Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner Ouveture IV Treble Reed Blocks  (Read 1277 times)

0 Members and 1 Guest are viewing this topic.

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Hohner Ouveture IV Treble Reed Blocks
« on: January 12, 2021, 05:59:26 PM »

I've been delving into a Hohner Ouveture IV that needs tuning and possibly a full reed overhaul. I'm not getting very far with the treble end blocks as I'm unsure about the method of construction and wary of causing damage by attempting to dismantle it in the wrong sequence. Can anyone here tell me if the stop sliders are built into the blocks instead of sitting underneath, and if so how to disengage the register mech from the blocks to get them out?
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Hohner Ouveture IV Treble Reed Blocks
« Reply #1 on: January 12, 2021, 06:02:17 PM »

The bass end reeds are monsters!  :o
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner Ouveture IV Treble Reed Blocks
« Reply #2 on: January 12, 2021, 06:45:14 PM »

Pretty sure the sliders are in the Reed blocks, so you need to lift gently on one end and carefully unhook the slider end. Or pull the block to one side and leave the slider in place, then unhook it and put it back in the block. Key thing is not to put any kinks in the slider, which is super delicate. And when putting it back in the block only push it with your fingers very close to the block. It’s very easy to bend those sliders. Getting the blocks  in and out with the sliders is a bit of a knack. The coupler mech has to fit into the slot in the end of the slider.
« Last Edit: January 12, 2021, 06:46:59 PM by RogerT »
Logged

MikeK

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 354
Re: Hohner Ouveture IV Treble Reed Blocks
« Reply #3 on: January 12, 2021, 07:02:23 PM »

 I think the sliders are the same as in The Amatona 4v boxes that I owned and as Roger has explained. In mine, I wouldn't describe the sliders
 as really delicate but ok if handled with care. If you press the correct register, it will lift and disengage the rod from the slider on the reed block
 you wish to remove.
Logged
I always respect my elders but they are getting fewer in numbers.

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Hohner Ouveture IV Treble Reed Blocks
« Reply #4 on: January 12, 2021, 07:21:14 PM »

Sliders are probably brass and much more robust than the aluminium ones.
If you do happen to kink one, sit it on a flat surface (anvil) and tap GENTLY on the kink to flatten it.  Too hard and you will flatten too much and distort it.
First thing I always do is clean the sliders so they move freely.
To replace - put slider in the reed block leaving 3" or so sticking out, hook the slider onto the reg.rod, slide the block slowly towards the reg.rod then down into place.
 If your doing a wax/retune you will get pleanty practice at this -  and at some point you will
catch a valve from the next block and have to replace that as well - it happens.
 Good luck -  John.
Logged

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Hohner Ouveture IV Treble Reed Blocks
« Reply #5 on: January 12, 2021, 07:29:03 PM »

They just lift passed the metal retainer. The christmas advent calander of the the pervious mentioned box has a good close up of that. Or you can lift the block end from the free end and slide it of the slider. Dont bend the brass and remember were it came from which block, which way round and which face . 123 vairiants. Mark them indelable marker? As for tuning with the multi voices all register options wont hold the same tuning like a MM box and leaks around the registers can make matters worse.

Its quite a complicated set up to tune.
Logged
Mark Taylor
Folkloristmark

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Ouveture IV Treble Reed Blocks
« Reply #6 on: January 12, 2021, 08:21:49 PM »

Once the reed blocks are out it’s a useful precaution to put a strip of masking tape round the bass end of the block to prevent the slide from dripping out and getting damaged.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Hohner Ouveture IV Treble Reed Blocks
« Reply #7 on: January 12, 2021, 11:06:53 PM »

Many thanks for all of the very useful replies. This sounds complicated enough to convince me that I need to leave this box to one side for the time being, it's not the kind of thing to tackle as a kitchen table project. By summer I hope to have sorted myself out with a decent workshop as part of a major project to renovated our old garage and convert it to properly usable outbuilding instead of a general junk store and bike shed.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Ouveture IV Treble Reed Blocks
« Reply #8 on: January 13, 2021, 08:05:38 AM »

It’s not really much more complicated,  but the large number of reeds means that any reed work will take a relatively long time and need extra space.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner Ouveture IV Treble Reed Blocks
« Reply #9 on: January 13, 2021, 08:45:23 AM »

If you don’t already have some, parts trays are good. I made a few from ply, copying Emmanuel Pariselles. They stack and mean you rarely lose any bits. Also you can keep e.g. all the parts from one reed block together and not mix them up with other parts.

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Hohner Ouveture IV Treble Reed Blocks
« Reply #10 on: January 13, 2021, 03:19:06 PM »

As Theo said same but just a lot more of it.
Logged
Mark Taylor
Folkloristmark
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal