Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Braces across reed blocks: Why?  (Read 1341 times)

0 Members and 1 Guest are viewing this topic.

Jack Humphreys

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • tunesbyjackhumphreys
Braces across reed blocks: Why?
« on: October 10, 2021, 01:08:27 PM »

This is about the strip of metal screwed across the top of several reed-blocks, presumably to stabilise them. I've also seen short bits of wire (like paper-clip wire) jammed between one block and other, presumably for the same purpose. But Ive heard different stories about why:

Tuner A removed the brace and taped it to the inside of my case. He said that braces kill the soul of the instrument,  which would sound more alive without. John Spiers was quoted as sharing this view.

(I nevertheless replaced it, out of respect for the maker's expertise)

Then Tuner B told me that the purpose of the brace was to help maintain the correct tremolo, and stop the reeds getting entrained....pulled towards unison.  However, my box was now tuned unison, without tremolo, so I didn't really need the brace. He nevertheless preferred to replace it.

Then I did some experiments at home.  I found that without the braces in MM, each note began with a tiny odd glitchy sound before settling to unison. The effect was slightly uncomfortable, spoiling the intended unison.
Replacing the brace got rid of these odd sounds.  So it's going to stay!

In case it's relevant, these are the Binci reeds on my Guais, which turned out to be too unstable (according to both tuners) to accept being tuned to a mild swing.

So I wondered what is the accepted purpose of the brace and its upsides and downsides.

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Braces across reed blocks: Why?
« Reply #1 on: October 10, 2021, 01:39:28 PM »

Had this conversation with Frans van der Aa, who is also a pretty good player. He is firmly of the opinion that the metal coupler is important to tone, though we didn’t discuss the ‘attack” dynamic you mention.

He metal strap couples MM’s, and also across to the L blocks. I am pretty sure myself that my low L notes come in with a lag, cool about that as it’s fine with song. Playing a tune I usually couple in my M bandoneon, ie true, reed set. It definitely improves the attack dynamic. To the extent that for a lazy Blues, I choose to go back to L alone!

Others here believe that reed sound is simply an air/metal thing. Against that I’d say that the keyboard of my Gaillard physically vibrates on low, L voice notes. So there is acoustic coupling into the blocks. The straps, which are in the plane of reed movement should logically increase that coupling? 🤔

Van der Aa doesn’t use straight straps, like other makers. His are 1mm or so wires, bent into lazy Z shapes. From my basic 1 year uni physics I’d expect that to act as a capacitance, ie to phase delay any coupling? He’s adamant that bends in the strap make for better tone .. but then he would say that? 😉 His kit certainly ‘sounds” nice.

I got most “what a lovely sound” conments on my Oakwood however. Sorry, can’t remember if that had straps, but I believe it did. Anyone got one open? 

edit: I think that all 3 melodeons had Binci reeds.   
« Last Edit: October 10, 2021, 01:43:14 PM by Chris Ryall »
Logged
  _       _    _      _ 

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Braces across reed blocks: Why?
« Reply #2 on: October 10, 2021, 02:40:16 PM »

These braces are of vital importance. In my own instrument I always have two of them. The more powerful the reeds, the more important it is to stabilize the blocks in order to avoid unwanted resonance/vibrations. I'm also pretty confident that there is absolutely nothing wrong with the Binci reeds in the Guais. This is a frequent phenomenon and experienced tuners should know how to deal with it.
Logged

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Braces across reed blocks: Why?
« Reply #3 on: October 10, 2021, 02:48:49 PM »

This has been discussed before in a long thread somewhere on MelNet.
If you need them, you need them, but there's no need if your box sounds fine without them.
The commonest problem which they can solve is an irregular warble on a tremolo tuning, especially a swing tuning where the pitches are very close, caused by one reed trying to pull the other into sync with it. When it works, the strap increases the torsional stiffness of the reed block by almost doubling its mass to that of the two blocks combined, and that is enough to stop the vibrations of one reed affecting the other.

Quote
I got most “what a lovely sound” comments on my Oakwood
Same with mine. It does have a strap between the blocks, but made of pearloid plastic with a shallow 'Z' crank in the middle because the blocks have different heights, so it's hard to imagine it adds much rigidity. Also when I checked it just now, one of the screws wasn't tight, so it wasn't doing much at all. I've tightened it up now!
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Braces across reed blocks: Why?
« Reply #4 on: October 10, 2021, 03:04:56 PM »

I have learned from experience how the brace affects the sound.  When I first started to learn tuning techniques I saw these straps and had no idea of their function.  The dawning of understanding came when I started to notice difficulty in tuning a stable tremolo.  Typically a reed block taken out of the instrument and sounded on a tuning bellows would sound perfect, but when fitted and played in the instrument one note would sound terrible with no tremolo or tremolo coming and going.  Fitting the brace instantly cured the problem.  Some instruments don't exhibit this problem others do, even two example of the same make and model can sometimes behave differently.  Usually its a note towards the low end of the range, but high notes can be affected too.

Now coming to the reported instability of Binci reeds.  This is something I've not seen myself, but I'm usually tuning a 1Hz swing.  It sounds as if Jack was after a closer spread.  What I have found with Binci reeds is that it is critically important to get the set adjusted very precisely so that a pair of reeds start to speak at exactly the same moment, and with the least bellows pressure consistent with the playing style of the musician.  This is true of other makes too but is particularity true for Binici and other hand made reeds that typically have thinner and more flexible tongues than most Italian tipo a mano reeds from the bigger makers like VA and Cagnoni.  And of course it should go without saying that the tuning must be done with the blocks fitted to the instrument, and with braces fitted.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Braces across reed blocks: Why?
« Reply #5 on: October 10, 2021, 05:43:40 PM »

This has been discussed before in a long thread somewhere on MelNet.
If you need them, you need them, but there's no need if your box sounds fine without them.
The commonest problem which they can solve is an irregular warble on a tremolo tuning, especially a swing tuning where the pitches are very close, caused by one reed trying to pull the other into sync with it. When it works, the strap increases the torsional stiffness of the reed block by almost doubling its mass to that of the two blocks combined, and that is enough to stop the vibrations of one reed affecting the other.

Quote
I got most “what a lovely sound” comments on my Oakwood
Same with mine. It does have a strap between the blocks, but made of pearloid plastic with a shallow 'Z' crank in the middle because the blocks have different heights, so it's hard to imagine it adds much rigidity. Also when I checked it just now, one of the screws wasn't tight, so it wasn't doing much at all. I've tightened it up now!

The problem -- if it shows up at all -- often only happens on one note. where either the tremolo "warbles", the reeds lock into unison, or they slip in and out of unison. It's caused when a resonance in the reed block coincides with the frequency of the note, usually a torsional resonance along the length of the block -- if you want to talk technical, the mechanical impedance becomes high and the reed no longer sees the block as a solid mounting, and the reeds couple together instead of vibrating separately.

It's most common with notes near the middle of the block, furthest from the ends which are clamped down to the fondo/case and are more rigid. Also depends on the key of the instrument because the problem happens at one particular frequency in the midrange, so for D/G it's often further down the keyboard (lower pitched button) than a G/C. The reed block resonance seems to be quite narrow (high Q) so on nominally identical instruments it might fall right on a note on one (problem) but between two notes on another one (no problem), just due to slight differences in the wood and construction.

Bracing the reed block across to the other reed blocks usually fixes it, because they're unlikely to both have the same resonance frequency -- so when one has a problem the other one stays rigid and vice versa, and the brace doesn't have to be especially rigid for this to work. But if you're unlucky it can just move the frequency to another note, or even cause the problem on an instrument which was fine with no brace...
« Last Edit: October 10, 2021, 05:51:51 PM by IanD »
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Jack Humphreys

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • tunesbyjackhumphreys
Re: Braces across reed blocks: Why?
« Reply #6 on: October 11, 2021, 05:57:07 PM »

I'm grateful for all this expertise, offered so promptly and fully.  I will also check out the previous discussion. Olav is helpful in talking generally about the braces counteracting unwanted resonances. I wonder whether I should try installing a second brace on the treble end to follow his example. Other opinions, like my tuner B's, see the brace's function as helping to maintain an intended tremolo.  But my experience shows that a brace is still needed when the tuning is a totally dry unison.  Without the brace there was an unwanted glitchy attack sound, and this occurred all over the instrument, not limited to one or two notes.
It seems that often a brace is essential; and that some instruments sound as good, or  better, without.

I'm very grateful for the many hours two highly experienced tuners have spent trying to achieve  swing tuning with these reeds.  I do respect their opinion that the reeds are unstable in swing: they are speaking from hands-on experience with this particular box.
So, for the time being, I will make the best of the unison tuning.  ML is my favourite voicing anyway. A good few balfolk star players use bando boxes, with no tremolo, and several individual makers offer only two-voice instruments.

Mark Anderson

  • Member
  • *
  • Offline Offline
  • Posts: 36
Re: Braces across reed blocks: Why?
« Reply #7 on: October 11, 2021, 06:45:44 PM »

Other opinions, like my tuner B's, see the brace's function as helping to maintain an intended tremolo.  But my experience shows that a brace is still needed when the tuning is a totally dry unison.  Without the brace there was an unwanted glitchy attack sound, and this occurred all over the instrument, not limited to one or two notes.
It seems that often a brace is essential; and that some instruments sound as good, or  better, without.

Totally dry unison is an intended amount of tremolo---zero.  >:E
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Braces across reed blocks: Why?
« Reply #8 on: October 11, 2021, 07:30:23 PM »

I’m another bandonèon sound fan, which might explain my “innocence” wrt swing tuned kit. I sold my last such over 20 years ago.

Ian, impedance is a complex number, and both parts vary with frequency as you doubtless know. Yes, one can talk about a “magnitude” but that’s to go even further into the maths?  I follow your point about locking oscillators. Many examples on internet.

I have to bow to the experienced tuners in this, but any oscilloscope data would be invaluable. Another data point for us is Miguel Gramontain’s CBA accordions. The attached picture went onto FB last week commented “bursting at the seams” (French equivalent full as an egg). I read his straps to be of the rigid genre. It doesn’t say how wet tuning its was.
« Last Edit: October 11, 2021, 07:37:30 PM by Chris Ryall »
Logged
  _       _    _      _ 

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Braces across reed blocks: Why?
« Reply #9 on: October 12, 2021, 12:26:25 AM »


Tuner A removed the brace and taped it to the inside of my case. He said that braces kill the soul of the instrument,  which would sound more alive without. John Spiers was quoted as sharing this view.

I'd be curious to make an ABX test to verify that statement. As is the case with many accordion related notions such as this). Apart from the obivous case where the brace will prevent unwanted couplings, I'm not sure at all one would be able to distinguish a sound clip with the brace and without the brace.

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: Braces across reed blocks: Why?
« Reply #10 on: October 12, 2021, 12:44:05 AM »

Had this conversation with Frans van der Aa, who is also a pretty good player. He is firmly of the opinion that the metal coupler is important to tone, though we didn’t discuss the ‘attack” dynamic you mention.

He metal strap couples MM’s, and also across to the L blocks.

He seems to have changed his mind since then. In the 3-v box he made for me in 2020, there are no braces. I asked him why and he said that they are of no benefit for the way he sets his instruments up now. In my box the treble reedblocks are not screwed down or very firmly attached. In fact they are quite wobbly.  :o   

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Braces across reed blocks: Why?
« Reply #11 on: October 12, 2021, 08:12:08 AM »

.
  Ha!   Frans is a lovely fella, but tends to describe his current model as being close to perfection.

   Yet his kit is in constant evolution, I see that as a good thing. But it felt odd that the reeds to
   be fitted to my “compact” changed 3 times in 18 months. I think he had some supply issues, and
   I eventually got Bincis, which was the original order.

   Ditto our deconstructing the (amazingly good) Gaillard air mechanism. Dubious at first, but then
   the “New design vdAa” air valve appeared.  I think it was the build before mine.

   Innovation is good, and I’d refer new joiners to Melnet’s 21st Century Box thread. It’s more a
   heap than an archive, but I’ve tried to collect new ideas there.

   we’ve knocked the straps/ coupling thing about repeatedly. I trust my ears, but I also trust the tuners.

   Time for some science?

« Last Edit: October 12, 2021, 08:14:12 AM by Chris Ryall »
Logged
  _       _    _      _ 
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal