Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3   Go Down

Author Topic: Hohner waxing spoon design  (Read 3770 times)

0 Members and 1 Guest are viewing this topic.

Serge

  • Member
  • *
  • Offline Offline
  • Posts: 21
Hohner waxing spoon design
« on: January 25, 2021, 08:55:23 PM »

Has anyone here had a hands-on experience with the specific design of Hohner type waxing spoon?
I have two conflicting ideas regarding how it functions and it drives me crazy.

Does it have a small nozzle at the bottom front pointy end or does wax run over the top when the spoon is tilted?
I have two pictures that I attach for illustration:
- first is the original Hohner spoon with apparently no nozzle at the front end. I would imagine the wax runs over the top and then down along the front sharp edge.
- second is a Hohner-like spoon and it does have a small nozzle at the front end. Obviously in this case the wax will drip through the nozzle.

I want to replicate the Hohner spoon since the original one is quite costly but I don't understand this thing about the nozzle.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Hohner waxing spoon design
« Reply #1 on: January 25, 2021, 09:19:14 PM »

They’re the same design, it’s just that the first photo doesn’t show the tip very well. It would work in the same manner as the one in the bottom photo.
Logged
C#/D player

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Hohner waxing spoon design
« Reply #2 on: January 25, 2021, 10:00:58 PM »

The wax comes out at the tip, on the pointed part. I have one of these, and find them a bit too bulky. The idea is good, but if I were to make one , it would not be quite so deep, or as long.
Sir John
« Last Edit: January 26, 2021, 09:51:34 AM by John MacKenzie (Cugiok) »
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner waxing spoon design
« Reply #3 on: January 26, 2021, 12:31:55 AM »

The Italian waxing spoons are a shaped flat blade - not hollow with a reservoir. In use, sufficient molten wax clings to the blade.

Available from Charlie Marshall here, or Carini here.
A video from Roger Thomas (of this parish) here, showing how it is used.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Hohner waxing spoon design
« Reply #4 on: January 26, 2021, 01:53:36 AM »

Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner waxing spoon design
« Reply #5 on: January 26, 2021, 06:46:24 AM »

It looks so easy here: https://www.youtube.com/watch?v=yjGaLwqrtOs
Indeed, but in that video, there is plenty of space between the reed plates to allow the reservoir spoon to be used. The problem comes when the space is ca. 1 mm as is often the case between Italian treble end reed plates. The flat blade-type spoon is better for those.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Michael Driscoll

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 145
Re: Hohner waxing spoon design
« Reply #6 on: January 26, 2021, 07:18:23 AM »

It looks so easy here:
That seems to be a further type,used at right angles to the handle, whereas the one in the first picture is  straight. Neither is adjustable, other than by hand movement. You would think a hinge might be useful.
« Last Edit: January 26, 2021, 07:33:56 AM by Michael Driscoll »
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Hohner waxing spoon design
« Reply #7 on: January 26, 2021, 08:34:55 AM »

It looks so easy here: https://www.youtube.com/watch?v=yjGaLwqrtOs
Indeed, but in that video, there is plenty of space between the reed plates to allow the reservoir spoon to be used. The problem comes when the space is ca. 1 mm as is often the case between Italian treble end reed plates. The flat blade-type spoon is better for those.

That same spoon has been used to re-wax hundreds and hundreds of chromatic button accordions with their very tightly spaced reeds, with absolutely no problem at all. It's just a matter of practice and mastering different techniques.
« Last Edit: January 26, 2021, 08:40:40 AM by diatonix »
Logged

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Hohner waxing spoon design
« Reply #8 on: January 26, 2021, 09:57:19 AM »

It looks so easy here: https://www.youtube.com/watch?v=yjGaLwqrtOs
Yes that's the one I use, and by varying how much I load into it, I find I can adapt it, to different situations.

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Michael Driscoll

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 145
Re: Hohner waxing spoon design
« Reply #9 on: January 26, 2021, 10:46:01 AM »

Quote from: John MacKenzie (Cugiok)
[/quote
Yes that's the one I use, and by varying how much I load into it, I find I can adapt it, to different situations.

Where could I get this - I can't see it advertised?

Logged

Prestidigitator

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 448
  • Saltarelle, Hohner, Oakwood Baffetti
Re: Hohner waxing spoon design
« Reply #10 on: January 26, 2021, 11:35:56 AM »

Having seen his videos, I asked Olav Bergflødt (diatonix) about his spoon(s), and he was kind enough to give me some advice on my understanding of the design. I was then able to make several out of copper sheet, in different sizes, with different spouts and with various handle lengths and angles. Used with an electrically-heated wax pot (cosmetics variety), they worked very well, and I had no trouble getting into tight spaces.

I have also used the soldering iron method that Lester Bailey has demonstrated in his videos, as well as the Italian Spoon (home-made from copper sheet and a piece of dowel). I found the soldering iron easy enough, but the Italian Spoon less so, but that was probably because I have least practice in using it. 
Logged

Serge

  • Member
  • *
  • Offline Offline
  • Posts: 21
Re: Hohner waxing spoon design
« Reply #11 on: January 27, 2021, 01:15:14 AM »

...
Used with an electrically-heated wax pot (cosmetics variety), they worked very well, and I had no trouble getting into tight spaces.
...

Tell me more about this please.
I'm also planning on using a Beauty wax heater but mine goes up to 100°C according to the temp control knob dial. As far as I know from an experienced repair person wax should be heated up to approx. 110°C and most consumer grade Beauty wax heaters won't allow it to go up that high.
So how do you use your heater?
Logged

Prestidigitator

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 448
  • Saltarelle, Hohner, Oakwood Baffetti
Re: Hohner waxing spoon design
« Reply #12 on: January 27, 2021, 10:01:02 AM »

...
Used with an electrically-heated wax pot (cosmetics variety), they worked very well, and I had no trouble getting into tight spaces.
...

Tell me more about this please.
I'm also planning on using a Beauty wax heater but mine goes up to 100°C according to the temp control knob dial. As far as I know from an experienced repair person wax should be heated up to approx. 110°C and most consumer grade Beauty wax heaters won't allow it to go up that high.
So how do you use your heater?
The secondhand heater I have is quite an old one, and the dial only has numbers, and not temperatures. I usually turn it to the Max setting, where it melts the wax and keeps it liquid without any problems. I don't do a lot of reed-waxing, but the heater was free, and I decided to put it to this use.

It has an inner metal lift-out "top hat" liner with a detachable handle, and I melt the wax in this. If I want to, I can also melt the hardened wax in the liner in a double-boiler, which, depending on the ambient temperature, is sometimes quicker than melting it from cold in the electric heater.

The only wax I use is of my own making, with beeswax, colophony and oil. I have once tried making it in the heater, but that didn't work well, perhaps because the receptacle isn't big enough for the vigorous stirring needed, and when I have needed more, it's been made in a double-boiler.

Every so often, I melt and dump out any wax that's been left in the heater after perhaps two or three melt/cool cycles, and clean up. Wax seems to lose some qualities if endlessly re-heated, and I try to judge the right amount to melt and use for a couple of sessions. The other thing with using the heater I have and either type of spoon is that it's an advantage, when the wax level is low, to be able to lift up (with the handle) the inner container of melted wax and tip it sufficiently to load the spoon, and then return it.
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: Hohner waxing spoon design
« Reply #13 on: January 27, 2021, 12:53:23 PM »

mine goes up to 100C or 212F. think wax is going to melt around 100 but thats fahrenheit not centigrade. If it gets too hot its going to burn and smoke which is not good.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner waxing spoon design
« Reply #14 on: January 27, 2021, 01:58:38 PM »

 Beeswax melts at around 80-90C, rosin melting point is a bit over 100C.   Accordion wax blend melting at a little below 100C.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner waxing spoon design
« Reply #15 on: January 27, 2021, 02:02:33 PM »

The wax pot you see briefly a couple of times in my demo (see Steve's post above) came from Carini. The inner pot is machined metal and very heavy. It takes about 40 mins to get up to temp. I tried all sorts (gas stove  - dangerous, table heater with old LeCreuset sauce pan...) including a commercial cosmetic wax heater. The one I tried had a switch under the pot, so when you lifted it out the power would cut off. One day some wax got in there and that was the end of that, plus it never really got quite hot enough. In the end I gave in and invested in  (I can’t remember how much but well over €100) the Carini wax pot...and for me it was a complete game changer. All my problems with temperature, smoking wax etc went away. It also has a wire loop to scrape off excess wax from the spoon. I also gave up making the wax and now buy the Italian made stuff.  I have to add though, that for quick jobs Charlie Marshall's wax sticks are really excellent! Somebody gave me some and I’m a real convert.

Serge

  • Member
  • *
  • Offline Offline
  • Posts: 21
Re: Hohner waxing spoon design
« Reply #16 on: January 27, 2021, 04:45:48 PM »

Beeswax melts at around 80-90C, rosin melting point is a bit over 100C.   Accordion wax blend melting at a little below 100C.

Theo, that's right but here is what that repair pro told me:
- "While wax does melt at 100°C it's still not enough for its best temperature point when waxing the reeds. At 100°C wax will flow not as good as it flows at 110° and what's more important at the initial 100°C point the wax will cool down quite fast before it can "firmly grip" the reed plates."
That's of course his personal experience and his personal opinion based on his personal experience. Does it make any sense?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner waxing spoon design
« Reply #17 on: January 27, 2021, 07:10:19 PM »

Serge I completely agree with you.  I was just trying to clarify a previous post that seemed to imply confusion between temperatures C and F.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: Hohner waxing spoon design
« Reply #18 on: January 27, 2021, 09:06:05 PM »

Beeswax melts at around 80-90C, rosin melting point is a bit over 100C.   Accordion wax blend melting at a little below 100C.

ah ok....that kind of explains why maybe those £30 wax pots are a bit rubbish. i tried mine on just over half way on the thermostat and it smoked and discoloured the wax (which i assumed was because it was getting too hot) but sounds like it wasn't getting hot enough or the thermostat or max temp spec. is a bit rubbish. anyway i gave up on it and went back to wax sticks. sounds like you just need need to bite the bullet and get the carini one if you want to go down the pot and spoon road.
Logged

Serge

  • Member
  • *
  • Offline Offline
  • Posts: 21
Re: Hohner waxing spoon design
« Reply #19 on: January 27, 2021, 09:20:15 PM »

Beeswax melts at around 80-90C, rosin melting point is a bit over 100C.   Accordion wax blend melting at a little below 100C.

ah ok....that kind of explains why maybe those £30 wax pots are a bit rubbish. i tried mine on just over half way on the thermostat and it smoked and discoloured the wax (which i assumed was because it was getting too hot) but sounds like it wasn't getting hot enough or the thermostat or max temp spec. is a bit rubbish. anyway i gave up on it and went back to wax sticks. sounds like you just need need to bite the bullet and get the carini one if you want to go down the pot and spoon road.

Another guy involved in the business on the budget once posted this on one of the local boards: "I use a Beauty type wax heater but I removed the thermostat so that the temp goes a little bit higher than 100°C."
It's hard to make any conclusion from his short advice. Perhaps some experimenting with the thermostat part of the circuit can lead to positive results in terms of achieving necessary temperature provided the heater itself has enough capacity to tolerate higher temperatures.

(edit) ... a minute later ...
Wait... I just realized that one of the "traditional" types of waxing pots uses an outer container filled with water and that keeps the wax inside the pot melted.
However - isn't boiling water stays at 100°C temperature point?
Sorry - that all confuses me. I'm really not sure about the best wax temperature and I don't have enough experience to judge it.
Theo and all - can you clarify this once again please?
« Last Edit: January 27, 2021, 09:28:18 PM by Serge »
Logged
Pages: [1] 2 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal