Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Air leaks on a Hohner Presswood  (Read 1952 times)

0 Members and 1 Guest are viewing this topic.

David Knight

  • Member
  • *
  • Offline Offline
  • Posts: 8
Air leaks on a Hohner Presswood
« on: April 03, 2021, 11:41:39 AM »

I’m hoping the amazing collective skills and experience of this forum can help me!

My Hohner Presswood seems to have developed air leaks on the corners where the snakeskin paper is folded over to join the bellows to the wooden box. My plan was to glue small patches of similarly patterned paper over the corners using bookbinders PVA glue. I’d welcome any feedback on this approach and also advice on where to source the snakeskin design paper.

Many thanks, David
Logged
Castagnari 1914 DG, Hohner Presswood DG

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Air leaks on a Hohner Presswood
« Reply #1 on: April 03, 2021, 11:52:06 AM »

The paper should in no way be providing an air seal. My best guess is that the bellows end gasket has degraded and is leaking. You can buy replacement HERE

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Air leaks on a Hohner Presswood
« Reply #2 on: April 03, 2021, 12:17:52 PM »

Se-ing the pic if you mean were the bellow folds join the wood (large end frame on this model),not the latter bellows gaskets then the leak could well be worn corners ? But it may well be the entire joint were the bellows are glued to the end frames. The gasket should be replaced if suspect first. Depending on the size and location of the hole/leak at the corners they are based patched from the inside with a fine linen type cloth.Pva will do as a glue.The tricky thing is not to let glue get onto hte folds as you compress while drying ,I put some plastic bag in the folds. Best with the bellow off and if you dont have or improvise a bellows press ,a bit of wood with a weight on will do compress to nearly dry but I would the release pressure to check no rouge glue sticking before fully dry to sort out any such errors. If the leak is  at the actual glue join of bellow to frame the this can be gently prised apart and reglued.There is plenty of info if you search these threads here. Do check bellows gaskets first. The corners are actualy never 100% airtight by design so dont get obsessed by that.The leak is prob between the end paper and wood frame. The paper on the outside is a cosmetic cover so the end should be glued from the inside. You with skill wont have to break the joint complete so parting the outer paper work from the inside glue ,and compress while drying. You have no bellows pins but two screws at each end behind the back plate should be holes in plate and strap and behind front cover. Be gentle not to break the inner clasps (more work)and with good bellows end gaskets you dont need to over tighten when reassembling.Keep the screws in original locations


« Last Edit: April 03, 2021, 12:29:07 PM by folkloristmark »
Logged
Mark Taylor
Folkloristmark

David Knight

  • Member
  • *
  • Offline Offline
  • Posts: 8
Re: Air leaks on a Hohner Presswood
« Reply #3 on: April 03, 2021, 12:25:21 PM »

Thanks for your speedy replies Lester and Folkloristmarc. It's really helpful to understand that I'm not aiming for 100% airtightness but I can feel a stream of air from the corners, so does that seem excessive? I'll try the bellows gasket first.

I've just watched Rich Edwards replace his bellows gasket on youtube

https://youtu.be/Y_77kaDEpOU

It looks as if I need to do the same.
Logged
Castagnari 1914 DG, Hohner Presswood DG

Chris Marriott

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1048
Re: Air leaks on a Hohner Presswood
« Reply #4 on: April 03, 2021, 12:32:27 PM »

Replacing the bellows gasket is really easy. Even I, who am hopeless at any form of DIY, managed it without difficulty on my Pokerwork. I bought the gasket tape from Charlie Marshall at GCM.
Logged
Chris

Castagnari Mory, English Concertina and Piano Accordion.

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Air leaks on a Hohner Presswood
« Reply #5 on: April 03, 2021, 12:33:39 PM »

Have amended my post while you were posting its prop the glue joint between the paper ends and the wood end frames.Its the glue that forms the seal not the outer paper.The original would be hide glue PVA will do or a modern hide glue type.heat and a very little water better kettle steam will help work a hide glue seal Pva is more perm went dry hense the advise on rouge glue seepings.
Logged
Mark Taylor
Folkloristmark

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Air leaks on a Hohner Presswood
« Reply #6 on: April 03, 2021, 12:36:13 PM »

Thanks for your speedy replies Lester and Folkloristmarc. It's really helpful to understand that I'm not aiming for 100% airtightness but I can feel a stream of air from the corners, so does that seem excessive? I'll try the bellows gasket first.

I've just watched Rich Edwards replace his bellows gasket on youtube

https://youtu.be/Y_77kaDEpOU

It looks as if I need to do the same.
Good video but you should note that your box is built differently and the ends are held on by two screws on each end under their respective grilles. In fact you may get away with just nipping these screws up a bit to improve the seal which is probably (if still in its original state) just provided by some candlewick string.

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Air leaks on a Hohner Presswood
« Reply #7 on: April 03, 2021, 12:40:55 PM »

Yours is a diifferent set up.Replace bellows gasket is the same but the glue joint on yours to the actual very wide bellow end is quite away back from that bellows joint so do you meen the bellows corner at gasket face or corner at the actual end of the fold off the bellows should be easy on yours to determine the difference. On the latter usual vid model both these joints are right next to each other as the bellows end is a small wood end so it hard to tell glue seal from gasket hence good advice that it is usually the gasket.Your is different early model so I think I am clear you mean actual corner at last fold which is the glue seal

« Last Edit: April 03, 2021, 12:44:06 PM by folkloristmark »
Logged
Mark Taylor
Folkloristmark

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Air leaks on a Hohner Presswood
« Reply #8 on: April 03, 2021, 12:47:39 PM »

If its the glue joint work from the inside and you can with skill keep the cosmetic look of the outside.
With respect to Lesters advice only nip up the screw if they are not tight. If you overtighten on your model there is a risk of pulling the inner clasps off. :-\

How about a Lester video on early Club model 1 end wood frame replacement. Its needed  :M
« Last Edit: April 03, 2021, 12:53:55 PM by folkloristmark »
Logged
Mark Taylor
Folkloristmark

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Air leaks on a Hohner Presswood
« Reply #9 on: April 03, 2021, 12:54:40 PM »

....is that a Fraton Box ?....
Logged

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Air leaks on a Hohner Presswood
« Reply #10 on: April 03, 2021, 12:59:07 PM »

here
Logged
Mark Taylor
Folkloristmark

David Knight

  • Member
  • *
  • Offline Offline
  • Posts: 8
Re: Air leaks on a Hohner Presswood
« Reply #11 on: April 03, 2021, 01:07:26 PM »

Hi, thanks for all the replies- yes I bought the box from Fraton and I’m realising that the design is very different from a Pokerwork. Folkloristmark, the leak is coming from where the finger on the right of your picture is pointing!
Logged
Castagnari 1914 DG, Hohner Presswood DG

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Air leaks on a Hohner Presswood
« Reply #12 on: April 03, 2021, 01:08:14 PM »

I've just watched Rich Edwards replace his bellows gasket on youtube

A 45 degrees angle where the ends of the gasket meet makes it easier to prevent a gap.
Logged

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Air leaks on a Hohner Presswood
« Reply #13 on: April 03, 2021, 01:24:54 PM »

Ok my right or viewers right?You know that answer.

assuming if its the glue joint or a hole in that corner gasket. If the box is from fratton the the gaskets will have been renewed and most advice is about the gasket on a latter model .You could place baby powder talk around the bellows to see the leaks this smells nice but is messy you will see puffs of dust from the leak area. I recommend you remove the bellows and look at the end glue joint from inside. Pull the bellows open and look to see any light coming throught the corners to eliminate them and then the glue joint.
You may see the glue has become brittle and work from the inside  removing as much glue as you can I would start dry scrapping it with sharp knife becarefull not to rip the paper. Reglue from inside and compress till dry. The amount of work depends on the condition of the box but as this is a fratton box i would hope any issue is minor. If there is a hole in the corners patch from the inside with linen cloth covered in PVA but cover with a think plastic stop the outsides glueing the fold together if it glues to the stop material fine it can be removed but you dont want it joining together.

If you mean the gasket then just remove bellows and check replace it. Bcause of the way these early models are pulled together by screws not bellows pins you the with of the bellows seal can very quite a bit so its easier in that respect. Just dont force the scews overtight the seal should seal not the screwforce.
« Last Edit: April 03, 2021, 01:34:51 PM by folkloristmark »
Logged
Mark Taylor
Folkloristmark

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Air leaks on a Hohner Presswood
« Reply #14 on: April 03, 2021, 01:30:02 PM »

That box has been fitted with new bellows, so the glue holding it to the end frames is probably a modern glue.  It does look as if the glued joint is a possible source of leakage.  because it's modern glue it won't be easy to remove and re-glue, you will just have to try and identify the gap and get some glue into it.

Another source of leakage is the corner joints of the bellows frame.  If this is not sealed it can allow leaking air to track along the corner so the place it is emerging on the outside might not match exactly with where the leak starts on the inside.

With any leak repairs it's important to be sure you have identified the leak before applying adhesive!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Air leaks on a Hohner Presswood
« Reply #15 on: April 03, 2021, 01:36:03 PM »

Well put Theo.
Logged
Mark Taylor
Folkloristmark

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Air leaks on a Hohner Presswood
« Reply #16 on: April 03, 2021, 01:39:38 PM »

I "borrowed with pride" (nicked  ::) ) the concept for my G/C Box....

Mine is as tight as a 'tight thing', I used the adhesive backed high cell foam for the seal, but it doesn't look as if that is your problem, but hopefully not difficult to resolve and very pretty boxes....


If I recall correctly, there is a linen tape between the card of the bellows and the wood of the frame.  The bellows 'paper' over laps onto the tape and the old paper/new leather, extends over tape and paper and has to do so by sufficient, with the tape to provide the seal

At the corner itself there is a bit of a build up of tape/paper/finish material unless it is 'V'd perfectly.  I am not sure this is therefore a glue issue per se, depending on how Fratons fixed the leather.....ie.....where the joint is in the strip they used?

The leather, if it covers the corner joints, should be sealing the corners and I would not expect them to join it 'at' the corners for obvious reasons?

If it is indeed a failure of the tape join inside, so as not to have to spoil the outside, .....given a choice of tape to use "inside" I would opt for Bookbinders tape.......in an overly wide profile ?




 
« Last Edit: April 03, 2021, 01:54:06 PM by Nigel.H »
Logged

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Air leaks on a Hohner Presswood
« Reply #17 on: April 03, 2021, 01:57:49 PM »

again from the inside check the wood to wood joints that inside under that silver wear.They should be easy to run a glue over if they leak.find the leak before the remedy. Frattons boxes are good so its likely only a small area.Or post the bellows back to Fratton what key is the box?
Logged
Mark Taylor
Folkloristmark

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Air leaks on a Hohner Presswood
« Reply #18 on: April 03, 2021, 03:51:44 PM »

Not sure if these might help direct you to where the air might be getting out and seeing the necessary overlap and corner detail.....

Getting the corners off - if you have to and hopefully you may not - is a knack as it is a very long 'pin', quite weak for it's length and the corners bend out of shape easily.  The pins don't all come out fit to be reused in my experience, but you can use an old Hohner reed fixing pin, although they are a little shorter.  The head is pretty much indistinguishable in use.  Replicating whatever Fraton used as 'Alligator' paper precisely may prove difficult for an "external" fix as it will probably not be a standard material ( or colour ).

Having stripped to the wood and re-taped and applied the leather to mine recently, if you can get a solution from the inside it may pay.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Air leaks on a Hohner Presswood
« Reply #19 on: April 03, 2021, 05:29:00 PM »

There should be no need to disturb the fake alligator skin.  All the places you could seal are accessible from inside.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal