Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reeds go off pitch: Why? and do they always/usually go flat?  (Read 3011 times)

0 Members and 1 Guest are viewing this topic.

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039

I have only ever re-tuned the odd replacement reed- so I don't have a clue as to what direction reeds that drift off go. I would expect steel reeds to flatten mainly due to rust eroding the middle of the reed - but I may be completely mistaken.

Are brass / bronze reeds less prone to pitch drift?

Thanks All,

P
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #1 on: July 19, 2021, 12:38:15 PM »

Rust near the tip lowers the pitch too, as does a buildup of airborne dirt. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Mike Hirst

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1433
  • Black Dot B/C, Bastardo C#/D, Corona II GCF
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #2 on: July 19, 2021, 01:24:21 PM »

As a musician, not a mender, my experience of out of tune reeds is usually related to a fracture of the metal in the reed. I have always used cheap/basic accordions, which I tend to play fairly hard. On the one row I tend to overwork the flat seven. It's always this note that goes out of tune. Experience has shown that a good hard yank (away from the mic) will open the fracture and take the offending reed out of play.

On one memorable gig, playing in Leeds, with what was at the time a psychedelic country folk outfit, i heard the Mixolydian flat seven (F) on the C row start to slip. I continued the extended solo, that was the culmination of the show, avoiding the out of tune reed. 

At this point we had strobe lights hitting the mirror ball, guitar was cranked up to 11 and the drummer was beating the skins louder than the Scots Guards at Edinburgh tattoo. At the culmination of the show I hit the F, pulling hard and slow on the bellows. The broken reed slipped slowly lower. falling through two, maybe three octaves. As the note fell the dissonance with the remaining (in tune) reed become wider. At a certain point there was a visible shudder ran down the spine of every person in that room. The consensus view of all who were there on that night was that we had all walked with gods.

A simple trick, but very effective.
Logged
Semper idem, sed non eodem modo

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #3 on: July 19, 2021, 01:36:04 PM »

Reeds can go slightly flat without being in danger of breaking. Slight bending as when adjusting gaps often sends the pitch flat by a few cents, but I’ve not seen that make them sharpen.  Valve behaviour changes pitch too which is why you should always deal with any valve problems before tuning.  New leather valves can become more flexible with play which can make reeds sound slight sharp.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #4 on: July 19, 2021, 05:35:59 PM »

The ones that get used a lot sometimes shift pitch. Leaving aside specific issues, where one reed goes off, I’ve seen modern PAs with a slight upwards movement from concert (assuming the tuning was good in the first place) up to 5 or a bit more cents, on the reeds around and above C5. Less used accidentals seem not to do this so I associate it with heavy use. I don’t know why. It does often seem to be slightly sharp rather than flat, but that doesn’t mean they don’t go the other way.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #5 on: July 19, 2021, 05:39:30 PM »

Roger that all presupposes that it was previously tuned to 440. I’ve seen a lot of piano boxes that are tuned to 441 or 442, so the +5 cents could be the original tuning and the lower reeds have flattened.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #6 on: July 19, 2021, 10:59:19 PM »

Roger that all presupposes that it was previously tuned to 440. I’ve seen a lot of piano boxes that are tuned to 441 or 442, so the +5 cents could be the original tuning and the lower reeds have flattened.
Well, when i said concert I should have been a bit clearer....I meant the reference pitch, whatever that is. Obviously I establish the ref tuning first...(I don’t just set my tuner to 440... (:)).

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #7 on: July 21, 2021, 08:46:39 PM »

Any comments on brass reed drift?
Generally less prone to corrosion than steel reeds - but presumably just as easily affected by condensed nicotine etc, though on older Vienna boxes a lot of this seems to have been stopped by the grille cloth...while on the German types the metal plated pallet backs sometimes look suspiciously brown...

Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #8 on: July 22, 2021, 02:38:38 AM »

The only experience I have of brass reeds was on a Wheatstone Student model English concertina.  I tuned a few "howlers" back to pitch, but within a month they had wandered off again.  I wonder whether in my naive way I had failed to set a realistic and sustainable tip gap.  The other issue is that whilst often used as spring contacts in electrical equipment, brass doesn't have the resilience of a steel spring metal and is more prone to work hardening...

Used in the same way as a steel reed box (balancing with other instruments), I concluded that the reeds were not as stable - though they may be much longer lived if only played at a more moderate volume.

Rob.
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #9 on: July 31, 2021, 05:52:12 AM »

I found that brass reed have the unfortunate habit of the high reeds going flat and the low reeds going sharp. This sounds really bad.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #10 on: August 01, 2021, 01:23:23 PM »

The only experience I have of brass reeds was on a Wheatstone Student model English concertina.  I tuned a few "howlers" back to pitch, but within a month they had wandered off again.  I wonder whether in my naive way I had failed to set a realistic and sustainable tip gap.
Much more likely that the cause of the original flattening continued after your tuning.   Incorrect reed gap can have a very small effect on pitch, but I wouldn't expect it to lead to continuing changes.


Quote
  The other issue is that whilst often used as spring contacts in electrical equipment, brass doesn't have the resilience of a steel spring metal and is more prone to work hardening...

We all talk glibly about "brass" as if it were a single material, but really it is a very varied family of alloys with differing physical properties, many of which can be further modified by cold working and by heat treatment. For example I've worked on two Wheatstone Aeolas with brass copper alloy reed tongues.  They are as loud as steel reeds, and one has been played hard by a friend for decades with only minimal changes in pitch.  I suspect that the material may be phosphor bonze.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #11 on: August 01, 2021, 02:36:57 PM »

I think you're right, Theo.  I'd expect nothing less in an Aeola, but my student model is definitely built down to a price!  It has a soft, mellow tone and not too much volume - it'd be great for song accompaniment if the tuning were more stable.

On ather arenas in whic I have an interest (boats) I was wondering whether I should make a false advertising complaint.  A manufacturer of forged DZR ( corrosion resistant) brass seacocks stated they were using the best possible materials, yet bronze is far more resistant to zinc loss...  It reminded me of the labels that were attached to brass reeded instruments saying they had "steel bronze" reeds.  Sorry, just rambling.

Rob.
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #12 on: August 02, 2021, 06:27:14 PM »

Revisiting Copper alloys.
Brass is a Copper/Zinc Alloy. 60/40 i.e. 60% copper 40% zinc is commonly used and cuts easily.
Bronze is a Copper/Tin alloy.  "Steel Bronze" is a (cold?) forged 92% copper 8% alloy. I haven't got access to historical metallurgical texts that might verify whether this was a standard engineering term in the early 1900s.
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #13 on: August 12, 2021, 05:04:03 PM »

When I was doing some boat work I did a little research into bronze. There are a LOT of different bronzes. They seem to contain just about every metal, aluminum is popular for marine work.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #14 on: August 12, 2021, 07:56:44 PM »

When I was doing some boat work I did a little research into bronze. There are a LOT of different bronzes. They seem to contain just about every metal, aluminum is popular for marine work.
There might be a difference between British and American English - In England Brass is very specifically a copper-zinc alloy and bronze a copper-tin alloy.
There has been a huge development in alloying techniques since....1940 probably - but even when I was an undergraduate (Early 1980's this was pretty cutting edge when it came to industrial useage. Not least because mild steel was an order of magnitude cheaper than any copper alloy. )
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #15 on: August 12, 2021, 09:05:18 PM »

...bell metal is a bronze alloy, but with a higher tin content (around 20%).

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #16 on: August 12, 2021, 11:10:17 PM »

Thanks Paedar for the "Steel Bronze" alloy details.  I suspect it to be a far superior choice than the brass in my old concertina, but among melodeon makers I think the prominent label stating the reeds to be Steel Bronze was a fop to those who really wanted steel reeds, but could not afford those higher spec models that had them.

I suppose that when messing around boats and the sea (salt laden atmosphere) those steel bronze reeds would be well suited.

Rob.
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Reeds go off pitch: Why? and do they always/usually go flat?
« Reply #17 on: August 13, 2021, 08:39:00 AM »

There is the possibility that pre-1914 "Steel Bronze" was being used as a trade term for "hard brass". The answer is probably to be found in one of the textbooks published by Gresham or Spon.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal