Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Single Reed Replacement - Brass reeds on Zinc plates  (Read 4152 times)

0 Members and 1 Guest are viewing this topic.

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #20 on: July 04, 2021, 02:03:40 PM »

All quite  and kind of pulls together unresolved details in many Youtube videos!  Two come immediately to mind.  The first was an "old hand" riveting a reed by hand.  The whole process involved repeated checks of fit and alignment, constantly checking that the rivet head was fully home and the reed itself aligned.  He bent the reed through an amazing arc to access the sides to relieve for a very close fit in the aperture.  The second may have been a later part of the first (memory isn't that sharp any more!).  Once fitted, the reed was profiled and tuned using a long, narrow belt sander across the reed.  Of course the amazing thing is that all these operations were being done manually, at high speed with the skill to produce both the desired tone and pitch!

I'm amazed that a reedset would go from square bass reeds to tapered section treble reeds.  It just go to show how thorough our forebears were in developing these instruments - so many variables...

Rob.
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #21 on: July 04, 2021, 02:50:51 PM »

I have an old concertina with long reed plates, and one reed is broken. So it either needs a replacement plate, unlikely, or the brass reed replacing, but it's not something I would tackle.

Sir John

Actually the long reed plates are usually pretty easy to work on.  The first reed I replaced was on a long plate.  It was an Anglo (Kalbe) and found that the reed plates on many of these cheaper concertinas (and accordions) used the same reed stock.  the long plates also had the same reed pitch.  So I was able to find a direct replacement.  Same frequency and fit.    Worth a try.  I will post a picture later.

John
That's good news. I have a long plate box that needs a new reed.
Logged

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #22 on: July 04, 2021, 05:08:12 PM »

Sir John

Here are a couple of pictures.  Hope it helps.  The long plates always have parallel sided apertures which makes things a lot easier. I wanted to replace a reed in an old Anglo concertina (10 reeds) and took a reed from a long accordion plate (20 reeds). The Concertina is probably Kalbe and from memory the donor reed bank came from a Kalbe accordion (same era though and same quality).  The reeds are quite robust in these units.  I simply looked for the same frequency and found it.  It fitted well.

I drilled out the old rivet on this one (not so good - better to grind), sealed the hole (UV resin), drilled at other end and reversed the reed. I bolted as usual. Locked with UV resin.

Its worth a try.  For me its best to have a go.  I felt that I could not loose really. The concertina didn't play anyway.

Bolts I use are on Amazon.  Search for "600pcs Small Screws Nuts Assortment Kit Repair Tool Nut & Bolt Assortment M1 M1.2 M1.4 M1.6" and you should find them. I use the longest M1.4.

It was a bit of a rough repair (first one) but it now plays quite well.

John

Concertina by John Burks, on Flickr

UV Resin Locked by John Burks, on Flickr

Reverse Bolting by John Burks, on Flickr

« Last Edit: July 04, 2021, 05:12:22 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Single Reed Replacement - Brass reeds on Zinc plates
« Reply #23 on: July 04, 2021, 06:51:11 PM »

Grand job. It's still something I'd rather pay someone else to do. I'm a woodworker, and not a metalworker. So I stick to what I can do, and let others do what I can't.

Sir John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal