Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Single Reed Replacement - Brass reeds on Zinc plates  (Read 4148 times)

0 Members and 1 Guest are viewing this topic.

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Single Reed Replacement - Brass reeds on Zinc plates
« on: June 24, 2021, 04:20:33 PM »

I have been working on replacing a couple of broken reeds this morning and I thought I would post a few pictures.

This is the best way I have found to replace old brass reeds to date.  Any advice on better methods would be much appreciated.

I am working on Hohner brass reeds circa 1920 (H brass on Zinc) and using scavenged brass reeds as replacements. I want to replace like for like in terms of reed material if at all possible (finding complete replacement plates is/was almost impossible).

So my method is:

Scavenge same era reeds at same or near size (source at close/lower frequency).
Grind off rivet heads and drift on target plate and remove broken reed
File reed to suit aperture (time consuming)
Bolt using 1.4 mm
Tune by filing back the reed tip (I found trying to thin the reed at the tip ruined the reed quality - best to keep integrity of reed in terms of thickness)
Fit brass strip to create new leading edge
Final tune

I attach some photos of final result.

Are there any other better ways/tips?  I have not tried riveting yet as it seem a bit final.

Single Reed Replacement - Bolted Reed by John Burks, on Flickr

Single Reed Replacement - Bolted Reed by John Burks, on Flickr

Single Reed Replacement - Leading edge by John Burks, on Flickr


« Last Edit: June 24, 2021, 04:22:23 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #1 on: June 24, 2021, 05:57:27 PM »

John-
Nice work. I explain the process I used in this video. The video link starts at the point I discuss it. I also bolted mine in place instead of riveting and it worked fine. I was able to locate a donor piano reed from another longplate piano accordion.

https://youtu.be/Wpj3gNohcRc?t=79

Scott
Logged
too many boxes...please buy one, or two, or

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #2 on: June 25, 2021, 09:51:03 AM »

Thanks Scott, I really enjoyed the video. I see you tapped the plate and then used a locknut which is better. Thanks. I will try this on the next one.

This was the first time of working on a single plate with two reeds and I simply used a nut and bolt through the original rivet hole with a bit of “locktite”.  V small taps and miniature bolts now on order though 😊

I also enjoyed the section on tuning ….. I am preparing a spreadsheet for mapping.

It’s a beautiful old box so I want to do it justice.  To bring something back to life is a joy.

Thanks
John
« Last Edit: June 25, 2021, 09:55:46 AM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #3 on: June 25, 2021, 09:37:20 PM »

Why kind of grinder did you used? A handheld or a table grinding wheel?

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #4 on: June 26, 2021, 08:24:24 AM »

Why kind of grinder did you used? A handheld or a table grinding wheel?

Handheld “dremel” using a rounded cone stone (or spherical) approx 1/4inch under a large magnifying glass. Plate held horizontally in drill press vice on bench. If you place the wheel on the head of the rivet it will take it down leaving a ring of swarfe (hopefully). This exposes the junction between plate and rivet as a faint circle.  Then use sharp punch.  Take off broken reed on other side in similar way first though. This relieves interference.
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #5 on: June 26, 2021, 08:55:58 AM »

I might have used a tiny bit of polystyrene cement applied with a cocktail stick rather than loctite - it forms a bond strong enough to hold something from working loose by itself but easily broken - I mainly use it prevent sidehook closures from releasing themselves at inopportune moments.
Logged

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #6 on: June 26, 2021, 10:24:25 AM »

I might have used a tiny bit of polystyrene cement applied with a cocktail stick rather than loctite - it forms a bond strong enough to hold something from working loose by itself but easily broken - I mainly use it prevent sidehook closures from releasing themselves at inopportune moments.

I hear where you are coming from and totally agree. Good idea and I will try. Thanks.

At the moment I only apply a little dab of locktite on the bolt/ nut interface away from the plate so things are completely reversible. To change you simply grind off the faceted bolt head on the reed end. The plate remains completely clean. The only compromise I make is re the brass strip where I use Hohner valve glue which I hope will allow easy removal and cleaning.  I will give polystyrene cement a go though as an alternative. I will also try a bit under a reed and see how it fares as I worry that the reed might shift over time.  The nut and bolt should hold but the reed could rotate. Thanks for thought/idea.

The key thing for me is not to move away from the original as much as possible  …. but at the same time I do want that reed to sing ….. struggling to find the best way in terms of conscience  😳
« Last Edit: June 26, 2021, 10:34:28 AM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #7 on: June 26, 2021, 11:04:05 AM »



The key thing for me is not to move away from the original as much as possible  …. but at the same time I do want that reed to sing ….. struggling to find the best way in terms of conscience  😳

Same issue for me - If I restore a box I don't usually want to modernise it.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #8 on: June 26, 2021, 12:13:03 PM »

In this situation I usually use a file to remove the rivet head.  Work from the reed side the remains of the old reed protects the plate from file marks. Rivets are always made of fairly soft metal, even if made of steel, so easy to file.
With a little practice you can learn to set a rivet.  You do t need a rivet with a pre-firmed head. Just a length of mild steel/soft iron, round nails are a good source of material.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #9 on: June 26, 2021, 12:46:18 PM »

"Just a length of mild steel/soft iron, round nails are a good source of material."

Also easier and cheaper to source, whilst keeping closer to originality I would have thought.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #10 on: June 26, 2021, 03:44:17 PM »

"Just a length of mild steel/soft iron, round nails are a good source of material."

Also easier and cheaper to source, whilst keeping closer to originality I would have thought.

So true.  Thanks both for input. I must admit that I started out with the intention of riveting but erred away from it probably out of ease of fitting (not that this should be an excuse).  One of the main issues I came across was the need to foreshorten the reed length to get the increased frequency. Thinning the tips just left me with a feeble and very unstable reed ( it just lacked depth of tone). I know the problem is the donor reed’s modulus of elasticity/thickness not being matched but I was stuck with what I could get. So in as much as I was compromising the original design re the reed length I went the whole hog and bolted. What it also did to is allow a better fitting process as you can bolt and get lateral adjustment of the reed gaps. You can also turn the reed to aid foreshortening (filing with Emery boards). This leaves the original plate completely unsullied in my mind, apart from the glue!  The box is going nowhere except with me so I must admit the idea that I can adjust/change reed material on plates at will also appeals (as per some concertinas with reed clamps).

That said ….. Once the reed is set though there is absolutely no reason why a rivet cannot be fitted. So I might try one.

I will have to pull out my peening hammer and blocks 😉

Thanks for continuing the thread …. All views welcome.   I just think it’s good to discuss techniques like this as there are a lot of broken reeds out there ( I suspect).👍
« Last Edit: June 26, 2021, 04:15:45 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #11 on: June 26, 2021, 10:50:51 PM »

Although I've replaced a few single reeds, and foreshortened a few as well; cowboy that I am, I more usually just change the reedplate for one of the many I have in stock, saved from scrapping things. It's much easier!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #12 on: June 26, 2021, 11:24:48 PM »

Although I've replaced a few single reeds, and foreshortened a few as well; cowboy that I am, I more usually just change the reedplate for one of the many I have in stock, saved from scrapping things. It's much easier!

😄 My problem is minimal stock 😳
« Last Edit: June 26, 2021, 11:28:52 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #13 on: June 27, 2021, 04:17:47 AM »

I sometimes use hard aluminum aircraft rivets. They are self hardening and need to be annealed before using. You can do this by marking them with a sharpie and heating them till the marks start to fade. Let them cool and they will be ductile for a few days and become quite hard in a week.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #14 on: June 27, 2021, 07:19:37 AM »

Somewhere on YT there is a Spanish language vid of a reed being fashioned from some spring steel and where the rivet is made from old PA bass machine parts...I.e. a push rod of suitable diameter. It’s soft enough to make a rivet. I did try to make a reed once but it was an abject failure. It’s something I really ought to persevere with, so I take off my (metaphorical) hat to all you chaps who can do it.
Also..Carini do stock a range of reed rivets.
« Last Edit: June 27, 2021, 07:22:17 AM by RogerT »
Logged

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #15 on: July 02, 2021, 04:47:21 PM »

Thanks for advice re rivets.  I will experiment a bit and see what works best. I need to source or make some punches.

I filed and fitted the final tapered reeds today (bass chords) and thought I would take a minute to post. 

The process was:

Remove broken reed (grind and punch)
Source, remove and prepare donor reed (similar flexibility/ thickness)
Bolt replacement to reed plate (bolt dia.  to fit rivet hole/reed)
Align on center line and mark outline using a very sharp scalpel through the aperture (I am marking brass remember so it gives a very sharp outline. Not sure about steel)
Remove reed for filing
Clamp providing a straight edge on the marked line covering desired reed mass.  I used a very old hand vice which worked a treat (see photo).
File down using emery boards (much better than using a traditional file). Much more control.  File across the edge. File both sides roughly to the marked lines and then remove trial fit to plate aperture, re-clamp, file , repeat.
When filed to suit re-fit reed to plate over aperture using bolt.
File length to fit and adjust overall fit using backlight. (you can rotate the reed which helps  lot) (see photo)
Once the fit is perfect then tighten bolt down
Tune to target frequency by traditional reed thickness reduction or foreshortening/replacement of leading edge.
Finally lock bolt and install valves

It works a treat.  Each reed took about an hour.

Here are some photos:

Hand Vice - Tapered Reed Filing by John Burks, on Flickr

Hand Vice - Tapered Reed Filing by John Burks, on Flickr

Tapered Reed Fit (on right) by John Burks, on Flickr

The reason for posting is to share and to show how easy it is to do.  The old box I am repairing has seen a lot of work.  It is a really old M Hohner in B/E but it beautifully aged and it has a beautiful beautiful tone.   The reeds are really good quality brass.  Today I finished the bass reeds and chords.

It took me the whole morning to tune the chords but ....... it was worth it just to hear the richness of tone! What a joy!

Its a pain really to replace reeds but hey ho I think its worth it!  Nothing wrong with brass reeds!

Now I have to cure the leaks  ::)
« Last Edit: July 02, 2021, 05:06:34 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #16 on: July 02, 2021, 09:08:23 PM »

I have an old concertina with long reed plates, and one reed is broken. So it either needs a replacement plate, unlikely, or the brass reed replacing, but it's not something I would tackle.

Sir John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #17 on: July 03, 2021, 12:14:15 PM »

I did try to make a reed once but it was an abject failure.

I'm amazed any one person ever succeeds as there are so many variables, not just of craftsmanship, but material selection and matching tone, etc.  I've really enjoyed reading the thread, though this was what struck me the most that the amateur or one-man worker will most probably always have to start with a donor reed from the correct type and era of box.  It brought back a seemingly insignificant chat with Ivor Hyde about the mountain of scrap accordions in his workshop.  He admitted that he had to be ruthless from time to time and clear them out, yet they were the saviours of many a box and once gone future repairs would become nigh on impossible, or at least no longer cost effective.

I was also delighted to see that the techniques used in Harmonica repair are being applied to our scaled up versions!

Rob.
Logged

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #18 on: July 04, 2021, 01:16:42 PM »

I did try to make a reed once but it was an abject failure.

I'm amazed any one person ever succeeds as there are so many variables, not just of craftsmanship, but material selection and matching tone, etc.  I've really enjoyed reading the thread, though this was what struck me the most that the amateur or one-man worker will most probably always have to start with a donor reed from the correct type and era of box. 

So true.  Using the same era reed is really important not only in terms of tone but also in trying to match the reed profile.  As I got into the process I started to realize how finely the reeds were finished.  You have to admire the workmanship.  The brass Hohner reeds from early last century had been pretty much perfected.  Square on low notes and transitioning to tapered mid range to high.  The reed profile in terms of thickness was also pretty much perfect with variable thickness down its length.  They balanced reed integrity and overall tone.  So what you have to replace is a highly optimised reed in a matched aperture.  The aperture actually reflects the maximum possibility of the base material.
So its a bit of a stretch to come along and replace like for like even if you get the right material.

Initially I tried to thin a reed using donor material to suit the profile. Pretty much impossible without a belt sander.  You end up with very thin sounding reeds even if you sand very carefully (I used a rotary wheel).  I could not duplicate the original workmanship.  This then made me think about the dynamics of the reed.  Its a free asymmetric reed so it essentially acts like a cantilever and the key parameters are elasticity (Youngs modulus), thickness and length. Width does not matter as much and anyway it's a given considering the existing aperture which you cant really alter.  So all you can play with when replacing is thickness and length.  As I say thickness is a pain to achieve.  Length though you can adjust. Soo the best thing is to source a reed of the same material with a reed profile (thickness) (variable) that helps overall tonality that has enough leeway for achieving the final desired note frequency.  So I selected a same era reed that suited the fit in relation to the aperture that I knew would allow adjustment to length to increase frequency.  I wanted to increase frequency by starting with a lower frequency reed and taking off the tip rather than starting with a higher frequency reed and filing the base of the reed (which I had tried and failed). I had also tried thinning the tip but this just destroyed tonality.

So I went for a lower frequency reed and I took the tip off the reed to tune and created a new leading edge. This way you get a shorter less optimized reed but at least you have the leeway you need for tuning without thinning.  Tuning by filing the tip with an emery board is really accurate and does no damage to the reed. Also I found that a simple twang of the reed with a scalpel blade with my Peterson app running allowed me to tune pretty close or at least close enough for a first fit (I.e. no need to have the leading edge in place)

The only problem with this foreshortening method though is the leading edge.  You don't have the plate depth. The reed therefore vents more quickly at the end of the down stroke and this does effect the pressure wave, but in my mind at least the reed is vibrating at its base frequency albiet as a slightly lower volume so what the heck.  I have a sounding reed at perfect pitch.  What I will try eventually though is making up the reed plate depth in the aperture depth by using some sort of filler.

Better replacing with slightly less optimized brass reed than a later era steel reed on a new plate  ;)

John

« Last Edit: July 04, 2021, 02:30:34 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #19 on: July 04, 2021, 01:26:21 PM »

I have an old concertina with long reed plates, and one reed is broken. So it either needs a replacement plate, unlikely, or the brass reed replacing, but it's not something I would tackle.

Sir John

Actually the long reed plates are usually pretty easy to work on.  The first reed I replaced was on a long plate.  It was an Anglo (Kalbe) and found that the reed plates on many of these cheaper concertinas (and accordions) used the same reed stock.  the long plates also had the same reed pitch.  So I was able to find a direct replacement.  Same frequency and fit.    Worth a try.  I will post a picture later.

John
« Last Edit: July 04, 2021, 01:58:25 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal