Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Tuning long plates (a Chemnitzer)  (Read 849 times)

0 Members and 1 Guest are viewing this topic.

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Tuning long plates (a Chemnitzer)
« on: March 06, 2021, 01:28:31 AM »

Tuning a lovely burlwood Pearl Queen with abalone buttons and steel reeds on long plates.  It seems to be hovering around A=450 (!) right now.  My preference is to bring it to A=440. but I'm open to input from Chemnitzer aficionados.  Is this sacrilege?

For tuning, my going plan is to play each key and write down the pitches, take out the plates, rough tune using the ping tones as a guide, reassemble, and repeat to fine tune.

There is a post (http://forum.melodeon.net/index.php/topic,24060.msg286687.html#msg286687) in which RogerT describes making a jig for testing long plates.  I imagine that the slots would have to be of different lengths to accommodate different sections of the trapezoidal reedplate.  If I go this route, my solution might be to make a single |_| shape of wood+gasket, and let the fourth side be separate so that it can slide up and down to adjust the height.  (Hope that makes sense.)

It might also be possible to hold the long plate against a standard reedblock that has been fitted with gasket material.

Any tips from those who have been this way before?
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning long plates (a Chemnitzer)
« Reply #1 on: March 06, 2021, 08:53:14 AM »

I don’t think ping tones will get you very close.  Suggest you try measuring ping tones in situ fir a few reeds and compare with the pitch when sounded normally. Ping tones always sound quite sharp to my ear.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Tuning long plates (a Chemnitzer)
« Reply #2 on: March 06, 2021, 09:56:34 AM »

Tuning a lovely burlwood Pearl Queen with abalone buttons and steel reeds on long plates.  It seems to be hovering around A=450 (!) right now.  My preference is to bring it to A=440. but I'm open to input from Chemnitzer aficionados.  Is this sacrilege?

For tuning, my going plan is to play each key and write down the pitches, take out the plates, rough tune using the ping tones as a guide, reassemble, and repeat to fine tune.

There is a post (http://forum.melodeon.net/index.php/topic,24060.msg286687.html#msg286687) in which RogerT describes making a jig for testing long plates.  I imagine that the slots would have to be of different lengths to accommodate different sections of the trapezoidal reedplate.  If I go this route, my solution might be to make a single |_| shape of wood+gasket, and let the fourth side be separate so that it can slide up and down to adjust the height.  (Hope that makes sense.)

It might also be possible to hold the long plate against a standard reedblock that has been fitted with gasket material.

Any tips from those who have been this way before?
I haven't tried this yet but been thinking about a full re-everything of my Antoria....I envisage cutting a piece out of a camping mat (conforming material, 8 -10mm thick) and cutting a reed sized window in it. Mat on tuning table, window over table hole position long plate according to taste. Bear in mind that the window size determines the uplift force for any given pressure and this is like to be no more than about an ounce accross the whole area of the window.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tuning long plates (a Chemnitzer)
« Reply #3 on: March 06, 2021, 10:05:10 AM »

For tuning, my going plan is to play each key and write down the pitches, take out the plates, rough tune using the ping tones as a guide, reassemble, and repeat to fine tune.

Pinging the reed rarely results in a stable pitch for long enough duration which you can measure with a tuning meter.

Making some sort of a jig as you describe would be one way to go, although you would still have tune by offsets from your in situ readings, as the jig won't reproduce the true acoustic environment of the assembled instrument.

Why not use the instruments own bellows as a tuning bellows? Make a |_| shaped frame from 9 mm plywood which you can clamp horizontally to a bench or table, and use the arms of the frame (suitably sanded smooth) to suspend the instrument from its bellows folds. You can then rest the instrument end on the bellows and sound the reeds individually just by working the bellows and pressing the buttons.

More details in this post.
and this one, including a photo.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Tuning long plates (a Chemnitzer)
« Reply #4 on: March 06, 2021, 10:20:00 AM »

Can't you get into the reeds on the job? (I've never seen the internals of a chemnitzer.) When I've done long plate reeds on my old (read scrapper!) melodeons, I've tuned the top reeds in place, and turned the plates over onto the other side of the matching block to do the others. It beats clarting about with hooks and stuff! 
As the experts on here keep telling us, it's quicker, and therefore ultimately easier (once you get the knack) to tune in place rather than on a separate tuning rig. It does away with the need to record all the note variations, for a start, as you only need to tune the reed once to get where you want.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Re: Tuning long plates (a Chemnitzer)
« Reply #5 on: March 06, 2021, 03:23:26 PM »

Thanks very much for the replies.  Steve, I like your bellows frame idea for melodeons, but the Chemnitzer probably falls under "heavier instruments" as described in your post.  It's robustly constructed, so maybe I'm worrying too much, but I'm happy to spend the time dealing with the two machine bolts when removing the end.

I like the idea of using a thick, firm, more easily cut material, like camping mat, instead of plywood, for the base of a small tuning jig -- thanks Peadar.  I'll experiment today.
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Tuning long plates (a Chemnitzer)
« Reply #6 on: March 09, 2021, 08:20:18 AM »

I’ve tuned three or four of these. I make a flat slotted jig, with a craft foam gasket, and sit the plate on that over the (pedal) tuning table. But for tweaking to get octaves in unison (if you have those) you have to lift the end on and off the bellows. This does work quite well, actually, though I’ve made a polystyrene supports for the end on the (padded) bench top, to prevent buttons being pressed below. I don’t have a jig or anything. The instrument sits quite stable on its end. The plates are held on with L shaped screws and I have a little slot ended tool (actually it’s a lever bender) which works like a key, to speed the plate on/plate off process, which mostly you will have to do for the inside reeds. The valves I make by cutting down plastic valves. The big problem, of course, is if you have broken reeds. I’ve sent the plate to Harmonikas a couple of times...it ( used to ) cost €25 per tongue, but they can be very lax in reading the instructions and on both occasions I had to send it back.
One word of warning...when you’ve removed the end screws this means the Reed pan assembly and the cover are no longer attached to each other. It’s very easy to pick it all up and then the reeds/lever assembly will drop out. So first time be v careful (after that I tape them together to prevent accidents).
« Last Edit: March 09, 2021, 08:23:35 AM by RogerT »
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal