Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3   Go Down

Author Topic: Microphones and amplification  (Read 15171 times)

0 Members and 1 Guest are viewing this topic.

Morrisbox

  • Good talker
  • **
  • Offline Offline
  • Posts: 85
Re: Microphones and amplification
« Reply #20 on: October 16, 2009, 08:48:51 PM »

Quote
And of course, Lester, with the velcro change, someone has to be ready to turn down both channels on the mixer or you have to remember to turn down the preamp controls, and then up again afterwards, to avoid the audience being subjected to hugely amplified ripping noises, which could easily be confused with something else!
Quote
Easier to have a "reminder twiddle" for the next tune without having to pull a cable out
No longer forgetting to plug back in after said  "reminder twiddle"

Like Lester I use Microvox, but to get over the issue of change over, and indeed "reminder twiddle" I use a 2-way selector pedal (AB-2) foot switch, plug the Microvox into one input socket, and leave the other "empty" and just switch to the "empty" line when changing or "twiddling".  Mine has a helpful red light to show when the melodeon is "live",  I find this helps a lot.

Trevor
Logged

ganderbox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 734
  • Melodeons from Brittany, Italy, Germany* and Leeds
    • www.choughedtobits.co.uk
Re: Microphones and amplification
« Reply #21 on: October 17, 2009, 10:55:07 AM »

I use a unidirectional condenser mike on a stand for the treble end, and a microvox for the bass. I tried a microvox on the treble end, but it didn't sound as good as the microphone.
As I always sit down for gigs, I can get away with using a short mikestand (designed for a bass drum, I think), which is neater than some of fullsized stands.
Feedback can be a problem sometimes, but as long as I make sure the mike is properly positioned it's OK.
I only use one instrument for gigs at the moment, so swapping over the microvox on the bass isn't an issue, but if I do start using two I will probably get a foot-pedal. 
Logged
Pauline from Cornwall

*  including a customised Hohner Club from Cornwall (and very nice it is too!).

vielleuse

  • Member
  • *
  • Offline Offline
  • Posts: 14
Re: Microphones and amplification
« Reply #22 on: October 17, 2009, 11:21:31 AM »

I periodically pop up and post on these threads when I decide I Really Must Do Something about amplifying my instrument, get a lot of confusing replies, decide it's all too expensive and give up, but anyway...

Tim Van Eyken has (or had last year when I asked him about it) an interesting system. Two Audio Technica Pro-35 x mikes: the right hand one is just clipped to the grill, and the left hand one is mounted on a velcro wristband. So no drilling or glueing anything permanently onto the instrument at all, and because the left hand one is attached to the hand and not the instrument, it's very quick to change instruments. Unfortunately these mikes are now discontinued, but they are miniature cardioid mikes (I have a vague idea what that means).

I REALLY DO need to sort out the amplification issue for myself though as I've started gigging fairly regularly with the box in fairly low rent venues where there is no guarantee that there will be enough mikes for the whole band and am really tempted by this as it's an all-in-one solution with full gain/balance and EQ adjustment, no need to buy extra bits, not that expensive considering, and I'm very happy with the KK pick-up system I have for the hurdy-gurdy: http://www.kksound.com/accordion.html

I might be inclined to try and go for the left hand wristband option rather than sticking the mike at the bottom like that though. There is also an option to have a 2 mike system (one for each side) ... possibly that might be better if there's an interference issue from having 2 on one side on a shorter instrument (and of course it's cheaper).
« Last Edit: October 17, 2009, 11:39:39 AM by vielleuse »
Logged

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Microphones and amplification
« Reply #23 on: October 17, 2009, 02:21:26 PM »

Saul Rose has a similar system to what you describe vielleuse. I use the microvox thing and I'm reasonably happy with it. It works fairly well, the sound isn't stunning, but adequate and it's easy to set up.

Spiers when I saw him at Sidmouth seemed to have a magnetic pickup attached to the front face of the treble side of his box, which was interesting. Not so much of a problem switching, but involved a great magnetic sticker thing on the front.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Microphones and amplification
« Reply #24 on: October 18, 2009, 05:18:59 PM »

If your changing boxes you (or your sound man) needs to be in control of things anyway, what with the change in volumes/tones. What might be a great setup for a Pokerwork (treble cut!!) might sound a bit muddy on a 3v Castagnari which is far darker in sound straight away.

Which is why a stand mic for the treble end is a better idea, you can move closer and further away depending on which box you're playing. I set up so my D/G Oakwood (D/G, MM reeds) is about 18" away, my Castagnari Dony (D/G/acc, LM reeds) about 12" away, my Tommy (G/C, LMM reeds) about 9" away -- this equalises the volumes out front and in the foldback without this having to be done from the desk.

And they're all far enough away to get even pickup, with no multiple-mic comb interference -- which is often obvious and quite nasty if you're the poor sod responsible for the out-front sound, even if the box player doesn't notice it.

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

ladydetemps

  • Emote Wizard
  • Forum Librarian
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 3768
  • Castagnari Tommy D/G, Hohner 1 row 4 stop in C
    • My Youtube Channel
Re: Microphones and amplification
« Reply #25 on: October 18, 2009, 05:22:49 PM »

Question: whats the difference between condenser and dynamic. And what is phantom power?

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Microphones and amplification
« Reply #26 on: October 18, 2009, 05:34:08 PM »

Question: whats the difference between condenser and dynamic. And what is phantom power?

Dynamic mics are like a speaker in reverse -- little coil of wire attached to a diaphragm.

Condenser mics use a charged diaphragm which needs an internal amplifier which needs a power source. This can come from a battery, or be sent down the cable from the mixer which is phantom powering. Since some things don't having this done to them, it's best if the mixer can turn phantom power on and off for each channel individually. Some cheap mixers don't haver phantom power at all, some only have a switch for all channels, higher-quality mixers usually have individual switches.

Condenser mics are (generally speaking) less robust but have a more accurate sound, are less prone to handling noise, and are better for micing instruments like acoustic guitar or orchestral stuff.

Dynamic mics are more robust and idiot-proof, are often preferred for close-micing vocals, and are absolutely fine for squeezeboxes (as are condenser mics).

What is more important is to have a good quality mic, correctly positioned. One with a hypercardioid pickup pattern may be better if you're playing in noisy conditions, these reject noise from the sides and rear of the mic better than a cardioid mic -- don't use an omnidirectional mic, these pick up sound from all directions equally which is the last thing you usually want.

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Bill Young

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1151
  • Paolo Soprani BCC#
Re: Microphones and amplification
« Reply #27 on: October 18, 2009, 05:41:32 PM »

Question: whats the difference between condenser and dynamic. And what is phantom power?
There's some useful information here. Also Basic Microphones, and other books in the Basic series about sound, are worth looking at.
Logged

ladydetemps

  • Emote Wizard
  • Forum Librarian
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 3768
  • Castagnari Tommy D/G, Hohner 1 row 4 stop in C
    • My Youtube Channel
Re: Microphones and amplification
« Reply #28 on: October 18, 2009, 05:59:46 PM »

Being an idiot, hmm maybe I should go for idiot proof one.

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Microphones and amplification
« Reply #29 on: October 18, 2009, 06:13:54 PM »

Paul White is a really good writer regarding sound recording - all of his advice is sound (no pun indented) and he doesn't bamboozle with jargon. I would recommend any of his writing in Sound on Sound or his books.
Logged

Falseknight

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 449
    • False Knight
Re: Microphones and amplification
« Reply #30 on: October 18, 2009, 11:07:43 PM »

A true clod can make scrap from any microphone.  Condenser microphones make more expensive scrap.

In general, phantom powered condensers are smaller, lighter and have a wider frequency response than dynamic microphones - which is why you see professional players with small capsule condenser mics mounted on wrist straps etc.

If I remember rightly, the Microvox system is an omni-directional condenser system (an array of 4? mics on the treble side).  This works fine if you are close to a high volume sound source.  I was recommended them for mandolin in the late 80s but found them horribly feedback prone - for obvious reasons.
« Last Edit: October 18, 2009, 11:14:13 PM by Falseknight »
Logged

vielleuse

  • Member
  • *
  • Offline Offline
  • Posts: 14
Re: Microphones and amplification
« Reply #31 on: October 20, 2009, 12:04:54 AM »

I've been corresponding with K&K about the accordion system I posted earlier. It seems they will do a version which has only two mikes, one for each side, which might work better on my little Castagnari Benny if there's a potential interference problem (the spec says they have to be 10-12" apart, and the Benny isn't even 10" high). Plus it makes it cheaper. The microphones it uses are these: http://www.kksound.com/silverbullet.html

I might well ask them to throw in some of the clips that the silver bullet mike comes with so that I can try out wrist straps and the like instead of/as well as the velcro option.

What really appeals is the little pre-amp. What I did for the hurdy-gurdy was sit down with a screwdriver and a PA and fiddle around with the EQ till I got a sound I liked. You then have a sound to give the engineer which is at least in the right ballpark, and is just a single input. You can't, and wouldn't want to, adjust the EQ yourself on stage, but you have got separate volume controls for each side.
Logged

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Microphones and amplification
« Reply #32 on: October 20, 2009, 09:48:10 PM »

I've been corresponding with K&K about the accordion system I posted earlier. It seems they will do a version which has only two mikes, one for each side, which might work better on my little Castagnari Benny if there's a potential interference problem (the spec says they have to be 10-12" apart, and the Benny isn't even 10" high). Plus it makes it cheaper. The microphones it uses are these: http://www.kksound.com/silverbullet.html

I might well ask them to throw in some of the clips that the silver bullet mike comes with so that I can try out wrist straps and the like instead of/as well as the velcro option.

What really appeals is the little pre-amp. What I did for the hurdy-gurdy was sit down with a screwdriver and a PA and fiddle around with the EQ till I got a sound I liked. You then have a sound to give the engineer which is at least in the right ballpark, and is just a single input. You can't, and wouldn't want to, adjust the EQ yourself on stage, but you have got separate volume controls for each side.

Just a couple of comments -- the "soft cardioid" pattern has pretty poor rejection of sounds from the sides/rear which will make it more prone to picking up ambient noise and feedback, and it looks like a single treble end mic won't be far enough away to get even pickup -- and if it is, it will be even more feedback prone.

Speaking with my sound engineer hat on, the *last* thing I want with a squeezebox is a single input with combined bass and treble -- you're stuck with the balance and combined EQ the player has set (possibly for the sound they want in the monitors or headphones, which is not usually what you want for FOH), you can't EQ the two ends separately, if you turn up the gain for a solo or a quiet bit and the bass end starts to feed back (it's usually the bass end) you can't do anything except turn the whole thing down, you can't vary the levels of the two ends separately to deal with changes in playing level (at higher volumes you don't usually want the bass end to come up in level as much as the treble end), if they swap instruments the balance is rarely the same -- I'm sure I could think of more problems if I really tried... :-)

And for a "non-professional" solution with a lot of disadvantages, it's pretty damned expensive...

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Chris Brimley

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2038
Re: Microphones and amplification
« Reply #33 on: October 20, 2009, 11:09:27 PM »

Looking at the photo, and looking at the many expert comments from sound engineers on this thread, it would seem to me doubtful that the K&K system would perform succesfully on a box.  Please someone correct me if I've got this wrong, but I would have thought this sort of mike only works without severe feedback problems if the mike is very close (of the order of 2-3cm) to the sound source, and you couldn't do that with a box and just one RH mike, and get an even input from all the RH reeds.  Looking at the picture, it is so close to the flute's mouthpiece it's virtually sticking up the player's nose, and it would be really difficult to avoid amplifying unwanted breath and mouth noises.  What's more, isn't it so close that it is going to alter the sound characteristics significantly (like the effect you get if you put your ear very close to a cymbal, where the bass suddenly overwhelms the sound)?
Logged

vielleuse

  • Member
  • *
  • Offline Offline
  • Posts: 14
Re: Microphones and amplification
« Reply #34 on: October 20, 2009, 11:51:58 PM »


Just a couple of comments -- the "soft cardioid" pattern has pretty poor rejection of sounds from the sides/rear which will make it more prone to picking up ambient noise and feedback, and it looks like a single treble end mic won't be far enough away to get even pickup -- and if it is, it will be even more feedback prone.

Speaking with my sound engineer hat on, the *last* thing I want with a squeezebox is a single input with combined bass and treble -- you're stuck with the balance and combined EQ the player has set (possibly for the sound they want in the monitors or headphones, which is not usually what you want for FOH), you can't EQ the two ends separately, if you turn up the gain for a solo or a quiet bit and the bass end starts to feed back (it's usually the bass end) you can't do anything except turn the whole thing down, you can't vary the levels of the two ends separately to deal with changes in playing level (at higher volumes you don't usually want the bass end to come up in level as much as the treble end), if they swap instruments the balance is rarely the same -- I'm sure I could think of more problems if I really tried... :-)

And for a "non-professional" solution with a lot of disadvantages, it's pretty damned expensive...

Ian


Perhaps you can suggest a better solution. Because this is what always happens. I get overwhelmed with information, anything I think of buying always ends up seeming like a bad idea, and I end up buying nothing, and having to perform through two stand mikes with wholly inadequate results.

Incidentally, the right hand grill on a Benny is less than 8" long. That doesn't seem like a long distance to pick sound up over. I've been working on the assumption that that probably made it too short to have two mikes on that side without interference. It really is very short.
« Last Edit: October 21, 2009, 12:18:08 AM by vielleuse »
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Microphones and amplification
« Reply #35 on: October 21, 2009, 09:10:43 AM »

I agree that separate outputs are needed for treble and bass.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Chris Brimley

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2038
Re: Microphones and amplification
« Reply #36 on: October 21, 2009, 10:26:25 AM »

Quote
Perhaps you can suggest a better solution. Because this is what always happens. I get overwhelmed with information, anything I think of buying always ends up seeming like a bad idea, and I end up buying nothing, and having to perform through two stand mikes with wholly inadequate results.

I have much sympathy with you, vielleuse, as I'm no sound engineer either.  Isn't the root of the problem that there isn't yet a really good answer available for miking boxes, and we're all compromising, without there being a consensus?

I looked at the pdf 'technical' document that you can read about the K&K system, and it seems to me anyone buying one can't tell in advance how much drop in signal you would get between a reed 2/3cm away from the mike, and one at the end of the keyboard (perhaps about 10/11cm away on your box?)  There's a polar diagram, but in the absence of a scale, and having only one pattern, you can't even estimate what the drop-off will be.  But from the response from the back of the mike, it certainly looks as if feedback could also be a problem, as IanD has pointed out. 

Ian, can you help us at all?

(Erm, this may be heresy, but do close miking systems for boxes actually work properly yet?  The more I understand about their inherent problems, the more I'm reaching the conclusion that they have some way to go.)

Logged

jb

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 250
Re: Microphones and amplification
« Reply #37 on: October 21, 2009, 10:28:53 AM »

I agree that separate outputs are needed for treble and bass.

I agree too. But then the key question is who is responsible for the mix out front, and what does this imply for the kind of setup you want/need.
If you could rely on there always being a sound engineer out front who knew what sound you wanted/needed, and if you were playing primarily through a PA rather than backline, then I guess you would want to send the two channels separately out to the desk. And then you need to figure out what is your favourite affordable set up to achieve this, e.g. two standing mics, two clip-ons with separate pre-amps etc, or a combination of the two.
But for many of us these are pretty big ifs. In most settings I play principally through a backline amp and from there (if necessary) into PA, the latter mixed by me or another band member who has to make their own guesstimate about how its all sounding out front. So given this I'm happy to go with the convenience of a set-up described earlier in the thread, i.e. two AKG clip-ons going into a two-input preamp bodypack where the mix is done locally by me. Works for me. Until I get to be doing stadium gigs anyway.
Logged
there ain't no such thing as a free reed

vielleuse

  • Member
  • *
  • Offline Offline
  • Posts: 14
Re: Microphones and amplification
« Reply #38 on: October 21, 2009, 01:35:41 PM »

I have much sympathy with you, vielleuse, as I'm no sound engineer either.  Isn't the root of the problem that there isn't yet a really good answer available for miking boxes, and we're all compromising, without there being a consensus?

I looked at the pdf 'technical' document that you can read about the K&K system, and it seems to me anyone buying one can't tell in advance how much drop in signal you would get between a reed 2/3cm away from the mike, and one at the end of the keyboard (perhaps about 10/11cm away on your box?)  There's a polar diagram, but in the absence of a scale, and having only one pattern, you can't even estimate what the drop-off will be.  But from the response from the back of the mike, it certainly looks as if feedback could also be a problem, as IanD has pointed out. 

Ian, can you help us at all?

(Erm, this may be heresy, but do close miking systems for boxes actually work properly yet?  The more I understand about their inherent problems, the more I'm reaching the conclusion that they have some way to go.)



It also doesn't help that I'm really not technical, and don't have a huge amount of money. In the case of the hurdy-gurdy I only resolved it because a friend who is a luthier/guitar repairer and also fellow band member at the time got sick of me going on about it and gave me a K&K pickup and preamp he found knocking around, which works beautifully.
Logged

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Microphones and amplification
« Reply #39 on: October 21, 2009, 01:54:49 PM »

I agree that separate outputs are needed for treble and bass.

I agree too. But then the key question is who is responsible for the mix out front, and what does this imply for the kind of setup you want/need.
If you could rely on there always being a sound engineer out front who knew what sound you wanted/needed, and if you were playing primarily through a PA rather than backline, then I guess you would want to send the two channels separately out to the desk. And then you need to figure out what is your favourite affordable set up to achieve this, e.g. two standing mics, two clip-ons with separate pre-amps etc, or a combination of the two.
But for many of us these are pretty big ifs. In most settings I play principally through a backline amp and from there (if necessary) into PA, the latter mixed by me or another band member who has to make their own guesstimate about how its all sounding out front. So given this I'm happy to go with the convenience of a set-up described earlier in the thread, i.e. two AKG clip-ons going into a two-input preamp bodypack where the mix is done locally by me. Works for me. Until I get to be doing stadium gigs anyway.

From my perspective the mix is done by a band member and we don't have a big enough mixing desk for me to have separate inputs for treble and bass and let me play my uke as well. Several gigs we haven't had room for that. So having a single input pickup was important, as the alternative was just to not have my bass amplified.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog
Pages: 1 [2] 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal