Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: adhesive for pads  (Read 1865 times)

0 Members and 1 Guest are viewing this topic.

Rick St. John

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 193
adhesive for pads
« on: December 19, 2020, 12:55:44 PM »

On an old box some of the pads are coming away from the metal levers as shown in the pic. What sort of adhesive would be best to re-attach them?
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: adhesive for pads
« Reply #1 on: December 19, 2020, 10:29:52 PM »

Do you need to glue felt to metal (pad came partially off) or felt to felt (pad delaminated) ?  It's hard to tell from the picture.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: adhesive for pads
« Reply #2 on: December 20, 2020, 12:51:22 AM »

I would recommend a thin smear of contact adhesive, solvent-free if you can get it. Then let the spring of the lever against the pallet board hold it all in place until the glue has set.

Contact adhesive is effective and remains slightly flexible, which is good in this case as it helps maintain an airtight seal. It is also relatively easy to remove if you need to do so at some future point, e.g. to renew all the pallet facings ('pads'). Don't use a permanent adhesive such as superglue or epoxy.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: adhesive for pads
« Reply #3 on: December 20, 2020, 08:15:28 AM »

PVA would do it, as would UHU or it’s equivalent. Or Bostick solvent free. All easier to apply than contact (the idea of contact is that you smear a film on each (clean/dust free) surface and let it dry and then bring those surfaces together, which bind on contact. However I’m aware that many people don’t use contact adhesive in this way...they use it like a regular glue...it’s stringy and tricky to get in the right place when it’s wet).

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: adhesive for pads
« Reply #4 on: December 20, 2020, 08:36:52 AM »

PVA would do it, as would UHU or it’s equivalent. Or Bostick solvent free. All easier to apply than contact (the idea of contact is that you smear a film on each (clean/dust free) surface and let it dry and then bring those surfaces together, which bind on contact. However I’m aware that many people don’t use contact adhesive in this way...they use it like a regular glue...it’s stringy and tricky to get in the right place when it’s wet).

PVA dries too hard and you risk saturating the felt and making it hard and unresponsive. It's also difficult to remove at a later date if you need to. Bostik solvent free is a contact adhesive and would work well in this instance for joining felt to the metal pallet face.

Contact adhesive will work perfectly well here by applying a single coat to one of the surfaces. If you use a cocktail stick to carefully apply the glue sparingly it is not messy at all.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: adhesive for pads
« Reply #5 on: December 20, 2020, 09:06:02 AM »

Well that’s put me right. I'll just get my coat  ;)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: adhesive for pads
« Reply #6 on: December 20, 2020, 09:29:19 AM »

I would have no worries using pva as long as you apply only a thin film to the pallet and none to the felt.  In fact you can use just about any adhesive that can be spread thinly, the ones I would avoid would be superglue (which definitely will harden the felt, or epoxy which is far to strong and would be difficult to remove later when new pads are needed.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rick St. John

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 193
Re: adhesive for pads
« Reply #7 on: December 20, 2020, 11:59:57 AM »

Thanks for the suggestions, everyone
Logged

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: adhesive for pads
« Reply #8 on: December 20, 2020, 01:51:25 PM »

Late to the party, I searched long and hard ( and wastefully ) to find an alternative for most metal to vinyl/felt/leather jobs. (when Bostik Solvent Free was taken off the market )

I have settled on 3M 1099 Vinyl Weld, which is a solvent based contact adhesive, but, I apply it via a 5ml syringe with the blunt needle attachment.  I decant the glue from the tube into the syringe.  They are pennies on-line.

The needle is fine enough to 'heal' at the tip, so can be used/re-used/re-filled multiple times.  It also allows very fine application of glue in a 'U' shape on valve's, so fine that they do not 'pucker' from the solvent and it can be edge and zig-zagging applied for larger surfaces, with no real fumes from such a small 'open' volume.  I use it as a straight adhesive, ie. generally one surface only

I find it comes off metal with a Stanley blade.
« Last Edit: December 20, 2020, 05:57:10 PM by Nigel.H »
Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: adhesive for pads
« Reply #9 on: December 20, 2020, 05:41:36 PM »

Contact adhesive will work perfectly well here by applying a single coat to one of the surfaces. If you use a cocktail stick to carefully apply the glue sparingly it is not messy at all.

While I am happy to accept your excellent advice, Steve, I'm a bit mystified by the concept that contact adhesive will work if applied to only one surface. To me that sounds totally counter-intuitive; could you possibly enlighten us? I'm always delighted to learn......

Cheers
Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: adhesive for pads
« Reply #10 on: December 21, 2020, 08:05:53 AM »

Contact adhesive will work perfectly well here by applying a single coat to one of the surfaces. If you use a cocktail stick to carefully apply the glue sparingly it is not messy at all.
While I am happy to accept your excellent advice, Steve, I'm a bit mystified by the concept that contact adhesive will work if applied to only one surface. To me that sounds totally counter-intuitive; could you possibly enlighten us? I'm always delighted to learn......

All I can say is that it just works. Have used contact adhesive (Bostik, usually) this way for years, mainly for attaching valves to reed plates. No problem.

I do join the two surfaces together immediately after applying the glue instead of waiting a few minutes as per the usual instructions, so I suppose some of the liquid glue does get transferred to the non-glued surface and from that moment it starts to cure.

The other advantage of this method is that you get a short period of slip time (say approx. 10 seconds) in which you can slightly adjust the positioning if need be.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Stotty

  • Stotty
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 191
Re: adhesive for pads
« Reply #11 on: December 21, 2020, 09:07:22 AM »

It seems to me that the likelihood is that as solvents and "vapours" can evaporate through porous substrates, like pads, the drying process can occur with surfaces together, but at a slower rate than if both surfaces are coated and exposed to air. For smaller contact patches like valves there will be edge "evaporation" effects.
Logged

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: adhesive for pads
« Reply #12 on: December 21, 2020, 11:02:07 AM »

I struggled with most glues to find one that worked well with vinyl/felt and metal, after the Bostik "solvent free" was 'retired'.  I even found a supply in the Store in Jordan of all places, but it was collection only, so a bit prohibitive ( I would have paid for a box by post! )  I constantly found that other glues went stringy, generally came out too fast/without much control/or too great a volume.

Initial experiments with a normal syringe were 'ok' but it still 'globbed' up and 'went off' in the tip and provided too much glue, making some valves pucker and was generally not that great.  It also meant that I only got one or two sessions from a fill of the syringe ( from the tube of glue ) before it had to go in the bin.

The 5ml, thick needle syringes overcome all those issues, I find.  The glue stays 'fresh'/fluid inside the syringe and is delivered under fine control.
« Last Edit: December 21, 2020, 11:04:25 AM by Nigel.H »
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: adhesive for pads
« Reply #13 on: December 21, 2020, 01:41:57 PM »

Nigel,

I've never encountered those sorts of problems.
Bostik 'Clear' contact adhesive is what I use for valves and I've never had any problem with the valve distorting.

I use my favourite tool - a cocktail stick. I put a small blob of glue on the end of the cocktail stick and smear it in an even coating on the end of the valve, then gently press the valve into place. Job done. No messing about with syringes, etc.

I know that Lester, and also Theo I think, keep the tube of glue upright in a small vice and squeeze a small amount directly onto the valve. But I prefer the cocktail stick method. I keep my tube of glue upright in an old mug with the cap off while I'm doing the re-valving job; just a gentle squeeze on to the end of the cocktail stick.

Works for me, as the lady says. 
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: adhesive for pads
« Reply #14 on: December 21, 2020, 07:25:09 PM »

Contact adhesive will work perfectly well here by applying a single coat to one of the surfaces. If you use a cocktail stick to carefully apply the glue sparingly it is not messy at all.
While I am happy to accept your excellent advice, Steve, I'm a bit mystified by the concept that contact adhesive will work if applied to only one surface. To me that sounds totally counter-intuitive; could you possibly enlighten us? I'm always delighted to learn......

All I can say is that it just works. Have used contact adhesive (Bostik, usually) this way for years, mainly for attaching valves to reed plates. No problem.

I do join the two surfaces together immediately after applying the glue instead of waiting a few minutes as per the usual instructions, so I suppose some of the liquid glue does get transferred to the non-glued surface and from that moment it starts to cure.

The other advantage of this method is that you get a short period of slip time (say approx. 10 seconds) in which you can slightly adjust the positioning if need be.

Ah, that could explain it. FWIW, I usually use Titebond II simply because it's the adhesive I use most often in the workshop and there's always a supply of it to hand.  If I feel I need to go more "traditional" Titebond Liquid Hide Glue is pretty good. I've also used a Black Bison general purpose glue - I can't recall its name offhand and I'm not going out to a dark, cold workshop now (it's 9.20pm where I am, and I'm nearly 3000ft above sea level, so it's a bit chilly out there!) to remind myself.  In short, I guess there's a fair range of glues that will work .......

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal