Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: 1 row 4 stop pallet question  (Read 1624 times)

0 Members and 2 Guests are viewing this topic.

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
1 row 4 stop pallet question
« on: February 18, 2021, 06:51:16 PM »

I'd be really interested and grateful for some measurements of pallet lift on decent 1 rows if anyone is able or has some figures to hand.  ie clearance of each end of the pallet (which are obviously significantly different because of the angle) above the fondo at full button depression - especially clearance over the hole for the L reeds.

Daydreaming ahead to a potential project . . . . . (:)

Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: 1 row 4 stop pallet question
« Reply #1 on: February 18, 2021, 08:03:49 PM »

My beltuna has about 3/8” so 9.5mm? Basically on the front it rises to the height of the pallet top.
Not sure how much exactly on the back edge of pallet but about 4mm, not much.
On my recent one row build I got the clearance to be more thinking it would be better for air flow, in hindsight I’d go less.

Edit to add:  my build ended up with 5/8” on the front and a good 1/4” on the back
« Last Edit: February 18, 2021, 08:08:33 PM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: 1 row 4 stop pallet question
« Reply #2 on: February 18, 2021, 08:12:04 PM »

I checked a few boxes and it's around 12 to 15 mm with button flush with keyboard face, increases to 17-18 mm max with button all the way down.  About 10 mm (with button flush) for L reed, i.e. center of 2nd hole from front.
« Last Edit: April 13, 2021, 03:45:18 PM by tirpous »
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: 1 row 4 stop pallet question
« Reply #3 on: February 18, 2021, 08:24:18 PM »

Hohners have the L reed at the back which has the lowest pallet lift.
Cajun style boxes, as tirpous says, the L reed is 2nd hole from front so higher pallet lift.

My Windjammers have the Hohner system while Clipper and Corvette are laid out Cajun style.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: 1 row 4 stop pallet question
« Reply #4 on: February 18, 2021, 10:57:06 PM »

Brilliant, thanks all. I think that's probably answered my concern. 
I'm thinking my way towards making another one row, and pondering what I might do differently to the first one. Currently my pallets have pretty much exactly the lift of Boxcall's Beltuna and I'm reluctant to increase that as I'm very happy with feel of the action, but very occasionally and only when all 4 voices are sounding I feel the lowest of the L reeds are perhaps being a little starved. Given that it's laid out like a Hohner the obvious thing is to change that and position the L reeds further out where there is more lift and hence airflow . . . . Other thoughts welcome though ;)

Logged

Trevor Henderson

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
  • Tender Buttons
Re: 1 row 4 stop pallet question
« Reply #5 on: February 18, 2021, 11:20:58 PM »

the obvious thing is to change that and position the L reeds further out where there is more lift and hence airflow . . . . Other thoughts welcome though ;)


I built mine with the the reed banks in this order MMLH - with the H bank being furthest from the keyboard. This gives the L bank plenty of air. The first M and the H banks are laid flat.
Logged

Stephen

  • Member
  • *
  • Offline Offline
  • Posts: 5
Re: 1 row 4 stop pallet question
« Reply #6 on: February 18, 2021, 11:27:53 PM »

Would placing the H reeds in the location with lowest pallet lift be a good option? I often thought the M bank of reeds closest to the keyboard on my MMLH melodeon could do with a bit more lift.
Logged

Trevor Henderson

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
  • Tender Buttons
Re: 1 row 4 stop pallet question
« Reply #7 on: February 18, 2021, 11:40:13 PM »

I find that the first M bank on my seems balanced - probably because it’s laying flat and gets a little volume boost from that.
Logged

Trevor Henderson

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
  • Tender Buttons
Re: 1 row 4 stop pallet question
« Reply #8 on: February 18, 2021, 11:43:22 PM »

But I see your point about Switching it with the H. However if you play any Cajun you probably want a strong H row
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: 1 row 4 stop pallet question
« Reply #9 on: February 19, 2021, 12:00:30 AM »

I find that the first M bank on my seems balanced - probably because it’s laying flat and gets a little volume boost from that.
I would say laying flat helps volume and it may help even more when and if this bank is tuned M+.


Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: 1 row 4 stop pallet question
« Reply #10 on: February 19, 2021, 03:54:38 AM »

M+MLH arrangement (moving away from the keyboard) is the standard arrangement for 4-stops with the exception of Hohners.  With the MM reeds, when they are very close (or even directly next to) the keyboard, it helps to have a small channel carved out in the fondo between the two holes - this allows the sound to make its way out a little better.  I've done this on one of my boxes and it makes a difference.

Logged
C#/D player

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 1 row 4 stop pallet question
« Reply #11 on: February 19, 2021, 07:19:27 AM »

... With the MM reeds, when they are very close (or even directly next to) the keyboard, it helps to have a small channel carved out in the fondo between the two holes - this allows the sound to make its way out a little better.  I've done this on one of my boxes and it makes a difference.

Presumably on the outside of the fondo underneath the pallet?
Does it affect the sound if you switch out the M+ voice, i.e. to play in unison octaves: LMH?
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: 1 row 4 stop pallet question
« Reply #12 on: February 19, 2021, 11:02:32 AM »

Presumably on the outside of the fondo underneath the pallet?
Does it affect the sound if you switch out the M+ voice, i.e. to play in unison octaves: LMH?
Thinking about it, I've seen a photo (I don't recall where) of this. As you surmise, just a simple shallow channel under the pallet and linking the two holes.

My box has upright blocks, and as a first instrument I went broadly with Hohner based layout and dimensions simply as a known starting point rather than entirely re-invent the wheel.
I also liked the sound of the Castagnari with upright blocks, and I wasn't looking to make  a Cajun style box.
However - MMLH certainly makes more sense to me, and I hadn't appreciated that Hohner were apparently totally on their own in not doing that!
I guess the first step is to make new reed blocks for my existing box to give a direct comparison of the altered postions with everything else unchanged, and then decide from there . .
Logged

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: 1 row 4 stop pallet question
« Reply #13 on: February 19, 2021, 06:43:31 PM »

Well, it proved straightforward to simply re-arrange the existing reed blocks without anything clashing, which has certainly made a difference.  So a result for now albeit it with a slightly oddball M+HLM, and confirms that MMLH is the way to go next time.
Logged

Trevor Henderson

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
  • Tender Buttons
Re: 1 row 4 stop pallet question
« Reply #14 on: February 19, 2021, 07:06:37 PM »

Unless you’ve accidentally discovered the new gold standard with M+HLM
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: 1 row 4 stop pallet question
« Reply #15 on: February 19, 2021, 08:06:40 PM »

Quote
Unless you’ve accidentally discovered the new gold standard with M+HLM

Maybe for an all-reeds-standing design.  For a flat-standing-standing-flat layout to fit within the standard frame (and bellows) width, it's almost mandatory to have the shorter H reeds mounted flat.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: 1 row 4 stop pallet question
« Reply #16 on: February 19, 2021, 08:30:56 PM »

Quote
Unless you’ve accidentally discovered the new gold standard with M+HLM

Maybe for an all-reeds-standing design.  For a flat-standing-standing-flat layout to fit within the standard frame (and bellows) width, it's almost mandatory to have the shorter H reeds mounted flat.
Yes, no room to spare. Even with MMLH on my Bb box I had to remove material along both sides of casework to make room for the reeds. This is with the standing block and flat blocks being as tight as possible with just enough room for reeds to fit.

Edit to add: on my fondo I have squared holes and did not need to carve out any wood to gain more air to the back M or M+ reeds, plenty of volume.
« Last Edit: February 19, 2021, 08:33:56 PM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: 1 row 4 stop pallet question
« Reply #17 on: February 20, 2021, 04:25:37 AM »

... With the MM reeds, when they are very close (or even directly next to) the keyboard, it helps to have a small channel carved out in the fondo between the two holes - this allows the sound to make its way out a little better.  I've done this on one of my boxes and it makes a difference.

Presumably on the outside of the fondo underneath the pallet?
Does it affect the sound if you switch out the M+ voice, i.e. to play in unison octaves: LMH?

Outside of the fondo and underneath the pallet, yes, but it's only partially carved out of the wood - it's not a hole that goes all the way through so it doesn't affect the functioning of the individual reedbanks.  I've attached a photo that illustrates how I did this with a box of mine to allow for better sound travel/volume from that inner row of holes.  It really did make a difference!  My Mélodie 4-stop has the same thing, which is what gave me the idea.
Logged
C#/D player

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: 1 row 4 stop pallet question
« Reply #18 on: February 20, 2021, 07:39:42 AM »

Outside of the fondo and underneath the pallet, yes, but it's only partially carved out of the wood - it's not a hole that goes all the way through so it doesn't affect the functioning of the individual reedbanks.  I've attached a photo that illustrates how I did this with a box of mine to allow for better sound travel/volume from that inner row of holes.  It really did make a difference!  My Mélodie 4-stop has the same thing, which is what gave me the idea.

Good photo and explanation, thanks!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: 1 row 4 stop pallet question
« Reply #19 on: February 20, 2021, 04:06:12 PM »

... With the MM reeds, when they are very close (or even directly next to) the keyboard, it helps to have a small channel carved out in the fondo between the two holes - this allows the sound to make its way out a little better.  I've done this on one of my boxes and it makes a difference.

Presumably on the outside of the fondo underneath the pallet?
Does it affect the sound if you switch out the M+ voice, i.e. to play in unison octaves: LMH?

Outside of the fondo and underneath the pallet, yes, but it's only partially carved out of the wood - it's not a hole that goes all the way through so it doesn't affect the functioning of the individual reedbanks.  I've attached a photo that illustrates how I did this with a box of mine to allow for better sound travel/volume from that inner row of holes.  It really did make a difference!  My Mélodie 4-stop has the same thing, which is what gave me the idea.

This method probably gives the reed a bit of a head start taking air ( even if a millisecond )as well the better sound/ volume.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal