Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Can I retrofit my Hohner HA-114 with these reeds?  (Read 741 times)

0 Members and 1 Guest are viewing this topic.

Tucker Manuel

  • Member
  • *
  • Offline Offline
  • Posts: 5
Can I retrofit my Hohner HA-114 with these reeds?
« on: October 31, 2021, 05:17:00 AM »

I found some Harmonikas D and Bb reeds that I’d like to retrofit into my C and G Hohners respectively.  Will they work with the existing reed blocks, or can I adjust the reed blocks to make them work?
« Last Edit: October 31, 2021, 06:52:17 AM by Tucker Manuel »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Can I retrofit my Hohner HA-114 with these reeds?
« Reply #1 on: October 31, 2021, 08:09:39 AM »

Harmonikas reed plates are usually significant longer than Hohner,  how much can only be seen by putting them side by side.  So it’s likely that some reed chambers will need to be lengthened.  Harmonikas reed plates are usually a bit thicker too which might make for difficulty in fitting the reeds on the sides of the treble blocks that face each other.
Perhaps someone has done this already and can share their experiences.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Can I retrofit my Hohner HA-114 with these reeds?
« Reply #2 on: October 31, 2021, 01:20:06 PM »

I believe Lars Hansen of this parish did something like this with a Hohner HA114.
Logged
C#/D player

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: Can I retrofit my Hohner HA-114 with these reeds?
« Reply #3 on: October 31, 2021, 11:11:39 PM »

i have a harmonikas D set in stock....i'll check how they sit in a C ha114...i think i have one stripped and ready for a refit
Logged

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Can I retrofit my Hohner HA-114 with these reeds?
« Reply #4 on: November 01, 2021, 10:34:02 AM »

On Harmonikas’ website is a table giving all the possibilities of their reed plate dimensions for a given pitch so you can measure and check against the space you have available in the instrument.  You can minimise the work needed by ordering reeds as close as they can do to existing sizes, but yes, you will have to make at least some modifications to Reed chamber dimensions.

Be aware though that if the instruments with their current Hohner reeds play nicely with good fast and crisp responsiveness, they won’t necessarily feel quite the same afterwards . . . . .
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Can I retrofit my Hohner HA-114 with these reeds?
« Reply #5 on: November 02, 2021, 11:57:07 PM »

Having struggled a bit to get Harmonikas reeds to sit opposite one another on the bass side of a Hohner, due to the thick plates, I’m guessing you might have a similar issue on the glued in blocks on the treble side of a 114 (I think I had to sink the lower half of the reed plate into the bass chamber so that the rather large rivets didn’t foul each other). Also, you might need to chop out a bit of the Reed chamber to accommodate some of the lower end reeds, which might be tricky on these pesky glued in blocks...conclusion.... it might not be straight forward.
« Last Edit: November 03, 2021, 12:01:05 AM by RogerT »
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal