with the rivet at the top. I was looking at a Hohner Arietta bass block today and the bass chamber actually tapers wider towards the reed tip.

Mounting the reeds with the rivet at the top would also make it very difficult for tuning. It's hard enough when there are just one or two mounted this way which is often found on the smallest, highest pitched, reeds on a conventional reed block. All of the reeds mounted this way would be a nightmare.  :(
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Blocks again?
« Reply #7 on: December 07, 2020, 08:36:47 AM »

I hadn’t even thought of that. So the answer to the question...will this design work? Is no, it won’t.
As a little addendum, in the summer I tuned a set of reeds for a hand built hybrid Bandoneon/concertina instrument, and the owner hadn’t quite left enough clearance at the top of Reed chambers for the largest reeds. As it happens the solution was to make a hole/open out the chamber to allow the valve and Reed enough room to oscillate. No couplers were involved so this did work ok. Otherwise I’d have set the reed with the tip leaning outwards, to gain enough clearance (provided there would have been enough clearance with the adjacent block and or casing).

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Blocks again?
« Reply #8 on: December 07, 2020, 12:51:05 PM »

Well - it appears that in early 2017 he was going to fit a set of reeds to those blocks and try them....   So by now he will certainly have discovered that reeds, with their installation, interactions and tuning,  can provide a lifetime of learning, frustration, nuances, quirks and occasional strangeness all on their own compared to which the rest of the instrument seems very straightforward.

I'd be fascinated to know.
Logged

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Blocks again?
« Reply #9 on: December 07, 2020, 01:34:19 PM »

If the weight of the blocks - compared to that of the reeds they hold, or the rest of the instrument mattered to that extent - then there would be load's of "Phil The Drill"s (vintage fishing reel reference) out there, attacking cases, blocks and any and every other component they could get their hands on to take away material with 'through and throughs' where it didn't matter and part way, wide bore, drilling of blocks, cases and fitments where it did, to lighten them.

The Socin, 8 bass, 23 button 3 voice, without registers, weighs 6.6Kg! - it's twice as 'big' physically as a Dony and weighs 1.2Kg more than a Mory, with a lot less buttons and doubles as a Tank Trap!  If ever there was a candidate for the drill, it would be one!

Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Blocks again?
« Reply #10 on: December 21, 2020, 06:51:44 AM »

This person has a long road to walk.
Using a Scarlatti as a base model for improvements is a bit like looking at a 1950's car and wondering if you can make improvements.
 This is a problem that Weltmeister hired me to look at. You run into problems with mass being removed in the wrong spot and it affecting the tuning. it becomes important to use bridges between reed blocks to share apparent mass (those little plates between reed blocks on button accordions) to prevent harmonics. I made a set of Magnesium bass reed plates and made magnesium key arms and I tried replacing steel with titanium. These all work but require very different methods of manufacture.
 It is really like making a racing bike or a space ship.
Mag is interesting ,it looks like aluminum but behaves more like acrylic plastic. Try to do much bending at room temp and it breaks, heat it to about 275.F and it bends like lead, let it cool and it is hard again.
 The fun part was it was nearly impossible to buy in the USA. I made the bass reed plates out of some scrap blocks we had at SRL and we had fun lighting the shavings on fire in the parking lot and then hitting them with the pressure washer.
 The arms were done in Germany with metal they ordered.
There really is no low hanging fruit when it comes to reducing weight. It is going to be a bit here and there.
 Bell and Wurlitzer played around with magnesium, I have seen mag bass reeds in both of these (only twice in 25 years) and Wurlitzer made a stamped magnesium body instrument (similar to hohner atlantic in construction) it was quite light. It was late in Wurlitzer's run so I have no idea how common they were.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

playandteach

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3526
  • Currently a music teacher in a high school.
Re: Blocks again?
« Reply #11 on: December 21, 2020, 11:38:28 AM »

If the weight of the blocks - compared to that of the reeds they hold, or the rest of the instrument mattered to that extent - then there would be load's of "Phil The Drill"s (vintage fishing reel reference) out there, attacking cases, blocks and any and every other component they could get their hands on to take away material with 'through and throughs' where it didn't matter and part way, wide bore, drilling of blocks, cases and fitments where it did, to lighten them.

The Socin, 8 bass, 23 button 3 voice, without registers, weighs 6.6Kg! - it's twice as 'big' physically as a Dony and weighs 1.2Kg more than a Mory, with a lot less buttons and doubles as a Tank Trap!  If ever there was a candidate for the drill, it would be one!
Drillium was a common bike mod too, before carbon etc. Problem is of course that there's a mass worldwide market in bike sales, where weight equals performance gains that are measured in wins.
Logged
Serafini R2D2 GC, Serafini GC accs 18 bass

Calum

  • Good talker
  • **
  • Offline Offline
  • Posts: 97
Re: Blocks again?
« Reply #12 on: December 21, 2020, 01:22:00 PM »

I don't know Mike well personally but have lots of connections with him through mutual interests in piping and he's a very talented engineer and musician.  If anyone is interested in this kind of thing I'd strongly encourage them to get in touch with him and offer feedback - I am pretty sure it would be welcomed with open arms.  I've no idea if traditional designs can be improved upon but a fresh set of eyes can do no harm. 
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Blocks again?
« Reply #13 on: December 22, 2020, 06:29:00 PM »

 "Problem is of course that there's a mass worldwide market in bike sales, where weight equals performance gains that are measured in wins."

I think I have an idea, accordion music contests should be like a biathlon, where you will need to run a distance , perform then run again. This should provide the proper incentive.

I did the drillium thing on some steel parts that we replaced with titanium. The parts would need to be cut with water jet since the stamping dies would be dulled by the Ti and the holes would still need to be made.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Blocks again?
« Reply #14 on: December 22, 2020, 08:10:28 PM »

"run a distance , perform then run again."

Are you nuts? I'd need some syrup of figs to do that, it would be the only way!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal