Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Reed block tuning  (Read 3147 times)

0 Members and 1 Guest are viewing this topic.

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Reed block tuning
« on: October 12, 2021, 07:16:54 PM »

I think that I have read/watched somewhere that Hohner tuned a reed block at perfect pitch on one side and then the tremolo was introduced on the opposite side. The orientation was always the same. Is this correct?  …… If so which side is the perfect pitch?   If I take a reed block and hold it with low reeds on left and high on right with face plate on bottom i.e. clamp on right,  is this the perfect pitch side?
Thanks …. Any help would be appreciated.

John
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Henry Piper

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 368
Re: Reed block tuning
« Reply #1 on: October 12, 2021, 07:25:28 PM »

In my experience very few ( if any ) Hohner reeds are at "perfect" pitch they are usually "more or less" tuned !!!
its certainly true that all the on pitch reeds are on one side and the tremelo ones on the opposite side, but I have come across reedblocks where they seem to be randomly mixed,  although that could well have happened long after the assembly at the factory, probably at the hands of an inexperienced after market tuner.
Logged
From Ottery St Mary Devon. Currently Playing Dino Baffetti BP2 in D/G, Hohner Student 1 P.A conversion  in D/G,  Hohner 3515 Pre-Pokerwork in A/D,   2 row "Beaver Brand" in Bb/Eb, Hohner Pre- Erica in G/C .  Single row permanent 4 voice, 4 bass in C from old Hohner single row and bits of a cheap Cajun box !!,

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Reed block tuning
« Reply #2 on: October 12, 2021, 07:43:05 PM »

Most every hohner reed block form a pokerwork/erica has been arranged such that the reeds on the side of the block you can see in the attached photo (of some very scabby reed blocks)  are the tremolo reeds


https://photos.app.goo.gl/JcH2p3h2qu4Vey8U9

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed block tuning
« Reply #3 on: October 12, 2021, 07:44:05 PM »

Usually it’s the side of the block furthest from the keyboard that is at the nominal pitch
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Reed block tuning
« Reply #4 on: October 12, 2021, 08:59:43 PM »

Thanks  (:)

I will map the frequencies tomorrow.  It's an old Modell 1 "Picolo".

I also need to work out what it was set at (suspect original).  I don't think its 440Hz.

Picture of Reed Blocks below :D

Thanks

John

Nominal Pitch Side by John Burks, on Flickr



« Last Edit: October 12, 2021, 09:05:07 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed block tuning
« Reply #5 on: October 12, 2021, 09:26:22 PM »

I see 870 marked in the block which indicates that the original tuning was the old German standard of A=435Hz.

I hope you have fitted new valves to both sides of the reeds.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Reed block tuning
« Reply #6 on: October 12, 2021, 09:52:46 PM »

Hi Theo,  thanks. I wondered if it was 435Hz. I did a quick check earlier with my tuner at 435Hz and was getting pretty good readings.

Re the valves …. I have not yet changed the internals on the treble end (have on bass). The outside ones were curled badly but the treble internals seem to be flat and working.  It was a quick job to change the externals so I did so to see how it played. Also sealed loose reeds.

I now have to decide weather to strip treble end completely or just quick spot tune.

I thought I would map frequencies first and then decide.  It’s an old box but pretty much original.

Your views would be appreciated ….

John
« Last Edit: October 12, 2021, 09:59:20 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Reed block tuning
« Reply #7 on: October 13, 2021, 08:12:52 AM »

Assuming the tremolo reed is pitched higher than the 'concert' reed (whatever that was set to), it’s easy to work out where they are, by pinging the reeds. You don’t need particularly great hearing to tell the difference just from the ping. I often do this with customers if I’m giving them a whistle stop tour of the inside of their accordion/melodeon. I ping both adjacent reeds and they can always hear the difference, so it’s not a specialist skill. Normally (ahem) all the tremolo reeds are fitted on the same side, unless someone has been in there doing some refitting and tuning.

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Reed block tuning
« Reply #8 on: October 13, 2021, 09:10:06 AM »

Thanks  (:)

I will map the frequencies tomorrow.  It's an old Modell 1 "Picolo".

I also need to work out what it was set at (suspect original).  I don't think its 440Hz.

Picture of Reed Blocks below :D

Thanks

John

Nominal Pitch Side by John Burks, on Flickr

A pity the waxing job wasn't left to an expert...
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed block tuning
« Reply #9 on: October 13, 2021, 09:47:31 AM »


A pity the waxing job wasn't left to an expert...

I don't think their has been a "waxing job"   it's just new wax on top of old.   

Much better to do the job properly.   Take all the reeds off, get rid of the ancient dried up wax, new valves on the inside reeds.  Otherwise the effort you have put in may be spoiled by further wax failures and odd noises from old stiff valves on the inside.  And if you plan to tune up from 435 to 440 it will be much quicker and easier to start that process with the reeds off the blocks, then finish the tuning in the instrument.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Reed block tuning
« Reply #10 on: October 13, 2021, 09:58:50 AM »

Just to help do you think the reeds are a little oversized and Heavey.IMHO if doing a new job to 440 either slightly lighter smaller leather or nothing wrong with the modern vynal/plastic reeds that are available in sets. Even dare I say good old leather valves in good condition?

I am not an expert rather what do others feel
« Last Edit: October 13, 2021, 10:00:33 AM by folkloristmark »
Logged
Mark Taylor
Folkloristmark

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Reed block tuning
« Reply #11 on: October 13, 2021, 12:27:36 PM »

Thanks for the really good advice.  It's really appreciated.

I think I was getting a bit lazy and wanted a quick fix  ::)   You are right the only way forward is to do it properly.  I have stripped the blocks and ordered a new set of vinyl valves.

Just to say thanks again here is a photo (will now remove valves, clean, prepare tuning table):

 Good Sound Advice - Stripped by John Burks, on Flickr

When it comes to the first pass tuning of the reeds to the new A440 pitch I assume that its done with the valves in situ? Or can you simply mask? (Would obviously progressively final tune with them in place and then in the block)  As you will probably appreciate by now I have not fully tuned a box like this before but am keen to learn! I'm a great believer in knowing any instrument like the back of my hand!

Ta

John
« Last Edit: October 13, 2021, 12:32:42 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Reed block tuning
« Reply #12 on: October 13, 2021, 12:44:37 PM »

When it comes to the first pass tuning of the reeds to the new A440 pitch I assume that its done with the valves in situ? Or can you simply mask? (Would obviously progressively final tune with them in place and then in the block)  As you will probably appreciate by now I have not fully tuned a box like this before but am keen to learn! I'm a great believer in knowing any instrument like the back of my hand!
Fit the valves before tuning. My plan would be to tune the reeds slightly sharp of what you want as flattening is easier once the reeds are in the box.
I would also bin the nails that were holding the reeds in as they, IMO, achieve nothing and make waxing well more difficult.

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Reed block tuning
« Reply #13 on: October 13, 2021, 02:54:10 PM »

There is a good deal of rust on your reeds, which of course has to be dealt with. Do your pre-tuning before waxing and always without valves. If you set your device to 441.5 Hz you should end up with about 440 Hz on M (as opposed to M+) when the job is finished. The highest reeds (those that do not require valves) should be pre-tuned about 5 to 6 C flat.
https://www.youtube.com/watch?v=PJdU8l4foRA&ab_channel=diatonix2
« Last Edit: October 13, 2021, 03:02:01 PM by diatonix »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed block tuning
« Reply #14 on: October 13, 2021, 02:59:03 PM »

Yes, pre-tune without valves.  And get all traces of old wax off the blocks and reed plates.  Scrape with an old blunt knife blade, then brush with a soft wire brush.  The type that used to be used for suede shoes works well. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Reed block tuning
« Reply #15 on: October 13, 2021, 04:42:48 PM »

I would also bin the nails that were holding the reeds in as they, IMO, achieve nothing and make waxing well more difficult.
I quite agree. They only tend to damage the walls separating the chambers.
Logged

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Reed block tuning
« Reply #16 on: October 13, 2021, 04:47:12 PM »

Thanks  (:)   

I have binned the nails. I have also found my old "brass bristle" brush and have started cleaning.

I even found myself looking online at Suede Desert Boots once I had found the brush  ::)

Thanks again for all the advice .  I appreciate the help.

John
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Reed block tuning
« Reply #17 on: October 15, 2021, 08:54:54 PM »

There is a good deal of rust on your reeds, which of course has to be dealt with. Do your pre-tuning before waxing and always without valves. If you set your device to 441.5 Hz you should end up with about 440 Hz on M (as opposed to M+) when the job is finished. The highest reeds (those that do not require valves) should be pre-tuned about 5 to 6 C flat.
https://www.youtube.com/watch?v=PJdU8l4foRA&ab_channel=diatonix2

Ok I have cleaned all reeds and have reduced/eliminated rust deposits (quite therapeutic - taking time to clear each one - they all now ping extremely well - thanks for sound advice re taking time and doing this properly).  I have also prepared a tuning table in line with video (approx). Having read previous posts I have tried to emulate a reed block chamber in its design and have sized the bellows and the aperture to match the finished box. I now need to pre-tune.  I prefer to tune in Hz so was going to pre-tune all to A440 to about plus 2 Hz across all reeds for M which I think aligns with the above (roughly). I will then valve and transfer the reeds to the block. I will then tune to A440 in the block hopefully only having flatten slightly. Does this achieve the same effect?  I notice above though that the non-valved reeds should be handled differently. I take it that the valves are likely to flatten by 1.5 - 2 Hz so adjusting re the non valved reeds is required. I should pretune those  to pure A440?

BTW the above only applies to the M bank. I will establish a beat rate on M+ By increasing Hz in a range  1-7 Hz ish to suit the beat curve I want to achieve.  Does this make sense?

Any advice would be appreciated.

Ta

John
« Last Edit: October 15, 2021, 09:11:26 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Reed block tuning
« Reply #18 on: October 15, 2021, 09:44:56 PM »

There is a good deal of rust on your reeds, which of course has to be dealt with. Do your pre-tuning before waxing and always without valves. If you set your device to 441.5 Hz you should end up with about 440 Hz on M (as opposed to M+) when the job is finisher . The highest reeds (those that do not require valves) should be pre-tuned about 5 to 6 C flat.
https://www.youtube.com/watch?v=PJdU8l4foRA&ab_channel=diatonix2

Ah ….. please ignore previous post (I will leave it as it is).  I have just twigged that you are suggesting that you set at 441.5 Hz and tune each note to perfect pitch (A441.5 Hz and cents = 0). This gives you the offset (variable Hz🙄) and leeway for valves/flattening in block if you have too.  The higher reeds (without the valves) consequently should be flattened slightly at 441.5 Hz (- 5-6 cents) to achieve a final perfect pitch at or near A440 Hz.

So I pre-tune at 441.5 Hz and then final check/tune at 440 Hz.

Thanks so much for the input. 

I may be wrong but I think I now understand what I’m doing.   Ta

John

PS please tell me if I’m still getting it wrong 👍
« Last Edit: October 15, 2021, 10:25:58 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Reed block tuning
« Reply #19 on: October 15, 2021, 09:51:56 PM »

I suppose the original tuning was a good deal lower than 440 Hz. It may be a good idea to check the smallest reeds first and decide whether it's advisable or not to file their tip all the way up to modern pitch.
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal