Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3]   Go Down

Author Topic: cajun tuning?  (Read 6551 times)

0 Members and 1 Guest are viewing this topic.

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: cajun tuning?
« Reply #40 on: December 09, 2022, 11:00:15 PM »

Scratchers.

Here are some I made - just a very simple slim brass holder with a reed lifter in one end and a short length of solid carbide rod in the other, different sizes according to need.
The carbide rod is great as it is far harder than any reed and keeps an extremely sharp edge pretty much for ever.
The downside is that it is brittle and quite expensive, so dropping them is upsetting and best avoided.

I have another with a tiny length of 1mm rod set into the side of the tip of the brass holder, pointing backwards at 45 degrees or so like a little tooth or pick, which works nicely on small reversed reeds.
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: cajun tuning?
« Reply #41 on: December 09, 2022, 11:05:25 PM »

The best I have found are from Carini,  they are a tapered cylindrical tool like a round needle file, but smooth.  They are far superior to any of the others, and not much more expensive.

There used to be a little gift shop just aound the corner from The old Carini shop in Castelfidardo.
There was an old man there making those scratchers from needle files.
I bought mine 30 years ago and it's still my only scratcher.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Peter Cane

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 204
Re: cajun tuning?
« Reply #42 on: December 10, 2022, 11:41:17 AM »

Scratchers.

Here are some I made - just a very simple slim brass holder with a reed lifter in one end and a short length of solid carbide rod in the other, different sizes according to need.
The carbide rod is great as it is far harder than any reed and keeps an extremely sharp edge pretty much for ever.
The downside is that it is brittle and quite expensive, so dropping them is upsetting and best avoided.

I have another with a tiny length of 1mm rod set into the side of the tip of the brass holder, pointing backwards at 45 degrees or so like a little tooth or pick, which works nicely on small reversed reeds.

Those tools are really nicely made.
Could you please take a close up of the tips you used for scraping?
Can you please describe how you fashioned the brass handles and also how you fixed the scraper tips inside the brass?
Is the tip metal easily sourced?
Peter
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: cajun tuning?
« Reply #43 on: December 10, 2022, 01:12:34 PM »

Scratchers.

Here are some I made - just a very simple slim brass holder with a reed lifter in one end and a short length of solid carbide rod in the other, different sizes according to need.
The carbide rod is great as it is far harder than any reed and keeps an extremely sharp edge pretty much for ever.
The downside is that it is brittle and quite expensive, so dropping them is upsetting and best avoided.

I have another with a tiny length of 1mm rod set into the side of the tip of the brass holder, pointing backwards at 45 degrees or so like a little tooth or pick, which works nicely on small reversed reeds.

this kind of thing?.....seem to do them in 1mm / 1.5mm /2mm which seems about right.....not expensive as long as they are the right kind of material? packs of 10! how do they cut into smaller lengths? im definitely going to order the carini ones and will call in at the gift shop one day (thanks rees and theo!) https://www.ebay.co.uk/itm/144738498742?hash=item21b31638b6:g:ZfMAAOSw~qlizwxu&amdata=enc%3AAQAHAAAA4D1pjPPRft2Wj9HbehAozX7wf1h6B1JpyXj2kk1PVqghqKypGdHpYGIkWlv3VrINvrOr%2BbPZFWmASu0jYvAPGFV0yYch12fUjtJlvTRvLN%2FgnjnO0Vqh%2F5FTVOcCP%2FYF2iYL%2BL6q0JIWCVdtLa4UzlGBTjaRUCO%2BBfLjo4r3znbfwFC0S4BUo8NRPrgtQ3orbhX%2Bf8LM565IybiW%2FKKj2Nbn%2FAuPnnVKzUweArtO%2FwRzZClhAdcSPuJTQjqhyhsvtSxqxyV4HzW3zq3xvzhI5ejiCMpx5L6HuRfbd3S6LyOA%7Ctkp%3ABk9SR8iulcKfYQ
Logged

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: cajun tuning?
« Reply #44 on: December 10, 2022, 05:56:48 PM »

Scratchers.

Here are some I made - just a very simple slim brass holder with a reed lifter in one end and a short length of solid carbide rod in the other, different sizes according to need.
The carbide rod is great as it is far harder than any reed and keeps an extremely sharp edge pretty much for ever.
The downside is that it is brittle and quite expensive, so dropping them is upsetting and best avoided.

I have another with a tiny length of 1mm rod set into the side of the tip of the brass holder, pointing backwards at 45 degrees or so like a little tooth or pick, which works nicely on small reversed reeds.


this kind of thing?.....seem to do them in 1mm / 1.5mm /2mm which seems about right.....not expensive as long as they are the right kind of material? packs of 10! how do they cut into smaller lengths? im definitely going to order the carini ones and will call in at the gift shop one day (thanks rees and theo!) https://www.ebay.co.uk/itm/144738498742?hash=item21b31638b6:g:ZfMAAOSw~qlizwxu&amdata=enc%3AAQAHAAAA4D1pjPPRft2Wj9HbehAozX7wf1h6B1JpyXj2kk1PVqghqKypGdHpYGIkWlv3VrINvrOr%2BbPZFWmASu0jYvAPGFV0yYch12fUjtJlvTRvLN%2FgnjnO0Vqh%2F5FTVOcCP%2FYF2iYL%2BL6q0JIWCVdtLa4UzlGBTjaRUCO%2BBfLjo4r3znbfwFC0S4BUo8NRPrgtQ3orbhX%2Bf8LM565IybiW%2FKKj2Nbn%2FAuPnnVKzUweArtO%2FwRzZClhAdcSPuJTQjqhyhsvtSxqxyV4HzW3zq3xvzhI5ejiCMpx5L6HuRfbd3S6LyOA%7Ctkp%3ABk9SR8iulcKfYQ

That description is a bit misleading, they're HSS - not carbide.
However - yes, they would make fine scratchers and be less brittle than solid carbide.
To cut them, put a little groove around it with a thin cutting disc or diamond file, mount it in a vice with the notch level with the top of the jaw and then simply snap it.  That way there is no risk of overheating it and reducing the hardness.
If you cut right through with a cutting disc then go gently and have a wet cloth to cool the cut with regularly.  You have to get HSS extremely hot to damage it though, so you shoul be fine.
Logged

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: cajun tuning?
« Reply #45 on: December 10, 2022, 06:09:02 PM »

Scratchers.

Here are some I made - just a very simple slim brass holder with a reed lifter in one end and a short length of solid carbide rod in the other, different sizes according to need.
The carbide rod is great as it is far harder than any reed and keeps an extremely sharp edge pretty much for ever.
The downside is that it is brittle and quite expensive, so dropping them is upsetting and best avoided.

I have another with a tiny length of 1mm rod set into the side of the tip of the brass holder, pointing backwards at 45 degrees or so like a little tooth or pick, which works nicely on small reversed reeds.

Those tools are really nicely made.
Could you please take a close up of the tips you used for scraping?
Can you please describe how you fashioned the brass handles and also how you fixed the scraper tips inside the brass?
Is the tip metal easily sourced?
Peter

Peter - they're pretty crude really! They were knocked up quickly for functionality rather than appearance.

The brass handle is simply a length of thin brass rod with the end tapered down in the lathe and a hole bored in each end.
The reed lifter and scraper tip are inserted just a few mm and bonded in with a tiny drop of Loctite.
The scraper tip is just ground square across and as near dead flat as possible on a fine diamond plate.

The metal used for the scrapers is solid carbide toolbits 1, 1.5 and 2mm dia - but see Chris's post, HSS would be fine - not quite as hard, but quite hard enough, cheaper, and less brittle.
Logged

Peter Cane

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 204
Re: cajun tuning?
« Reply #46 on: December 10, 2022, 07:31:51 PM »

Scratchers.

Here are some I made - just a very simple slim brass holder with a reed lifter in one end and a short length of solid carbide rod in the other, different sizes according to need.
The carbide rod is great as it is far harder than any reed and keeps an extremely sharp edge pretty much for ever.
The downside is that it is brittle and quite expensive, so dropping them is upsetting and best avoided.

I have another with a tiny length of 1mm rod set into the side of the tip of the brass holder, pointing backwards at 45 degrees or so like a little tooth or pick, which works nicely on small reversed reeds.

Those tools are really nicely made.
Could you please take a close up of the tips you used for scraping?
Can you please describe how you fashioned the brass handles and also how you fixed the scraper tips inside the brass?
Is the tip metal easily sourced?
Peter

Peter - they're pretty crude really! They were knocked up quickly for functionality rather than appearance.

The brass handle is simply a length of thin brass rod with the end tapered down in the lathe and a hole bored in each end.
The reed lifter and scraper tip are inserted just a few mm and bonded in with a tiny drop of Loctite.
The scraper tip is just ground square across and as near dead flat as possible on a fine diamond plate.

The metal used for the scrapers is solid carbide toolbits 1, 1.5 and 2mm dia - but see Chris's post, HSS would be fine - not quite as hard, but quite hard enough, cheaper, and less brittle.
Graham..it's the diamond stone which is the important bit and also the " just honed square " bit!!! Ha ha.
Imo, it's the finish and the angle of it at the tip which is vital.
I am wondering if a reed scraper has the same principle as a woodwork cabinet scraper which is a piece of carbon steel sheet.
But it is how the scraper edge is achieved which is the crux of whether it will work or not.
Briefly the edge is turned over by running a highly polished round steel bar along the edge but at the right angle.
This creates a tiny burr all along the edge of the scraper.
I have done it quite a few times and it was always touch and go if I did it right.
When done right it will take off a long shaving of wood which is so satisfying.
When done incorrectly it will produce dust, no smile and a grunt.
I am very interested to know whether our steel reed scraper would work better with that principle.
I tried to google the shop in Italy but my phone would not allow it as it's a dodgy site or something ridiculous.
I will try from my pc in the morning.
I don't mind spending money on essential tools of the trade.
I have already ordered a reed tuning set from Charlie last week.
I have made my reed lifters and wrapped the handles with very thin leather scraps. Very posh and nice to use.
Peter
Logged
Pages: 1 2 [3]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal