Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: sluggish bass reed action  (Read 2128 times)

0 Members and 1 Guest are viewing this topic.

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
sluggish bass reed action
« on: February 13, 2021, 02:39:33 PM »

I've taken apart an old Hohner Club and revalved the bass side.
The reed producing the c3 note however won't speak, or with heavy delay.
I've taken the reed plate out of the reed block and reversed it so I have access to the reed itself.
I've experimented with a wider and narrower gap, testing it on my tuning table, but there's no improvement.
There's hardly any tuning damage. The reed is a Hohner T reed on a zinc plate.
I guess I've checked the relevant parameters: reed straightness (compared it with reeds from another properly functioning club), gap at the top, fit in the plate gap... Also I don't believe any air is leaking due to a warped bottom plate of the reed block.

Would it help if I took away some material at the base of the reed and from the copper bulge at the tip of the reed?
I would guess the reed would be less stiff and better responding.
any advice welcome.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: sluggish bass reed action
« Reply #1 on: February 13, 2021, 02:47:07 PM »

Either of those changes will change the pitch of the reed.

Have you tried the reed in it’s normal position inside the instrument?  Hohner bass needs use a lot of air and it can be difficult to get sufficient air if you use a tuning table.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: sluggish bass reed action
« Reply #2 on: February 13, 2021, 02:47:37 PM »

Have you checked that the valve is operating correctly?
The valve could be glued down too much, or stuck somewhere else. A stray bit of wax or dirt can cause the valve not to open properly, or if it is an inside valve, it could be catching on the side or end of the reed chamber.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: sluggish bass reed action
« Reply #3 on: February 13, 2021, 03:04:32 PM »

Tuning bass reeds doesn't work on a standard tuning table.
I have one made for the job with bigger bellows and a bigger air hole.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: sluggish bass reed action
« Reply #4 on: February 14, 2021, 10:48:26 AM »

Hi everyone, thanks for sharing your thoughts on this.
Theo, the idea was that if I lower and raise the pitch at the same time by grinding a bit of both tip and base, I'll end up having the same pitch but with a more supple and responsive reed.
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: sluggish bass reed action
« Reply #5 on: February 14, 2021, 10:57:48 AM »

the idea was that if I lower and raise the pitch at the same time by grinding a bit of both tip and base, I'll end up having the same pitch but with a more supple and responsive reed.

Don't do that. It will do more harm than good. And remember to check the alignment of the reed, without valve and against the light. This will also make it easier to see whether something else is obstructing free movement of the reed.
« Last Edit: February 14, 2021, 11:36:57 AM by diatonix »
Logged

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: sluggish bass reed action
« Reply #6 on: February 15, 2021, 09:07:37 AM »

Hi diatonix,

Thanks for the tip. The reed was misaligned a bit, but it being fixed by two rivets I see no way of adjusting its position.
Instead I filed away some of the side of the reed. Response is better, but still so-so.
Logged

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: sluggish bass reed action
« Reply #7 on: February 15, 2021, 09:30:57 AM »

If I have a large, slow sounder, I tend to turn the reed around as a "first test", so the bellows table direction is reversed for testing.  Pretty much invariably the 'slow' reed is on the "drop", ie pulling the air from the open atmosphere as opposed to the 'push' - pushing the tuning air through the compression of the reed chamber.

When the air is compressed through the reduced space of  the chamber it usually sounds, in terms of speed / effort 'as would be expected' - albeit the pitch can't be managed/tuned as such by that means because that is not how it operates when it is the right way around.

So, I come down to - as others have said having a bigger tuning hole on my 'desk', for tuning bass reeds and trying to find that point in the flow where it is best to tune the bigger reeds to.  I nearly always find they start slow (flat) / and go the other way (sharp) through the range of the bellows operation as the reed speeds up, which makes it a real wing and a prayer/suck it and see job to fine fettle them, the bigger they are.

I would turn it around on the block ( assuming you are "dry" working at this stage ) and see if it is better on the 'tuning' push.

Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: sluggish bass reed action
« Reply #8 on: February 15, 2021, 10:39:39 AM »

...So, I come down to - as others have said having a bigger tuning hole on my 'desk', for tuning bass reeds...
The 'tuning hole' on my tuning table is large enough to place the entire instrument end over it, so I can sound and tune the reeds in situ. This makes for far more accurate tuning than having the reed blocks out of the instrument with the reeds being sounded by placing each chamber over a small cut-out hole.

My tuning bellows are about the size of a Castagnari Mory or Handry, so the effective air volume employed for sounding the reeds is very close to the instrument's own bellows. This really helps when working on those large bass reeds.

For working on smaller instruments, I use a thin plywood strip covered with chamois which I can clamp and and butt up to the instrument end, or else have thin plywood 'masks' with different size cut-outs which I can clamp to the tuning bellows top.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: sluggish bass reed action
« Reply #9 on: February 16, 2021, 09:29:18 AM »


The 'tuning hole' on my tuning table is large enough to place the entire instrument end over it, so I can sound and tune the reeds in situ. This makes for far more accurate tuning than having the reed blocks out of the instrument with the reeds being sounded by placing each chamber over a small cut-out hole.


Exactly. That's how it's done. Not only because it makes for more accurate (and faster) tuning, but also because I have the whole keyboard at my disposition which allows me to easily compare intervals, rate of tremolo etc. This is very important.
« Last Edit: February 16, 2021, 11:59:00 AM by diatonix »
Logged

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: sluggish bass reed action
« Reply #10 on: February 16, 2021, 10:03:10 PM »

Thanks all for sharing tips!

As for me using a tuning table: For the bass reed I used the tuning table because it gives a clear view of the reed in action (I switched the plate because it was an inside-reed)
The Hohner bass reed block has a double opening, which fits over the two holes I made for tremolo tuning.

I have recently started tuning reeds inside the instrument. I fix either top or bottom part to a chair, tape off the pin holes, and sound the note I tune playing the instrument. The downside is endlessly assembling and taking apart the instrument resulting in back pains, but it saves me the trouble of making tuning charts and having to constantly use them as reference, and the results seem better.

Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: sluggish bass reed action
« Reply #11 on: February 17, 2021, 05:38:04 AM »

The downside is endlessly assembling and taking apart the instrument

One of the first things every melodeon tuner in spe must learn is how to effortlessly access most reeds without taking the blocks out of the instrument.
« Last Edit: February 17, 2021, 06:40:32 AM by diatonix »
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: sluggish bass reed action
« Reply #12 on: February 17, 2021, 07:42:27 AM »


I have recently started tuning reeds inside the instrument. I fix either top or bottom part to a chair, tape off the pin holes, and sound the note I tune playing the instrument. The downside is endlessly assembling and taking apart the instrument resulting in back pains...

You don't need to do this. Make a suspension frame from 9mm plywood:

1. Make it 'U' shaped, except make the shape with a straight base to the 'U', not rounded. So it is like three sides of a rectangle.
2. Make the arms 10 cm wide and the base of the 'U' a bit wider, say 15 cm.
3. The space between the arms must be just slightly smaller (about 1.5 to 2 cm) than the external bellows dimension.
4. Round the edges of the arms with sandpaper so they are smooth.
5. Clamp the base of the frame to the edge of a bench or table with the arms projecting over the edge.

6. Remove the bellows pins from the instrument end you are working on and separate the end from the bellows.
7. Gently insert the rest of the instrument, sliding the top fold of the bellows into the plywood frame. The instrument can then be suspended from the frame by its bellows.
8. Fit the instrument end you are working on back on to the bellows frame but do not replace the pins.
9. You can now sound the reeds by lifting the other end up and down on its suspension frame.
10. It's now quick and easy to lift the end off the frame to work on the reeds until the pitch is correct.

This method is good for small, light instruments, but for larger, heavier instruments, it is better to make a tuning table with a large cut-out opening as shown in my previous photos.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: sluggish bass reed action
« Reply #13 on: February 17, 2021, 10:14:22 AM »

Diatonix, I leave the blocks in the instrument. I use a hook to access the inner reeds, which works pretty well.

Steve, that's an interesting solution. But don't the bellows suffer from the suspension frame at all?
The Hohner Club III M I'm currently working on might be a bit too heavy for this particular solution?
I'll give it a go on my prewar Club II, since that's a pretty light box.
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: sluggish bass reed action
« Reply #14 on: February 17, 2021, 10:49:24 AM »

I use Steve's method which was shown to us by Emmanuel Pariselle (I think Theo does too).
It works very well for me making tuning "in the box" quick and easy.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: sluggish bass reed action
« Reply #15 on: February 17, 2021, 10:53:24 AM »

Steve, that's an interesting solution. But don't the bellows suffer from the suspension frame at all?
I worried about that at first, but actually the bellows come to no harm using this method. Just ensure that your suspension frame arms are sanded nice and smooth.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: sluggish bass reed action
« Reply #16 on: February 17, 2021, 11:12:17 AM »

I use Steve's method which was shown to us by Emmanuel Pariselle (I think Theo does too).
It works very well for me making tuning "in the box" quick and easy.


And me

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: sluggish bass reed action
« Reply #17 on: February 17, 2021, 11:59:16 AM »

Yes I use this method. To protect the bellows I have the edges rounded and lined with gaffa tape.

 I have a tuning table too, but I only use that for pre-tuning - checking that reeds are close to the correct pitch before valving and mounting on blocks.  It’s also handy for a quick check of a freshly waxed block to ensure I’ve not got reed in the wrong place.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: sluggish bass reed action
« Reply #18 on: February 17, 2021, 08:44:10 PM »

Hi Steve, I made your contraption and it works great!
Logged

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: sluggish bass reed action
« Reply #19 on: February 17, 2021, 08:48:52 PM »

By the way as you can see this is really a crap scrap club.
Great for my learning curve though, and I might turn it into a playable instrument.
I decided to first try and get the bass side playing properly. If that doesn't work I can save myself the trouble of re-padding the pallets on the treble side, de-rusting all treble reeds, revalving, waxing and tuning, ánd retaping the bellows
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal