Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: In praise of "Step drills"  (Read 1355 times)

0 Members and 1 Guest are viewing this topic.

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
In praise of "Step drills"
« on: December 06, 2020, 01:23:48 PM »

I dare say everyone knows all about these and has done for years.  I didn't.  For drilling medium to larger holes individually or en masse, in ply and the like, they are excellent.  They self centre as they go, so don't need a pilot - although one can be used if needs be - and cut a nice clean hole with minimal 'wrong side' break out.  It looks and feels counter intuitive to be using such a big chunk of metal to drill small, neat holes, but they do.   A wrap of tape around the 'step' above where you want to stop protects the job from ageing eyesight.

https://cdn.aws.toolstation.com/images/141020-UK/800/78333.jpg
Logged

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: In praise of "Step drills"
« Reply #1 on: December 06, 2020, 01:39:45 PM »

I've long used them for making big holes in sheet metal, for similar reasons of accuracy and clean cut. I can't remember if I have ever used one on wood.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Dave Praties

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 195
Re: In praise of "Step drills"
« Reply #2 on: December 06, 2020, 03:15:32 PM »

Hmmm, not sure about step drills. The problem with self piloting is that the drill will be influenced by any slight variation in hardness, encountered in all timber, but especially plywood, and will not centre where you intend. Unless you drive it very slowly in a pillar drill, with the workpiece held very securely. The only way to ensure zero break-out, very important when making a fondo Etc., is to pilot carefully with a small drill, then drill from both sides with a suitable wood bit. Backing with timber can work, but with variable results. Just my experience though, quite prepared to be proved wrong.
Logged
Castagnari Handry 18 G/C. Castagnari Handry 18 D/G.    Self-built G/C 2.5/12 bass. almost finished after 7 years! Bb/Eb Preciosa. C/F Lilliput.

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: In praise of "Step drills"
« Reply #3 on: December 06, 2020, 07:09:48 PM »

It strikes me as unlikely that local hardspots would offset a drill by more than the allowable tolerance for a fondo - but what do I know?  I would seriously suggest that anyone doing this should use a pillar drill and set up a simple jig to clamp the workpiece to give regular spacing and true alignment of the holes.  Starting from both sides does prevent damage from breakout - even in metals, but moreso in organic matter like wood.

I'm not sure which is more common, but I've seen step drills with sharp steps and a few with a radiused transition between steps - presumably intended for use on different materials.  One of the other advantages of a pillar drill is that the depth stop can be used to ensure the next step can't touch the surface unintensionally.  Backing with timber can only work reliably if pressure can be maintained between the workpiece and backing.  Soft or particularly brittle materials (which includes plywood) work out best if clamped very tightly between two backing pads until the work is finished in my experience.

Rob.
Logged

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: In praise of "Step drills"
« Reply #4 on: December 06, 2020, 07:19:30 PM »

Dave, my experience is the opposite, knots in particular will cause an 1/8th or 1/4 pilot drill to veer, mainly due to their lack of beam strength and bending, the step drill is effectively guided by most of the circumference and as the steps are typically around 5mm deep they are rigid, there are stepless conical equivalents available known interestingly as cone cuts.

Another benefit in sheet materials is they are not prone to the oversize and non circular holes often caused at breakthrough, particularly if a helical drill has disimilar cutting edges.

Downside is they take some resharpening without a cutter grinder, I tend to hone little and often - offhand grinder sharpening ? that way lies insanity :)

A sacrificial board underneath the work piece results in almost no breakthrough tearout

A magic marker mark tends to last longer than tape if you are really shifting swarf  :||:
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: In praise of "Step drills"
« Reply #5 on: December 06, 2020, 10:57:07 PM »


A sacrificial board underneath the work piece results in almost no breakthrough tearout


Spot on.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Dave Praties

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 195
Re: In praise of "Step drills"
« Reply #6 on: December 07, 2020, 09:48:54 PM »

Dave, my experience is the opposite, knots in particular will cause an 1/8th or 1/4 pilot drill to veer, mainly due to their lack of beam strength and bending, the step drill is effectively guided by most of the circumference and as the steps are typically around 5mm deep they are rigid, there are stepless conical equivalents available known interestingly as cone cuts.

Another benefit in sheet materials is they are not prone to the oversize and non circular holes often caused at breakthrough, particularly if a helical drill has disimilar cutting edges.

Downside is they take some resharpening without a cutter grinder, I tend to hone little and often - offhand grinder sharpening ? that way lies insanity :)
Ah, ok, I seem to have missed a trick here. I confess that I have only tried a step drill once, and it produced a lot of tearing. It was an old one I found lying around, so maybe it was blunt, or possibly a cheap inferior one. I am intrigued  now, so will buy one and give it a go. Latterly, I have gone high-tech with drilling, and use a laser cutter when I can, that option carries a time penalty of course, with a CAD drawing to be done, but boy is it neat and accurate! When I retire though, that option sadly stays behind at work. Unless I can smuggle it out with the rest of my stuff!
Dave

A sacrificial board underneath the work piece results in almost no breakthrough tearout

A magic marker mark tends to last longer than tape if you are really shifting swarf  :||:
Logged
Castagnari Handry 18 G/C. Castagnari Handry 18 D/G.    Self-built G/C 2.5/12 bass. almost finished after 7 years! Bb/Eb Preciosa. C/F Lilliput.

Dave Praties

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 195
Re: In praise of "Step drills"
« Reply #7 on: December 07, 2020, 09:51:51 PM »

Sorry, I seem to have messed up that last posting. My reply is in the middle somewhere!
D
Logged
Castagnari Handry 18 G/C. Castagnari Handry 18 D/G.    Self-built G/C 2.5/12 bass. almost finished after 7 years! Bb/Eb Preciosa. C/F Lilliput.

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: In praise of "Step drills"
« Reply #8 on: December 08, 2020, 10:46:43 AM »

Found it Dave ;)  Water jet cutting can be even better than laser but perhaps not on a fondo or other wood ;)

Excellent in a drill press, step drills are fine hand held in a cordless which may have an advantage in portability that laser doesn't but you are limited to the sheet thickness you get one diameter of hole in.

In thin metal sheet the next step up to the size you drill will nicely deburr the edge of the hole.

Horses for courses as with most tools

 
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: In praise of "Step drills"
« Reply #9 on: December 08, 2020, 12:45:42 PM »

For drilling fondos the best tool is a Forstner bit.
Drill a small pilot hole. Go halfway through with the Forstner, flip it over and drill from the other side.
I have done many hundreds of these and this method always achieves clean sharp edges.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: In praise of "Step drills"
« Reply #10 on: December 08, 2020, 12:55:32 PM »

For drilling fondos the best tool is a Forstner bit.
Drill a small pilot hole. Go halfway through with the Forstner, flip it over and drill from the other side.
I have done many hundreds of these and this method always achieves clean sharp edges.

I agree; I do use a step drill on metal and plastics from time to time, but never tried it in wood, where I always use a Forstner or a sawtooth bit.
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal