Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Reed block tuning  (Read 3139 times)

0 Members and 1 Guest are viewing this topic.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed block tuning
« Reply #20 on: October 15, 2021, 10:02:12 PM »

Good plan.
Valves on their own don’t flatten the pitch do much, but combined with fitting to the reed block and placing the reed block in the instrument it’s probably about right.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Reed block tuning
« Reply #21 on: October 15, 2021, 10:03:50 PM »

I suppose the original tuning was a good deal lower than 440 Hz. It may be a good idea to check the smallest reeds first and decide whether it's advisable or not to file their tip all the way up to modern pitch.

Thanks.  Will do.  Really good advice ….

The box was gifted to me so I want to be careful with it.

I will check tomorrow. I have ruined reeds recently by over filing and so don’t want a repeat.  Really appreciate the input 👍

Once I have the Hz figure I will post 😊
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Reed block tuning
« Reply #22 on: October 15, 2021, 10:07:32 PM »

Good plan.
Valves on their own don’t flatten the pitch do much, but combined with fitting to the reed block and placing the reed block in the instrument it’s probably about right.

Thanks Theo …. I will check out tomorrow and report.

Really appreciate the input.  Hopefully I will get it in tune eventually … it’s a winter project so plenty of time 😊👍
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Reed block tuning
« Reply #23 on: October 15, 2021, 10:12:27 PM »

Will get there eventually  ;D .... A picture of this afternoons efforts:

Tuning Table by John Burks, on Flickr

Operated by knees!
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed block tuning
« Reply #24 on: October 15, 2021, 10:59:32 PM »

It’s very helpful to keep hands free. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Reed block tuning
« Reply #25 on: October 16, 2021, 06:41:55 AM »

May I suggest, John, that a thinner top plate on the tuning bellows is likely to give you a result much closer to the desired pitch when the instrument is assembled, so less fine tuning. I eventually settled on 3mm ply; my original set up had a 10mm top, and if reeds were tuned to concert pitch it resulted in somewhere around 20cents sharp when mounted in the instrument, which I believe is caused by a "tunneling effect".
Google the term in relation to sound waves at your own risk, but the physics is well beyond me  :-(

Logged
Tuner/repairer, now retired.

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Reed block tuning
« Reply #26 on: October 16, 2021, 11:12:11 AM »

May I suggest, John, that a thinner top plate on the tuning bellows is likely to give you a result much closer to the desired pitch when the instrument is assembled, so less fine tuning. I eventually settled on 3mm ply; my original set up had a 10mm top, and if reeds were tuned to concert pitch it resulted in somewhere around 20cents sharp when mounted in the instrument, which I believe is caused by a "tunneling effect".
Google the term in relation to sound waves at your own risk, but the physics is well beyond me  :-(

Hi Malcolm,  many thanks.  I will give it a try  :D.   I have a nice piece of 3mm modelling ply which will do the job nicely.

It has also made me think things through more and I’ll do a few tests to see what offsets I am getting (table - block - body) before launching in.

Thanks again … good sound advice …. Making me think is good 😁

PS I Googled it …..
« Last Edit: October 16, 2021, 11:28:14 AM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Reed block tuning
« Reply #27 on: October 17, 2021, 06:42:59 PM »

I have been working on cleaning up these reeds and was having difficulty keeping track of them (position/orientation).  The solution has been to use the reed block as a stand.  I had to search out the pins having binned them but now I have a temporary rack which makes things much easier (pins only slightly pushed in - not to be kept once finished tuning)  The addition of elastic bands helps retain the reeds as I move them about.
The work flow is  now - two reeds plates out  at a time to tune and them back in the rack. Its much easier and you don't loose track re what you are doing.

I just thought that I would share:

Working on reeds - safe storage. by John Burks, on Flickr

Works for me.

John
« Last Edit: October 17, 2021, 06:45:49 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal