Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: How do bellows pins work?  (Read 6442 times)

0 Members and 1 Guest are viewing this topic.

Keithypete.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 917
How do bellows pins work?
« on: October 14, 2009, 01:03:28 PM »

 A very basic question : How does a bellows pin work? I've used some very big nails with all sorts of dull/matt finishes to aid grip, some even have annular ring shanks or even a cross section like this : +. So how do bellows pins work when they are short, smooth and very shiny! Is it to do with a slight mis-alignment of the holes? I ask because an old melodeon I have come by has some very loose bellows pins. Thanks everyone.
Logged
Beltuna Sara II - B/C flavour.
Borsini - G,D,A.
Pokerwork B/C.
PRIMATONA IV, B/C.

triskel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3290
Re: How do bellows pins work?
« Reply #1 on: October 14, 2009, 01:21:58 PM »

They work through friction - they need to be a tight fit in the holes. If they've become loose, you need to replace them with thicker ones.

But the substitutes you mention will only make the problem worse, because they're bound to enlarge the holes every time they're used.

Keithypete.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 917
Re: How do bellows pins work?
« Reply #2 on: October 14, 2009, 01:28:23 PM »

Thanks for that. Would a solution be to simply move the pin position slightly and start again with the same pins?
Logged
Beltuna Sara II - B/C flavour.
Borsini - G,D,A.
Pokerwork B/C.
PRIMATONA IV, B/C.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: How do bellows pins work?
« Reply #3 on: October 14, 2009, 01:55:22 PM »

What I do is get a large pair of electicians pliers and add a few crimps along thelength of the pin and it then holds quite happily

Keithypete.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 917
Re: How do bellows pins work?
« Reply #4 on: October 14, 2009, 02:00:59 PM »

Seems less problematical. Do they have any other special properties? Are they rust-proof/stainless, for example?
Logged
Beltuna Sara II - B/C flavour.
Borsini - G,D,A.
Pokerwork B/C.
PRIMATONA IV, B/C.

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: How do bellows pins work?
« Reply #5 on: October 14, 2009, 02:13:48 PM »

Generally, the Hohner pins are plated steel and the fatter Italian pins are plated brass.

If the bellows gasket has become compressed, fitting new gasket will usually tighten the pins.
If the pins are really sloppy in the holes it's best to fill the holes and then re-drill.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How do bellows pins work?
« Reply #6 on: October 14, 2009, 02:16:09 PM »

What I do is get a large pair of electicians pliers and add a few crimps along thelength of the pin and it then holds quite happily

Though that has the same detrimental effect as described by Triskel above.

If the holes are seriously enlarged you could try filling the holes with superglue and wood dust. As shown in these photos, click forward to see the next two.  When I did this I left the pins in place while applying the glue.  They were new and shiny so the glue didn't bond to them, and a sharp tap freed them after the glue had set.

Do not do this with the bellows frames assembled to the end of the box!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: How do bellows pins work?
« Reply #7 on: October 14, 2009, 02:24:44 PM »

click forward to see the next two....
Theo - clicking forward doesn't seem to be working for me. I can only see the first photo.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Keithypete.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 917
Re: How do bellows pins work?
« Reply #8 on: October 14, 2009, 02:46:53 PM »

click forward to see the next two....
Theo - clicking forward doesn't seem to be working for me. I can only see the first photo.


Me too!
Logged
Beltuna Sara II - B/C flavour.
Borsini - G,D,A.
Pokerwork B/C.
PRIMATONA IV, B/C.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How do bellows pins work?
« Reply #9 on: October 14, 2009, 04:48:12 PM »

Here is a public link to the whole album, its picture numbers 35,36 and 37, on the second page.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

TomB-R

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 598
Re: How do bellows pins work?
« Reply #10 on: October 16, 2009, 01:27:06 PM »

FWIW I like to make reasonably sure that I put each bellows pin back where it came from.
Logged

Keithypete.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 917
Re: How do bellows pins work?
« Reply #11 on: October 16, 2009, 02:40:04 PM »

Am I right in thinking that some makers (Saltarelle ?) use/did use a screw & cup arrangement?
Logged
Beltuna Sara II - B/C flavour.
Borsini - G,D,A.
Pokerwork B/C.
PRIMATONA IV, B/C.

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: How do bellows pins work?
« Reply #12 on: October 16, 2009, 02:55:39 PM »

Not on the recent ones I've seen/played/owned.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: How do bellows pins work?
« Reply #13 on: October 16, 2009, 04:38:13 PM »

Am I right in thinking that some makers (Saltarelle ?) use/did use a screw & cup arrangement?
Bernard Loffet uses cross-head screws instead of bellows pins on some of his instruments (the smaller ones I think).
To my mind with screws, especially the smaller diameter ones, there is a risk of wearing out the threaded portion of the hole in the wood with repeated unscrewing and reassembling for tuning and maintenance. I much prefer the idea of bellows pins. 
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Ebor_fiddler

  • Chris
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2340
  • Hohner 1040 C One-Row, Sandpiper D/G, Liliput C/F
    • Ebor Morris
Re: How do bellows pins work?
« Reply #14 on: October 16, 2009, 11:44:00 PM »

My first melodeon, bought around 1969 was of unknown brand, but Hohner clone "Made in GDR" and this had screws rather than pins, so I was extremely surprised to find what I thought were nails holding my modern Scarlatti together (though the pins on my Houner one-row ought really to be thought of as nails as they have crudely pointed ends).
 :'(
Logged
I'm a Yorkie!
My other melodeon's a fiddle, but one of my Hohners has six strings! I also play a very red Hawkins Bazaar in C and a generic Klingenthaler spoon bass in F.!! My other pets (played) are gobirons - Hohner Marine Band in C, Hohner Tremolo in D and a Chinese Thingy Tremolo in G.

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: How do bellows pins work?
« Reply #15 on: October 17, 2009, 07:06:03 AM »

Gaillard uses a strange narrow steel pin with a double head. It is easy to shift without bruising the wood, but the double head catches in your pullover (I think) and I managed to lose a couple early on despeite them feeling reasonably tight in their holes. I never found them. Sadly they seem impossible to source in UK. I've since bought a set, and given any remotely loose ones a tiny flex to tighten them.

Any new player should probably ease his pins out (one end only) and look inside at some stage. You'll be forced to do it one day when a reed jams. On older boxes particularly try and get that pin back into the same hole. Holes enlarge and someone may have tweaked the pin to fit.

Another tip when you open your box is to biro name/postcode into a clean bit of wood (just in case).
Logged
  _       _    _      _ 

TomB-R

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 598
Re: How do bellows pins work?
« Reply #16 on: October 17, 2009, 01:25:43 PM »

Another tip when you open your box is to biro name/postcode into a clean bit of wood (just in case).
That can be nice for the future quite apart from the security aspects.
When refurbishing a grey Double Ray I was pleased to find "Danny Byrne, September 1959" and an address in Donegal written inside.

(Isn't this forum great! A two page discussion on bellows pins! Sorry folks, didn't mean to make anyone feel self conscious!  ;D )
Tom
Logged

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: How do bellows pins work?
« Reply #17 on: October 17, 2009, 04:08:37 PM »

I am still waiting to find one that belonged to Kilroy (:)
Logged

jack

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 114
Re: How do bellows pins work?
« Reply #19 on: March 05, 2010, 08:32:45 PM »

..but where can you get them?

I've just acquired an Erica with four missing and the local ironmongers couldn't come close to a match..
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal