Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Old reeds  (Read 1257 times)

0 Members and 1 Guest are viewing this topic.

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Old reeds
« on: May 29, 2021, 12:06:47 PM »

I promised to take pictures of rusty reeds Theo .... in these a lot of rust, I do not know,, can restore them ?? I think G / C
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Old reeds
« Reply #1 on: May 29, 2021, 12:20:57 PM »

I would expect them to clean up fine.

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: Old reeds
« Reply #2 on: May 29, 2021, 12:24:20 PM »

Yes .. Theo promised to tell me how I can remove the rust,
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Old reeds
« Reply #3 on: May 29, 2021, 12:33:59 PM »

Yes they should be fine once cleaned.
Tools I use:
Support plate same as used for tuning
Polishing block - coarse https://www.amazon.co.uk/Garryson-Garryflex-Abrasive-Block-120grit/dp/B0001P08UQ
Small screwdrivers

For the top surface support the reed tongue and rub with the polishing block.  This will remove most rust but doesn’t remove any significant amount of steel.  Any coarse lumps of rust that resist the polishing block might need to be scraped with a screwdriver or something else with a hard edge. I prefer not to use a file because it’s too easy to remove steel as well as rust.

For the underside place the reed plate on a flat smooth surface and scrape with a small screwdriver.  You can get quite cheap sets of “jewellers screwdrivers” which are fine fir this.
Finally I’d give each side of the plate a light rub with a soft wire brush to remove any loose debris.

Important: when using any of these methods always work away from the rivet and toward the free end of the reed.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Old reeds
« Reply #4 on: May 29, 2021, 12:34:50 PM »

Yes .. Theo promised to tell me how I can remove the rust,
I would use these to clean the top of the reeds whilst supporting the tongue with a pinger. Any rust on the inside of the reeds can normally be scraped off with a screwdriver blade. I would then go over the reed plates with a brass brush.


Edit; Same as Theo then  (:)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Old reeds
« Reply #5 on: May 29, 2021, 12:40:37 PM »

Though with a different grade of polishing block!
I do have 3 grades but for the degree of rust in the photos I think the coarse would be most effective.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Old reeds
« Reply #6 on: May 29, 2021, 12:57:38 PM »

Being non(un)professional, I've used a rust removing fluid with great success. It's called Evaporust and it's very easy to use and is even safely disposable! I got it off eBay, where it was cheap enough for even me to buy it!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: Old reeds
« Reply #7 on: May 29, 2021, 01:41:39 PM »

Thanks everyone, I try to find the right tools for myself (:)
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: Old reeds
« Reply #8 on: May 29, 2021, 03:44:59 PM »

most folks seem to use acetone to clean off all the crud (old wax and glue and nicotine ). comes off nice with a soak and a cotton bud and eyebrow cotton buds for the smaller reeds. I use a two bath process. first one to take out the hardcore stuff. then into second bath for a cleaner clean. For those reeds I'd go acetone first so i get rid off all the crud. Then the gentle scraping and abrasive block or flexfile mini sanding sticks. Then more acetone to clean off again. Obviously tuning will be needed after removing rust and putting on new valves. I cleaned some recently and on some reeds the rust was worse at the rivet end and they were all 50 cents flat after removing rust.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Old reeds
« Reply #9 on: May 29, 2021, 06:29:24 PM »

I used a piece of medium fine Emory cloth tape to clean the underside of reed (part way)  by slipping a piece of Emory cloth in under the reed as you would a pinger and pulled back the Emory cloth towards the tip of reed once or twice , then scraped close to the rivet with a screwdriver.  Probably frowned upon but it worked well on the beat up hohner I was fixing. I was careful to keep the Emory cloth flat and no pressure was applied or at least not much so that I didn’t remove rust from the edge and not the middle, which I assume would be the reason for not doing it this way.
No detectable reed material was removed other than surface rust.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal