Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Hohner Morino Club  (Read 5443 times)

0 Members and 1 Guest are viewing this topic.

howard mitchell

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 456
    • Howard Mitchell
Re: Hohner Morino Club
« Reply #20 on: September 30, 2022, 10:39:37 AM »

I can see from the first photo that there are 4 wires connected to the din socket on the left, Red, yellow, violet, black.  It looks as if they go all the way across to the far right and the black and red go to what looks like a regulator on a black heat sink and the other two to a connector on the board. It seems likely that the red and black are the power supply and yellow and violet the midi out. The regulator should have a number on it something like 7805. If that is the case the 05 indicates that it’s a 5v regulator so it will need an input voltage of at least 7v - a 9v power supply would be ok.

All of this needs verifying of course.

Is the connector next to the din socket a jack socket? Does it go to the internal mic shown in one of the other photos?


Logged
Saltarelle D/G, Hohner D/G, Hohner C/F, Dallape C/F, Hohner A/D, Gaillard G/C, Sagne D, Roland FR18D, Hohner Bb/Eb.

JD

  • Regular debater
  • ***
  • Online Online
  • Posts: 235
Re: Hohner Morino Club
« Reply #21 on: September 30, 2022, 02:20:46 PM »

The first thing that jumped out at me was the mounting of the reeds on the treble side. I assume those are the "L" reeds mounted parallel to the fondo. Is that a bit like the arrangement in a Preciosa but on a larger scale?

Shame we can't quite see the labeling of the chips on the board. I would agree with Howard that there is probably a 7805 regulator mounted on the heatsink. If that is the case then the power for the board is coming from the 240deg DIN socket, probably 9 volts. So the four wires from the DIN would be 0v, 9v and MIDI out and possibly 5v out. That allows the interface box to provide power for the MIDI electronics and the three wires required for the standard MIDI interface without any extra electronics actually inside the box.


It looks like the internal microphone is connected to the extra jack socket on the case. This is a rare beast.


When was this installation done I wonder. 1980s or 90s?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Morino Club
« Reply #22 on: September 30, 2022, 03:04:06 PM »

The first thing that jumped out at me was the mounting of the reeds on the treble side. I assume those are the "L" reeds mounted parallel to the fondo. Is that a bit like the arrangement in a Preciosa but on a larger scale?

Not the same apart from the orientation.  Those reeds are in a cassotto chamber.

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mayord21

  • Good talker
  • **
  • Offline Offline
  • Posts: 58
Re: Hohner Morino Club
« Reply #23 on: September 30, 2022, 03:42:31 PM »

Thanks Howard and JD for your analysis;

Indeed you are correct. It is a 7805 regulator. pics attached.

Don.
Logged

howard mitchell

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 456
    • Howard Mitchell
Re: Hohner Morino Club
« Reply #24 on: September 30, 2022, 04:08:43 PM »

The large IC EF68B50 is a UART, proving the serial output for the MIDI interface. It looks like it’s connected to the smaller chip CD74HCT03 next to it. This is an open drain nand gate which provides the driving current for the MIDI output. It normally has a 220 ohm resistor from its output to one of the midi pins and the other pin is connected to +5 volts via another 220ohm resistor. Right next to the adjacent connector for the yellow and violet wires are two resistors colour coded red, red, brown = 220 ohms.

I’d say there’s a good chance you’ll be able to connect a 9v power supply and split off a standard midi signal to go to a synth of your choice. It just needs some probing with a meter to verify all of this and check the polarity of the power supply and the midi connections.

From the date codes on the chips I’d say this was made about 1987.
Logged
Saltarelle D/G, Hohner D/G, Hohner C/F, Dallape C/F, Hohner A/D, Gaillard G/C, Sagne D, Roland FR18D, Hohner Bb/Eb.

mayord21

  • Good talker
  • **
  • Offline Offline
  • Posts: 58
Re: Hohner Morino Club
« Reply #25 on: September 30, 2022, 04:38:28 PM »


This tech info is greatly appreciated. It clarifies the function of the "special box" which I will replicate. I will check further on what the phono jack connects to.

Dates of manufacture for Hohner Morino Club "S" from 1987 to 2006
per Hohner website.
Logged

mayord21

  • Good talker
  • **
  • Offline Offline
  • Posts: 58
Re: Hohner Morino Club
« Reply #26 on: October 17, 2022, 03:17:44 AM »

Update on midi discussion for morino.  I have now completed midi box _ picture attached.

 It works great with the V3control module (chord ch2 bass ch3 treble ch1). It seems very responsive to bellows direction change and always sends correct midi note. Volume does not change with bellows pressure. I would like to know how it is determining bellows direction (pressure transducer?)
Logged

JD

  • Regular debater
  • ***
  • Online Online
  • Posts: 235
Re: Hohner Morino Club
« Reply #27 on: October 24, 2022, 09:37:04 AM »

Congratulations on making this work. Imagine how much Hohner would charge for an interface box with just a few wires inside!


It might be worth using a MIDI logging program to check for "expression" values. A value from the pressure sensor might be sent as expression rather than volume. This is used to simulate a swell pedal on some synths. Whether your V3 module could use it is another question.


As for the pressure sensor, is it the component that looks like a microphone mounted on one of the blocks? I always thought that a MIDI accordion would use two pressure sensors,  one inside the bellows and one outside. I know the Streb only uses one.
Logged

howard mitchell

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 456
    • Howard Mitchell
Re: Hohner Morino Club
« Reply #28 on: October 24, 2022, 12:02:16 PM »

I’m guessing here-

The circuitry at the left of the board looks like something linear, maybe an A to D. There are 2 red preset pots, possibly gain and offset. If the gain is set high the bellows pressure would appear on or off as you report.

Is there a pressure sensor something like one of these somewhere https://datasheet.octopart.com/MPX5010DP-Freescale-Semiconductor-datasheet-98060.pdf

The round object mounted on a rubber suspension attached to the block is an internal microphone.

If you could send a pic of the numbers on the chips on the left it might be possible to work out more.
Logged
Saltarelle D/G, Hohner D/G, Hohner C/F, Dallape C/F, Hohner A/D, Gaillard G/C, Sagne D, Roland FR18D, Hohner Bb/Eb.
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal