Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: glued reeds block  (Read 2493 times)

0 Members and 1 Guest are viewing this topic.

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
glued reeds block
« on: December 21, 2020, 04:56:57 PM »

Hi .. advice is needed .
I inquire what a good / best way  remove Hoher's glued reeds block ? maybe hot water ?
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: glued reeds block
« Reply #1 on: December 21, 2020, 05:26:20 PM »

Hi .. advice is needed .
I inquire what a good / best way  remove Hoher's glued reeds block ? maybe hot water ?

It's best not to try. You will only cause more damage than is worth while. Why would you want to remove the reed blocks anyway?
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: glued reeds block
« Reply #2 on: December 21, 2020, 05:34:13 PM »

Hi .. advice is needed .
I inquire what a good / best way  remove Hoher's glued reeds block ? maybe hot water ?

It's best not to try. You will only cause more damage than is worth while. Why would you want to remove the reed blocks anyway?
two reeds blog, it is difficult wax reeds
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: glued reeds block
« Reply #3 on: December 21, 2020, 05:55:58 PM »

I have removed bass reed blocks on accordions where both blocks were glued in (WHY!).
I used the heated waxing knife to cut the glue joint and tiny drops of water here and there, it works but takes patience and time. Depending on the layout , a flush saw might work for stubborn bits but the saw can wander so it is not always good for bigger things.

 I also made bass plate for the block I removed and made mounts and gaskets for it because I am not an animal.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: glued reeds block
« Reply #4 on: December 21, 2020, 06:06:52 PM »

I have removed bass reed blocks on accordions where both blocks were glued in (WHY!).
I used the heated waxing knife to cut the glue joint and tiny drops of water here and there, it works but takes patience and time. Depending on the layout , a flush saw might work for stubborn bits but the saw can wander so it is not always good for bigger things.

 I also made bass plate for the block I removed and made mounts and gaskets for it because I am not an animal.

Thanks Kimric .. Tonen Reeds Block would already help if it got off ,, I have to think ::)
Logged

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: glued reeds block
« Reply #5 on: December 21, 2020, 07:26:18 PM »

I use ( for similar vintage instrument tasks ) a small, cranked, Cake Decorators palette knife.  Sharpen the edge of the blade, heat the blade on a hotplate - or whatever is to hand, and moisten the joint as you go.
Logged

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: glued reeds block
« Reply #6 on: December 21, 2020, 07:54:27 PM »

Thanks Nigel (:)
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: glued reeds block
« Reply #7 on: December 21, 2020, 10:48:15 PM »

Why anyone would go through the trouble and remove glued-in reed blocks just to make waxing "easier" is beyond me.
Logged

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: glued reeds block
« Reply #8 on: December 22, 2020, 03:10:18 AM »

Why anyone would go through the trouble and remove glued-in reed blocks just to make waxing "easier" is beyond me.

sorry when i ask,, but that's why I ask when I don't know ,,
The pitch of the Hohner 113 treble blocks is intermediate very small ,,
surely everyone else knows how to wax reeds, I do not , but I'm a hobbyist,
I thought, I would get information here about what I was doing ,,
May I ask you, what kind of tool best reeds for waxing ?? ( Hohner 113 treble Reeds) inside the box ,
I'm an old hubby, but I still want to learn
Logged

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Re: glued reeds block
« Reply #9 on: December 22, 2020, 03:50:48 AM »

Hi Dino,

I prefer the half-moon shaped wax spoon, but it does take practice.  If it's a tight space, and difficult to get at with a wax tool, you can roll or cut bits of wax into small tube shapes, and press them where you need them.  Then use a small heating tool to melt the wax.  I use a "Top Flite Trim Seal Tool" made for heat-shrinking model airplane parts.  I like it because the "low" setting is just right.  I think most tools (like woodburning pens and soldering irons) run too hot, but if that's all you have on hand, you could try to manage the temperature by turning them on and off.

If we're talking about the bass, I think it's fine to remove the block, and then either re-glue it or (even better) make a nice gasket as Kimric described.

If I understood right, this is not your situation, but if it's only one bass block that's glued, you can remove the other to get a good deal of access to it.  That's how one that I'm working on now (a little Galotta) is set up.

PS - re-reading your last post, it sounds like you're talking about the treble side reedblocks in an HA-113.  I would not remove those!   :)
« Last Edit: December 22, 2020, 03:56:48 AM by Gonk »
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: glued reeds block
« Reply #10 on: December 22, 2020, 06:50:15 AM »

yes, treble, but i think i get it done , I have to practice a bit ,, i think i need to make a suitable tool ..
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: glued reeds block
« Reply #11 on: December 22, 2020, 07:12:20 AM »

Here is what I did on the evil accordion https://www.instagram.com/p/BuxxN6sBLqZ/ .

I make a electric waxing with a brass blade that works well, I hook it to a lamp dimmer to control the heat.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: glued reeds block
« Reply #12 on: December 22, 2020, 07:38:57 AM »

Here is what I did on the evil accordion https://www.instagram.com/p/BuxxN6sBLqZ/ .

I make a electric waxing with a brass blade that works well, I hook it to a lamp dimmer to control the heat.

looks good (:) i think block removal is difficult ,, I'm afraid I'll break something :(
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: glued reeds block
« Reply #13 on: December 22, 2020, 07:52:52 AM »

My method of reed waxing on 113/114s is to apply some wax to the bottom of the reed plate with the plate out of the box and then quickly slide the reed into place before the wax hardens. Once the reed is in place I run wax down the sides of the plate and across the top using gravity. I do all this with a temperature controlled soldering iron.

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: glued reeds block
« Reply #14 on: December 22, 2020, 09:07:56 AM »

My method of reed waxing on 113/114s is to apply some wax to the bottom of the reed plate with the plate out of the box and then quickly slide the reed into place before the wax hardens. Once the reed is in place I run wax down the sides of the plate and across the top using gravity. I do all this with a temperature controlled soldering iron.

Thanks Lester  (:) :||: so  good ,, I practice first ..
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: glued reeds block
« Reply #15 on: January 02, 2021, 06:08:47 PM »

Why anyone would go through the trouble and remove glued-in reed blocks just to make waxing "easier" is beyond me.

It also makes tuning a lot easier.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: glued reeds block
« Reply #16 on: January 02, 2021, 07:14:59 PM »

I suppose it depends on individual methods of working, but I do all my tuning with the reed blocks in situ,  apart from the really coarse adjustment like tuning up from 435 to 440 where I pre-tune with the reeds off the blocks.
Four stopper boxes are almost easier to tune than typical 2 row 2 voice because the stops let you isolate every reed so easily. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: glued reeds block
« Reply #17 on: January 02, 2021, 08:30:16 PM »

If you ‘must ‘ remove the blocks acetone works OK  to dissolve the glue but you’ll damage the slides for sure, best to leave the blocks alone..I have done it on 2 Hohner 114 and both ended up in spear box.
This is how I do and works well for me -as non pro like your self-   
If you use soldering iron for waxing ; all you need is longer tip, you can make your own tip yourself from bras or suitable metal rod and bend it slightly , make sure it is longer than your reed blocks so you can apply wax from outside /top of the block     
Work one of the inside reeds first & finish waxing all 10 reeds.
use a few MM thick card to cover/mask the side you have finished, make sure card covers all your reeds and taped to stop moving(masking tape works ) so you don’t  damage any of the valves and wax..move on to other side wax& finish once you are happy remove the card and move on to outside reeds.
If you need to go over to tidy up the wax use you long tip and cover the opposite reeds with a card  as you go.
All you need is longer tip for soldering iron and L shape thick card to cover up one side of the reeds.
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: glued reeds block
« Reply #18 on: January 03, 2021, 10:28:25 AM »

If you are intent on removing the reed blocks remember that the aluminium stop-slides are an integral part of the blocks.
Unscrew the stop knobs and steel rods and remove them so that the slides are free to come out with the blocks, otherwise there is a danger of snapping the slides.
I speak from experience!
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: glued reeds block
« Reply #19 on: January 03, 2021, 11:02:07 AM »

Just out of interest, Rees; are your blocks glued or screwed?
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal