Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Cracked Bellow Frame  (Read 929 times)

0 Members and 1 Guest are viewing this topic.

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Cracked Bellow Frame
« on: January 05, 2021, 05:56:04 PM »

Cracked wooden bellow frame at the pin hole site, glue and give it a go?  Or replace the frame? 
Logged
Corona III x8

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Cracked Bellow Frame
« Reply #1 on: January 05, 2021, 06:52:35 PM »

Hard to know without a picture, but it’s not any easy site to repair.  If split along the grain it might be reinforced by one or two carefully fitted wood screws. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Re: Cracked Bellow Frame
« Reply #2 on: January 05, 2021, 07:04:38 PM »

Hard to know without a picture, but it’s not any easy site to repair.  If split along the grain it might be reinforced by one or two carefully fitted wood screws.

Photos attached.  Not sure what the previous owner did, but looks like he totally screwed up when inserting the pins.  >:(  Fortunately, it is still air tight.  But surely going to be a problem sooner or later. 

« Last Edit: January 05, 2021, 07:06:39 PM by Vallenato831 »
Logged
Corona III x8

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Cracked Bellow Frame
« Reply #3 on: January 05, 2021, 07:59:49 PM »

I would glue clamp and fill that, then relocate the actual pin to one side and drill new hole.Need to do both opersites if the eye line needs to be kept thats a cosmetic visual thing.
Logged
Mark Taylor
Folkloristmark

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Cracked Bellow Frame
« Reply #4 on: January 05, 2021, 08:01:14 PM »

I would cut out and replace that section of the frame.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 246
Re: Cracked Bellow Frame
« Reply #5 on: January 05, 2021, 08:01:52 PM »

maybe bellows pin was hammered in without frame lined up. Also I encountered same result recently from instrument being dropped. I fixed with titebond wood glue and small clamp. could also be an indication that new frame seal has been used that is deeper than original. Id just try wood glue and clamp and try and get pin in original hole. could reinforce frame along inside edge if necessary again with wood glue and thin wood (coffee stirrer or lolly stick should work). Id only consider new frame as last resort. superglue in original hole after repair might also help pin sit tight. If other 3 pins fit good you should be ok. 
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 246
Re: Cracked Bellow Frame
« Reply #6 on: January 05, 2021, 08:17:39 PM »

I would cut out and replace that section of the frame.

even better. assume you would angle the replacement piece at 45 degrees so it pulls into place? but maybe with good wood glue a straight fit would be ok?
Logged

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Cracked Bellow Frame
« Reply #7 on: January 05, 2021, 08:21:53 PM »

I  would drill through both holes, then pare down  a piece of wood to fit the holes, and insert the wood with superglue, which will osmose along the crack. Once dried, tidy up and sand, then with the bellows frame in the box, mark the spot for a new hole, using the existing hole in the carcase of the box as a guide, take frame out again, and drill new hole, of the appropriate size.
Make sure the frame is tight, when marking the new hole position. I usually remove the old gasket before I mark the position, then the new gasket will be compressed properly, when refitted.
SJ
« Last Edit: January 05, 2021, 08:25:03 PM by John MacKenzie (Cugiok) »
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Cracked Bellow Frame
« Reply #8 on: January 05, 2021, 08:31:51 PM »

I would cut out and replace that section of the frame.
Absolutely!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Cracked Bellow Frame
« Reply #9 on: January 05, 2021, 09:20:26 PM »

I would cut out and replace that section of the frame.
Absolutely!

Agreed.  All the other suggestions will lead to this.  Best do a proper job first time.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Vallenato831

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 201
Re: Cracked Bellow Frame
« Reply #10 on: January 06, 2021, 04:59:22 PM »

maybe bellows pin was hammered in without frame lined up. Also I encountered same result recently from instrument being dropped. I fixed with titebond wood glue and small clamp. could also be an indication that new frame seal has been used that is deeper than original. Id just try wood glue and clamp and try and get pin in original hole. could reinforce frame along inside edge if necessary again with wood glue and thin wood (coffee stirrer or lolly stick should work). Id only consider new frame as last resort. superglue in original hole after repair might also help pin sit tight. If other 3 pins fit good you should be ok.

Yeah, those are the front 2 holes on the treble side.   The back 2 holes are perfect.  Definitely human error when inserting the pins.  I may go the wood glue route first. 

I'd love to do it the right way, cutting out that piece and gluing a new one in, but my carpentry skills are 0 to none.  Will do more harm than good.  Probably send off to an experienced technician to fix.  Appreciate all the feedback, extremely helpful.  Thanks all. 
Logged
Corona III x8
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal