Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Metal pallets  (Read 1523 times)

0 Members and 1 Guest are viewing this topic.

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Metal pallets
« on: April 24, 2021, 10:34:53 AM »

I have an old Koch with metal pallets which are soldered onto their arms. What is the best way to reface them?

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Metal pallets
« Reply #1 on: April 24, 2021, 10:56:00 AM »

I have one like this too John and I’m pondering the same thing.  I have three possibilities so far:
1 reface as they are and hope they stay airtight.
2 unsolder the metal pallets from the arms and resolder after assembly. (Might singe the felt?)
3 unsolder the metal pallets and replace with wood.

Unless there is a better idea I’ll probably go with 2.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Metal pallets
« Reply #2 on: April 24, 2021, 11:05:03 AM »

Another thought I have had, is to take the whole treble mechanism off.

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Metal pallets
« Reply #3 on: April 24, 2021, 11:05:49 AM »

Assuming it is the same design as a later Pokerwork, barring the solder rather than 'gloop' holding the pallets and bearing in mind my ability to upset those who know better than I, so tin hat in place; facing the issue of a 'rusty' mechanism that I wanted to soak in Muriatic Acid, I used a large rubber band to 'restrain' the levers with the fingerboard, then released the small screws that hold the spring "assy" to the Fondo and the F/board screws.  That gave me a unit comprising the fingerboard & lever assy as one.  It didn't have the pallets on because that wasn't the issue I was resolving, but, faced with soldered on pallets needing refacing, that is probably how I would attack it. 

You would have a manageable unit which was still 'all up together', hopefully no undue pressure on the solder joints, free access to the pallet faces without risk of bending out of line and the whole thing goes back together as one without needing three pairs of hands for the re-fitting.

But I bet there is a better way  ;) 8)
 
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Metal pallets
« Reply #4 on: April 24, 2021, 11:46:36 AM »

Yes of course removing the keyboard is part of the process, and also important for cleaning, checking springs etc.  The problem is getting the refaced pallets airtight.  If you reface the pallets without taking them off the levers it’s almost inevitable that there will be many tiny air leaks because the geometry has changed slightly so the pallets don’t sit exactly parallel to the fondo.  In theory you can adjust the pallets by bending the levers to get them to lie flat, but in practice it’s a long tricky job and the results are often less than perfect.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Metal pallets
« Reply #5 on: April 24, 2021, 12:11:12 PM »

I seem to remember someone on here solving a similar problem by melting the solder when the pallet was in situ. The pressure on the spring, pushed the pallet flat, and the solder reset. maybe I imagined it :)

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Metal pallets
« Reply #6 on: April 24, 2021, 12:17:44 PM »

I have one like this too John and I’m pondering the same thing.  I have three possibilities so far:
1 reface as they are and hope they stay airtight.
2 unsolder the metal pallets from the arms and resolder after assembly. (Might singe the felt?)
3 unsolder the metal pallets and replace with wood.

Unless there is a better idea I’ll probably go with 2.

How about Option 2 but instead of resoldering, make some leather discs or straps to go over the lever arms (like concertina pad fixings) and use hot melt glue to fix everything together. Would that work, do you think? 
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Metal pallets
« Reply #7 on: April 24, 2021, 01:18:11 PM »

That’s another possibility yes.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Metal pallets
« Reply #8 on: April 24, 2021, 01:48:56 PM »

The beast in question

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Metal pallets
« Reply #9 on: April 24, 2021, 02:39:20 PM »

If the pallet facing isn’t moth eaten you might get away with just giving the pallet facings a good scrub with a fine wire brush.  You would have to take the keyboard off to do that.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Metal pallets
« Reply #10 on: April 24, 2021, 03:07:53 PM »

Having seen the picture, I would be tempted to go with Theo's option 2.  Maybe use pliers to sink the heat and protect the felt ?
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Metal pallets
« Reply #11 on: April 24, 2021, 04:37:24 PM »

How about Option 2 but instead of resoldering, make some leather discs or straps to go over the lever arms (like concertina pad fixings) and use hot melt glue to fix everything together. Would that work, do you think?

That's what I usually do.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Metal pallets
« Reply #12 on: April 24, 2021, 05:42:03 PM »

I have one like this too John and I’m pondering the same thing.  I have three possibilities so far:
1 reface as they are and hope they stay airtight.
2 unsolder the metal pallets from the arms and resolder after assembly. (Might singe the felt?)
3 unsolder the metal pallets and replace with wood.

Unless there is a better idea I’ll probably go with 2.
I repaired an old PA with pallets like this and adopted no.3, though I had to make the pallets as they were a weird size. Cutting the groove in the back was the biggest difficulty, closely followed by chamfering the edges.

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Metal pallets
« Reply #13 on: April 24, 2021, 06:15:45 PM »

All great ideas, but I want to keep this box as original as possible. So I think I may opt for the unsolder in situ option. Then I can solder the refaced pallets as they sit over the holes, with the spring tension holding them down. That should ensure they are flat. Pinkies crossed.

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Metal pallets
« Reply #14 on: April 24, 2021, 07:29:35 PM »

All great ideas, but I want to keep this box as original as possible. So I think I may opt for the unsolder in situ option. Then I can solder the refaced pallets as they sit over the holes, with the spring tension holding them down. That should ensure they are flat. Pinkies crossed.

SJ

Good call. The originals would almost certainly have been soldered in position. Common or garden electrical solder will be fine. clean really well - emery or similar and use flux-and a hot iron with a reasonable size bit. I would suggest one of the old  stove top heated irons (never worked out why soldering irons are made of copper) at red heat. a light touch of a really hot iron at joint and the contact area you want to solder goes up to soldering temprature. get the iron away quickly and it cools without pumping loads of heat into the pallet which is where your felt burning risk would arise from a slower heating process.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal