Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner GCF repair  (Read 1600 times)

0 Members and 1 Guest are viewing this topic.

Carlos

  • Member
  • *
  • Offline Offline
  • Posts: 16
Hohner GCF repair
« on: May 20, 2021, 07:48:03 PM »

So long story short I was putting the grill back on my german hohner GCF and went i lightly tapped the pin in and after I got it in half way and then gave up, I continued playing and noticed it was out of tune on a few notes.  What should be done about it? The reed must not be the best if a few small taps knocked it out of tune. It needs repairs to begin with.
Logged

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Re: Hohner GCF repair
« Reply #1 on: May 20, 2021, 09:49:24 PM »

What type / age of instrument is it?  From what I gather, the newer Hohners that are made in China are pretty notorious for having tuning issues right from the factory.  The reeds are fine, they're just not always fine-tuned.  My guess is, it's not likely to be your tapping that did it, unless you somehow happened to knock valves loose.
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner GCF repair
« Reply #2 on: May 20, 2021, 10:04:00 PM »

What type / age of instrument is it?  From what I gather, the newer Hohners that are made in China are pretty notorious for having tuning issues right from the factory.
This was also true for German Hohners as well

Carlos

  • Member
  • *
  • Offline Offline
  • Posts: 16
Re: Hohner GCF repair
« Reply #3 on: May 20, 2021, 10:18:44 PM »

The notes i knocked out of tune sounded fine just before i starting trying to put the grill back on. I took the grill off becuase it is slightly warped and stopping some bottons from being pushed down all the way. I dont know to post pictures on here.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner GCF repair
« Reply #4 on: May 20, 2021, 10:34:06 PM »

If it is a very old instrument the wax holding the reeds may be weak.  Some reeds may have worked loose.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: Hohner GCF repair
« Reply #5 on: May 21, 2021, 08:30:42 AM »

Old German GCF? Pins wont go back in? Yup sounds like dodgy wax and maybe a sign that its time for a service. Can also be loose valves. The glue holding them on can get old and brittle. Such things are usually a sign that its time to delve inside and assess the situation. Pins are an easy fix. New ones can be obtained or clean up the old ones. If you look inside its usually possible to see if its loose or brittle old wax. Loose or damaged valves on the push notes also can be easily spotted. On the pull notes you can check by carefully taking out the reed blocks.   
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner GCF repair
« Reply #6 on: May 21, 2021, 08:49:26 AM »

A quick and easy way to check wax condition is to scratch the wax with a fingernail.  If the scratch looks light coloured and powdery the wax is perished and needs to be replaced.  While the reeds are out you also clean them thoroughly and replace *all* the valves.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Hohner GCF repair
« Reply #7 on: May 22, 2021, 07:17:15 PM »

Old Hohners can be weird with the wax, even if it is soft it may have pulled away from the reed plate and will no longer have holding power.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

tirpous

  • Hero Member
  • *****
  • Online Online
  • Posts: 1403
Re: Hohner GCF repair
« Reply #8 on: May 22, 2021, 09:41:08 PM »

Quote
So long story short I was putting the grill back on my german hohner GCF and went i lightly tapped the pin in and ...

They may look like nails but it's probably better/safer to -press- the pins in place if possible, could be with a hammer face, side of pliers, etc...  Avoids loosening up stuff.

 

Logged

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Hohner GCF repair
« Reply #9 on: May 23, 2021, 09:02:32 AM »

We are talking grill pins. You need to pull the bellows pins at the treble end now and look inside. The wax may be breaking down but also as likely and an easier fix the blocks may have moved. Check the small wood blocks are there.This is all relatively easy.If the wax is brittle then its a rewax not so easy.There are quick fixes just repair the loose reed or overwax but these are temporary and advised against.You may have a rattle when you shake the box but be gentle.
Logged
Mark Taylor
Folkloristmark

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Hohner GCF repair
« Reply #10 on: May 23, 2021, 10:38:32 AM »

Quote
So long story short I was putting the grill back on my german hohner GCF and went i lightly tapped the pin in and ...

They may look like nails but it's probably better/safer to -press- the pins in place if possible, could be with a hammer face, side of pliers, etc...  Avoids loosening up stuff.

Yes, also it's a good idea to make sure pins go back into the hole they came out of. Small variations in diameter make a big difference.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner GCF repair
« Reply #11 on: May 23, 2021, 10:51:54 AM »

And if the pins are rusty they should not be replaced.   Rust is abrasive and will enlarge the holes.  Replace with new pins and they will push in easily.  Rusty pins belong in the bin.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Hohner GCF repair
« Reply #12 on: May 23, 2021, 02:09:58 PM »

Just to clear up an ambiguity, I believe the meaning of Theo's remark was that rusty pins should not be re-used.

Rob
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner GCF repair
« Reply #13 on: May 23, 2021, 02:21:59 PM »

Thanks Rob, I didn’t explain that very well.

To clarify

Rusty bellows pins should be discarded and new ones fitted instead.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Carlos

  • Member
  • *
  • Offline Offline
  • Posts: 16
Re: Hohner GCF repair
« Reply #14 on: May 25, 2021, 02:17:49 PM »

I tried to pull the pins out but they only moved a small bit they are rusty. Something is rattling around inside. It looks like a corona model but it isnt. A couple bass notes have buzzing. Im going make a video of how it sounds and post it later.
Logged

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Re: Hohner GCF repair
« Reply #15 on: May 25, 2021, 02:29:10 PM »

Is it one of the "pre-corona" models, usually black, with some decorative elements on the fingerboard?

If you have rattling, reeds are certainly loose.  Best to be ginger when playing it - the reedplates can fall into the bellows folds and cause tears when the instrument is closed.

If you have an old pair of pliers or nippers, and a rotary tool with a spherical-tip bit approximately the size of the bellows pin head, you can fashion a bellows pin pulling tool that will make the job of pulling the pins a lot easier.
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Hohner GCF repair
« Reply #16 on: May 25, 2021, 03:46:18 PM »

Assuming you are going to replace the pins anyway, I'd grab the pin with good grippy pliers laid flat and with card of a few sheets of paper underneath to protect the surface. Then work backwards and forwards twisting the pins until they feel a little looser. Then a wriggly straight pull should get your pins out. The pin heads will look a mess now and the bin will be the best place to file them.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Hohner GCF repair
« Reply #17 on: May 25, 2021, 09:25:45 PM »

If you have a soldering iron put it on the pin for a longish time to expand the metal, then let it cool down.
It might make the job easier, ............ then again ...............
Mole-grips are better than pliers for the job. I have a mole-grip on my bench specifically for rusty pins.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal