Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reed chamber volume  (Read 1370 times)

0 Members and 1 Guest are viewing this topic.

Gav Wood

  • Good talker
  • **
  • Offline Offline
  • Posts: 99
Reed chamber volume
« on: February 12, 2021, 10:04:21 PM »

If this has been answered before, let me know but i cannot find a suitable answer.

Just about to make a reed block, the block the reeds came from has higher reed chambers with a curved rear wall.
I am assuming this is to minimise volume while still allowing the reed to travel without hitting the back. This is a paolo soprani 50s/60s cba.

See picture below of the block, and tried to show curve at c5 in the drawing.

The curve runs from extreme above c6 to nothing at c4, in a gradual reduction.

So, this obviously took an amount of effort, but does it make that much difference? Will probably copy what is there already, but asking for inspiration - should I aim to keep the same chamber dimensions? The curved back is obviously more work.



Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Reed chamber volume
« Reply #1 on: February 12, 2021, 10:38:15 PM »

I've not come across curved chambers before.
Square chambers are the norm and should be fine for your project.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Reed chamber volume
« Reply #2 on: February 12, 2021, 11:27:10 PM »

The smallest reed chambers often have a small wood wedge to reduce the size of the chamber, tapering away from the opening. When combined with an end-to-end reversal of the reed plate, this is thought to improve the response of the smallest reeds.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Reed chamber volume
« Reply #3 on: February 13, 2021, 01:07:36 AM »

This reminded me of tales of how music hall performers glued cork into the chambers of concertinas to reduce the chamber volume for better sound projection.  Probably quite small returns and only worthwhile in unusual conditions.

Rob.
Logged

Trevor Henderson

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
  • Tender Buttons
Re: Reed chamber volume
« Reply #4 on: February 13, 2021, 01:11:43 AM »

That’s an elegant curve -maybe the builder was imitating the curve of a trumpet bell in his mind. I don’t think the curve would impart an improved tone or response over a straight wedge as Steve mentioned, otherwise it would be common in premier boxes today like Castagnaris.. I once lined a piccolo reed bank in brass (trumpet analogy) and it did nothing to improve things. A wedge in the smaller reed chambers  reduces the air volume and produces  a quicker response. Turning the smallest reeds upside down like Steve mentioned also helps.
 Or maybe the curve is a brilliant and overlooked little tweak that the factory boss scoffed at because it was too time consuming to produce. Hmm  - maybe try it in brass  :||:
Logged

Gav Wood

  • Good talker
  • **
  • Offline Offline
  • Posts: 99
Re: Reed chamber volume
« Reply #5 on: February 13, 2021, 07:24:31 AM »

The box is obviously from one of the big manufacturers, build is typical of this period paolo soprani.
The top reeds are not reversed, maybe it has more effect right at the top than in the middle of the block.
If i build it as normal, it would be very easy to put a similar shaped temporary insert in one or two to test the theory.

The chambers at the top are also significantly narrower, 10.5mm at A6 to 14.5 at a5, part of the same process i suppose.

The small reeds also have narrower shoes, 15.5 instead of 16.5, none look filed, they have the same edges as the larger reeds, the edge looks not cut but guillotined, half smooth half rough.

Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Reed chamber volume
« Reply #6 on: February 13, 2021, 08:29:23 AM »

At least in the highest notes the filled in reed chamber is essential to get the reed to play properly by making sure the frequency of the reed tome is not a fraction of the reed chamber size (my understanding) changing the volume of the chamber affects the volume too, the wood work you see may have something to do with tone balancing.
In the highest notes this can completely prevent the reed from playing if the chamber volume is not reduced.

I have found when I get a Hohner panther and the like in the shop ,that they have just drilled a hole in the block to bleed air and cause turbulence to break up the standing wave. This wastes air and creates a sort of breathy tone to the reed.

I typically have to fill in a bunch of the space behind the reed (and the hole) and this also shifts the reed tone about 10 cents. The reed needs to be tuned after but it speaks better.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Reed chamber volume
« Reply #7 on: February 13, 2021, 08:38:11 AM »

...Turning the smallest reeds upside down like Steve mentioned also helps....
Just to be clear - the reed plates are not turned upside-down; that would cause a push-pull note reversal. The reed plates are simply turned end-for-end, so the rivet end of the reed is nearest furthest from the reed chamber opening.


Edited to correct confusing mistake, as pointed out by Lester.
« Last Edit: February 13, 2021, 02:41:15 PM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Gav Wood

  • Good talker
  • **
  • Offline Offline
  • Posts: 99
Re: Reed chamber volume
« Reply #8 on: February 13, 2021, 09:00:13 AM »

This box was too big to tell if i liked the sound when it was in one piece. Couldnt handle it or push it to get the pressure i would normally play with. Bellows have been stripped and reused now so too late.  I will have a look at the other boxes i like the sound of to see what they do.

Suspect it is the same wood fillet in the top few notes but nothing else.

I like the narrower chamber idea though.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Reed chamber volume
« Reply #9 on: February 13, 2021, 09:08:42 AM »


...Turning the smallest reeds upside down like Steve mentioned also helps....

Just to be clear - the reed plates are not turned upside-down; that would cause a push-pull note reversal. The reed plates are simply turned end-for-end, so the rivet end of the reed is nearest the reed chamber opening.
Just to be even clearer the reed plates are not turned upside-down; that would cause a push-pull note reversal. The reed plates are simply turned end-for-end, so the rivet end of the reed is FURTHEST the reed chamber opening.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Reed chamber volume
« Reply #10 on: February 13, 2021, 09:21:43 AM »


...Turning the smallest reeds upside down like Steve mentioned also helps....

Just to be clear - the reed plates are not turned upside-down; that would cause a push-pull note reversal. The reed plates are simply turned end-for-end, so the rivet end of the reed is nearest furthest from the reed chamber opening.
Just to be even clearer the reed plates are not turned upside-down; that would cause a push-pull note reversal. The reed plates are simply turned end-for-end, so the rivet end of the reed is FURTHEST the reed chamber opening.
Doh! :|bl
Yes - my mistake, sorry! Lester is correct, as usual.

I knew that really but I often confuse directional things. I have trouble saying the correct words for left and right, even though I know the difference between left and right. I guess it's a sort of directional dyslexia.

Funny though - I never have any difficulties distinguishing up from down.  ;)
« Last Edit: February 13, 2021, 02:41:49 PM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Gav Wood

  • Good talker
  • **
  • Offline Offline
  • Posts: 99
Re: Reed chamber volume
« Reply #11 on: February 13, 2021, 09:52:56 AM »

I understood what you meant about upside down, depends on your viewpoint. These reeds are at present unisonoric so would not change the pitch by flipping them. Ha ha.

Anyway, checked some other boxes, couple of paolo  from a different manufacturer, my favourite - busillachio and scandalli.
The super scandalli is the only one with wedges, but these are very high- a6 and above, and reeds flipped end to end d7 and above. My diatonic will not be going that high.


Logged

Trevor Henderson

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
  • Tender Buttons
Re: Reed chamber volume
« Reply #12 on: February 13, 2021, 01:28:40 PM »

...Turning the smallest reeds upside down like Steve mentioned also helps....
Just to be clear - the reed plates are not turned upside-down; that would cause a push-pull note reversal. The reed plates are simply turned end-for-end, so the rivet end of the reed is nearest the reed chamber opening.
In my colonial usage of English the push-pull reversal would be ‘inside out’  (:)
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal